Congrats for all your series about Arduplane and Arducopter. The level of details are really extremely useful for immediate practical use 👍. Pls. continue to keep us informed and updated.
Good video But you have shown parameters value and change it. There is no back information why to change? When change this value? How to estimate and calculate this parameter value? Can make brief explain only pid control tuning based on flight test method and based on log analysis
Now I have a problem to test the water pump. I tested by using Esc with 2 signal wires, white and black, connected to the brushless motor instead of the water pump, but the motor does not work. I connected the wire to AUX1 SPRAY_ENABLE 1 SERVO9_FUNCTION 22 RC6_OPTION 15 Please advise me.
I’m having some problems myself, I can’t get higher speed than 2700 Rpm , I am very new to all this but keen to learn ,any help or suggestions I’m very grateful ,I’m using Arducopter.
bruh, I'm willing sell off my fixed wing components like Fc, gps, transmitter, etc. is there any community group around this to make this happen ? leme know
Hello my friend and thank you for everything. I want to start autonomus mission plan but when i arm the drone and press the button do action. It does not start. I flying near red zone (airport) is this the reason??
Hello, Don't fly in the red zone. That's not the reason. Arm the drone in loiter mode. Additionally, ensure that you include a takeoff command in your mission plan. Keep the throttle at zero.
do you have LED problem with X6plus motors? It happens when you activate the safety switch and then deactive it and LEDs start blinking and doesn't stop also when arm
The LED status serves as an indicator of the ESC's operational state. During flight, it remains steady, signifying normal operation. However, in the event of over voltage, over current, overheating, or loss of throttle signal, the LED will blink to alert the user of the issue.
@@karthikstechtime0910 in normal situation, when you select "virtual hardware safety switch" in missionplanner ESCs start bipping and blinking. and if you select that again, the LEDs are still blinking. it's not happening in X8 or X9 motors
Thanks for the great tuning video. Very well explained.
Congrats for all your series about Arduplane and Arducopter. The level of details are really extremely useful for immediate practical use 👍.
Pls. continue to keep us informed and updated.
Thanks..
Great job Karthik. An amazing video that takes a lot of work. Subbed.
Thanks..
Amazing content. explained very well sir.
Thanks for watching..
What are all the components of a plane and what is the control device?
Hobbywing X6 plus propulsion system, CUAV X7 Plus flight controller & Skydroid T12 Radio Controller.
Good video
But you have shown parameters value and change it.
There is no back information why to change? When change this value? How to estimate and calculate this parameter value? Can make brief explain only pid control tuning based on flight test method and based on log analysis
Sure! I will try to make a detailed video on how to tune the parameters and explain their effect.
Now I have a problem to test the water pump. I tested by using Esc with 2 signal wires, white and black, connected to the brushless motor instead of the water pump, but the motor does not work. I connected the wire to AUX1 SPRAY_ENABLE 1
SERVO9_FUNCTION 22
RC6_OPTION 15 Please advise me.
Try SERVO9 - 56
I’m having some problems myself, I can’t get higher speed than 2700 Rpm , I am very new to all this but keen to learn ,any help or suggestions I’m very grateful ,I’m using Arducopter.
Hello Karthik bro, can you please make same video for k++ v2 hexacopter for fine tuning.
Hi.. I will try..
ua-cam.com/video/W5n73SqBWa8/v-deo.html
very great video!!! are you using fc damper???
Yes.
GREAT BRO
Thanks
are the values mentioned only applicable for this hexacopter? or can it be used for all the quads? like F450
The tuning values may differ according to the frame size, weight, configuration of propulsion system.. You can the same value for identical system.
Hi, Harshal this side actually I want to create a drone and want some guidance, if it is possible can we connect?
Karthikaeromodeller@gmail.com
Hi mate how did you setup the c-compass to make it works properly, did you set the c-compass into priority 1 or priority 2? Thanks
The compass can be directly connected to the I2C port and assigned priority 1.
Where do u buy the components ?
And what is the total cost of this drone brother ?
Approximately 1.6L excluding batteries.
Hello karthik sir, I am thinking of building a drone and need some guidance can you help?
Karthikaeromodeller@gmail.com
bruh, I'm willing sell off my fixed wing components like Fc, gps, transmitter, etc. is there any community group around this to make this happen ?
leme know
Kindly check the rcgroups forum for more information.
Hello my friend and thank you for everything. I want to start autonomus mission plan but when i arm the drone and press the button do action. It does not start. I flying near red zone (airport) is this the reason??
Hello,
Don't fly in the red zone. That's not the reason. Arm the drone in loiter mode. Additionally, ensure that you include a takeoff command in your mission plan. Keep the throttle at zero.
total cost to setup ag drone
2.5L without Battery and Charger.
do you have LED problem with X6plus motors? It happens when you activate the safety switch and then deactive it and LEDs start blinking and doesn't stop also when arm
The LED status serves as an indicator of the ESC's operational state. During flight, it remains steady, signifying normal operation. However, in the event of over voltage, over current, overheating, or loss of throttle signal, the LED will blink to alert the user of the issue.
@@karthikstechtime0910
in normal situation, when you select "virtual hardware safety switch" in missionplanner ESCs start bipping and blinking.
and if you select that again, the LEDs are still blinking.
it's not happening in X8 or X9 motors
I probably missed that part, but i would like to ask if you used the Autotune command or you made all the procedure by trial and error. Thank you
I adhered to the arducopter manual tuning process and followed the preparation procedure for the maiden flight.