Simple Arduino Energy Meter | Volt -Amp meter 20 Amp

Hello friends, today in this video I've shown how to make an arduino energy meter which can measure current upto 20Amp.
Components used:-
1. Arduino Nano
2. 16/2 LCD Display
3. ACS712 Current Sensor (Using 20A)
4. 2.2K Resistor
5. 47K Resistor
6. 10K Potentiometer
For code and schematic click the link below
drive.google.com/drive/folder...

[@kambeizkerach9747]

you are the best.
thanks for sharing it👌👨‍🎓

[@Bianchi77]

Creative video, thanks for sharing it :)

[@xpertgamer0]

nice Volt -Amp meter 20 Amp0 nice work

[@Dailyoneminute1]

By the way, great work sir

[@ashraf9472]

يعطيك الصحة والعافية ياهندسة

[@electronic7979]

Excellent project

[@SC.243k]

Wow awesome ideas

[@chrishadjipetris6059]

Does it display real, or apparent power? Because if it's a simple code that just takes voltage and current and multiply them, it displays apparent power, which can be equal in case of resistive loads, but not for inductive or capacitive loads.

[@raffaelebarlotti9017]

Excuse me, I also wanted to know up to what voltage and current can be applied to the input? Thanks.

[@lowcosttech8026]

goodjob.. my question is can I modified ready made volt-ampere meter 10A to 50A? if yes. how? thanks

[@yogeshbhuva3713]

Good work sir
Use this voltage 24v

[@francisderenge3052]

Hie thanks for sharing, am planning to use this ... On the code there is delay(1000), would that interfere with other programs i will add running in the void loop()

[@raffaelebarlotti9017]

Hi, congratulations on the project! I made the circuit but the Ampere measurement is not exact (the measurement on the display is greater than about 2 Ampere), can it be calibrated and how? Thanks.

[@Hello-nh3my]

Using the trimmer pot to the correct voltage you seen in the correct source

[@ahmedfarid7775]

what is the program U use to make a schematic simulation of the circuit ?

[@chandansaha5286]

It was a great videos. I want to measure current in microamps, what kind of circuit can i use.

[@makinetasarm8694]

Hocam merhabalar bu işlemi esp32 ve arduino nano kullanarak serial bağlayarak blynk ekranından ve 16x2 lcd ile yapabilirmisiniz? Lütfen simdiden tesekkur ederim.

[@ranulfo102]

TOP SEU PROJETO AMIGO. PARABÉNS. SÓ ME DIZ UMA COISA, É POSSÍVEL AUMENTAR O LIMITE DE CORRENTE E DE TENSÃO ?

[@natenut1694]

Is there a way to scale this project up to measuring power exceeding 500watts in a solar panal

[@MrNetworx]

Good, very good. :)

[@techag9344]

Good👍

[@sneakypeek100]

Can we power it using single source?

[@aufadavinio4544]

Hello sir, I want to ask, what happens if when measuring the positive and negative voltage it reverses, will the Arduino be damaged?

[@brajesh5635]

Same for 5amp current sensor? Please reply

[@Chris-sc3rf]

How much voltage is it able to measure? I need to measure about 55V-60V. Will that work?

[@adhimlubis3105]

what voltage can be measured?

[@qadeer1685]

Good

[@leonelhs]

max volt? can test DC/AC?

[@TheElectricianPractice]

👍👍👍

[@ilyesbahmani3727]

Hello what’s the role of pot please ?

[@idushandilitha9181]

What is this maximum voltage check

[@nikhilmaliyan7774]

Can u please tell connection of +5v

[@makinetasarm8694]

Merhabalar bu projesi olduğu gibi esp8266 lolin ile uzaktan takip etmek için yapmaya çalıştım blyk uygulaması ile bir türlü yapamadım? Haberleşmenin sağlayamadım yardımcı olursanız çok sevinirim şimdiden çok teşekkürler.🙏

[@terlumunjoseph6779]

why not make for ac measurements

[@dadomichalovic6348]

Hi i have a problem, it shows me 35v on display without acs712 connected to any source, is it chance that you know a solution?

[@raphaelcacanog73]

If i used arduino uno, is it still the same pin configuration from arduino nano?

[@TechIdeasAG]

Yes

[@umersiddiqui4803]

Tell us the connections of +5v also

[@rajdip675]

Wow

[@taufiqrochman7633]

mister, am a new student of electrical eng. a have a project to make a joulemeter to display efficiency of power in real time ( wh/m in real time ), efficiency in percent ( wh/total distance ), and the mileage. these are parameters of electric vehicle ( urban electric vehicle ), can u help me to make the joule meter? tysm, sorry if iam bothering u

[@hasankaperera771]

Thank you very much
Maximum voltage ?

[@user-sh7dd7zn4o]

Probably 25 volts

[@Dailyoneminute1]

Only 15volt

[@nobinobi4768]

your high watage resistor is 5w but display shows 37 watts Why ???

[@user-bw7yt8rc9b]

Maximum voltage?

[@makinetasarm8694]

.

[@RaviRanjanKumar-rd3bj]

Can we add Arduino UNO in place of nano

[@Dinesh-Bhardwaj]

Absolutely

[@muneeshkhurana8314]

can we use arduino uno in it ?

[@TechIdeasAG]

Yes, ofcourse

[@muneeshkhurana8314]

@@TechIdeasAG i have 16*2 LCD screen with I2C adapter for it , how to connect it , it has 4 output pins as gnd, vcc , sda and scl , how to connect it

[@AlchemistDD]

Besteht die Möglichkeit, dass Du Dir die Hände wäschst, bevor Du das nächste Video machst? So schmutzige Hände sehen einfach unappetitlich aus.
Danke Dir!

[@mitropoulosilias]

why is there a 10k pot?

[@mathsmadesimple556]

To adjust contrast

[@SaugatAmbohangjr]

Where to download code sir

[@TechIdeasAG]

Given in the description

[@Random_Guy-ns3iv]

The code is not showing up. Any solutions/suggestions?

[@tolotolo6192]

You have to be on a computer

[@tolotolo6192]

it does not work on the phone

[@BitSmythe]

You’re obviously very smart. But instead of porn music, like mama said, *USE YOUR WORDS* _Descriptions would be _*_WAY_*_ better._

[@skidkev6421]

Atleast enable your video to be downloaded