Watch out - when using the spoon to remove the needles, make sure it's align to 0 or a reference mark as you will need to put it back in exactly the same position. My Fox now appears to idle at 0rpm... Many thanks for the very helpful videos though, it helped me replace the indicator buzzer on the back of my clocks!
Thanks Very much, your strip and soldering iron t bar worked enough for me, I got the milage showing again in full, which was my main requirement, the clock and distance counter are still not fully showing, but I am sure that was down to not having an exact line up on the strips on my part before heat gluing, however at least I will be able to sell the car now with the milage showing which was main requirement. So I would fully recomend this cheap fix. Removing the unit is fairly easy and can be looked up on the net. I cleaned the old glue off the carbon pads using a cotton wool bud and nail polish remover and used a credit card for the lcd glass. A tip to others doing this fix is to take a photo of the dials before you remove them and dont screw the panels back on the car until you have checked the speedo calibration after refixing them, I didnt take a photo and had to remove the unit and speedo needle and re-fix it a few times to get it back to 0 at a stand. First time was at +10mph second time -10mph, 3rd time I got it right. Again the fault was on me. This is well Worth a go for a fairly compitent diy er. I am pleased with the result. Worst case you may need a couple of strips incase first one not quite correctly aligned.
I'm about to purchase a VW Fox that has this problem. How much is the part? How much would it be for the part and to have it fixed. I couldn't do this myself....
Hello buddy! I did fix that myself but now the speedo doesn’t show the correct speed and the rev doesn’t work at all! What’s the trick to calibrate the speedo? At what position I should put the dials? Thx in advance
Warning light to show that front lights are switched on, light alerting overheating of the motor. If I good understand, it’s not incandescent buble but led directly soldered on the circuit board... Thanks
Watch out - when using the spoon to remove the needles, make sure it's align to 0 or a reference mark as you will need to put it back in exactly the same position. My Fox now appears to idle at 0rpm...
Many thanks for the very helpful videos though, it helped me replace the indicator buzzer on the back of my clocks!
Thanks Very much, your strip and soldering iron t bar worked enough for me, I got the milage showing again in full, which was my main requirement, the clock and distance counter are still not fully showing, but I am sure that was down to not having an exact line up on the strips on my part before heat gluing, however at least I will be able to sell the car now with the milage showing which was main requirement. So I would fully recomend this cheap fix. Removing the unit is fairly easy and can be looked up on the net. I cleaned the old glue off the carbon pads using a cotton wool bud and nail polish remover and used a credit card for the lcd glass. A tip to others doing this fix is to take a photo of the dials before you remove them and dont screw the panels back on the car until you have checked the speedo calibration after refixing them, I didnt take a photo and had to remove the unit and speedo needle and re-fix it a few times to get it back to 0 at a stand. First time was at +10mph second time -10mph, 3rd time I got it right. Again the fault was on me. This is well Worth a go for a fairly compitent diy er. I am pleased with the result. Worst case you may need a couple of strips incase first one not quite correctly aligned.
How did you change the cable between the lcd glass?
yes, It would be interesting to see how this part is done.
O cabo flat é autocolante nos terminais?
Também queria saber
How easy is it to put different colour led lights in to the consolo
good afternoon. please tell me where you bought or perhaps buy this display. since i have a similar problem. thanks for the help
I’ve got similar problems can’t see time or mileage
I'm about to purchase a VW Fox that has this problem. How much is the part? How much would it be for the part and to have it fixed. I couldn't do this myself....
Hello friend, Do you have the complete video of this repair?
Hello buddy! I did fix that myself but now the speedo doesn’t show the correct speed and the rev doesn’t work at all! What’s the trick to calibrate the speedo? At what position I should put the dials? Thx in advance
Danke fürs Video
my car baord doesnt work at all and there is no électricité in the motor could please what to do thank you
very nice! What do you use to clean the pads and what do you use to bond the cable back?
Cable has heat activated bonding glue already on it, you can't reuse an old/original cable, cheers www.akspeedo.com/
Thanks for your reply!!! Where can I find this flat cable to buy?
Available on our website www.akspeedo.com/ VW page, cheers
looks good. im going to buy the cable from your site its pretty cheap. what is best to clean the pads with though?
Drop us an email one you've placed your order, cheers
Did it today. Clean carbon pads with acetone and use technical alcohol on the display.
Hello,i have new panel and when i change for te old one the car no start but all the light yes,only the block car orange light its on and no start
Speedometer is key coded, can't be swapped out, James
There are some lights broken in my dashboard, is it possible to repair it?
How do you uncounted the dashboard?
Thanks
Hi, What lights are failing?
Warning light to show that front lights are switched on, light alerting overheating of the motor.
If I good understand, it’s not incandescent buble but led directly soldered on the circuit board...
Thanks
Yes, correct, SMD LED soldered to the board, cheers
first time iv seen some one use a spoon !!, never tried it,
take a look at this, at time 9:30, maybe aplying heat to the existing cable would get it done, ua-cam.com/video/-QZk9WCz-D8/v-deo.html
amigo bom dia onde encontro este LCD por favor
hello i am from algeria i am looking for a modu ecu magniti marilli polo fox 1.0 year 2006 (030.906.034.k)
Não entendi merda nenhuma em inglês!👎