Hi Quad, please help. I have a problem with my ST10+ touch screen which is not responding to the touch properly. An area of the lower part of the screen keeps on activating and opening up even without me touching the area, because of this other areas of the screen are compromised and cannot access and not responding to the touch because of this. I noticed the problem started after I stuck on both suctions pads from the black sunvisor on to the front screen as I was getting too much glare from the sun. I am thinking the suction pads may have been pressed in too hard against the screen and somewhat damaged the screen touch panel. Looking forward for your expert advise. Thanks
Neo Cuison Well this is not a quick fix. the digitizer that detect your finger is malfunctioning, do this it would need to be replaced. I would Google around to see if there's any used not functioning remotes. of course making sure that the screen is not broken. you could also try to call the manufacturer and see if you can get a replacement from them. Unfortunately they always want you to send it to them. good luck
Heck I tightened very well all my blades , turned it on first time and 2 rear ones flew off , I hope the motor wiring aren't backwards for those two . Thanks good vid , should help me with a few things.
so after a crash, the camera wouldn't conect. I did the factory reset. camera still doesn't work, now the quad doesn't work. says it's still bind(ed) but no motor start. what do I do next? I know you said ti download the something into something?????????????? etc.
after a reset you must re-bind the copter and then camera. remember to bind the quad turn on the remote first. let it fully boot. then turn on the Q then tilt the Q 45 degrees and the led will flash. now in the remote you must create a Quad then bind it. then add the camera. hope this helps.
I'm hoping you can help me. According to the flashing light indications on my Typhoon G "The aircraft is not connected/linked to the transmitter" I believe the reset button was pushed and lost the default data. Any ideas would be appreciated.
Hello, same thing happens to me, but creating a new copter and bindning during flashing yellow led doesn't work. Do you have any clues? Are there any config files in the system that I can update?
My ST10+ doesn't show my cgo3 in the camera select setting. I have already completed the binding process and s successfully connected it. What do you recommend I do?
Hi Quad Copter. I have Typhoon G with ST10+ controller. I deleted the "Typhoon G" model type unintentionally. How can I retrieve this model type in the "model select function" from the controller? Can i create new model type from the other existing models. Is it correct? It Work?? Help me please!!!!
I was hoping to send you a pm but this will have to do.You've come up with some hacks for the ST10. I was wondering if along the way you figured out how to disable the NFZ disabling feature yet? It's making the Q500 4K useless in my area. tia
I'm working on it. i don't live near an airport so I cant test my changes. we should be able to disable the NFZ due to the fact the FAA said we can as long as we contact the person in charge of the tower.
+chase I agree with the outrage. the st10 has the ability to fake the GPS. But the copter needs to know where the remote is and that's the problem. if you can turn the advance logging when in NFZ we may see the how and why. send me an email to NFZ @ pctriage dot com. that way i can point you to the logging options.
+chase My Q500+ is sitting at home useless as well. Our city allows us to fly R/C planes at a specified park that's 4 miles away from the airport. It's no fair that others could fly there, and I can't. Those dumb asses at Yuneec better smarten up, because I'm never gonna buy their products again until they fix this. I paid $1,800 CAD for a useless junk. I can't fly any where in my city. I will be building my own quadcopters from now on.
You can turn off any/all GPS all day long and if you are in a Yuneec mandated NFZ the props won't start and you can't fly-period. If you can find someone with the Q500_v1.07_10_05_2015_no_airport .bin file then you can load this firmware on the Q series and you can fly anywhere. Or contact Yuneec support, sign a few wavers and they will email it to you.
hola, tengo un blade chroma drone 4k, la radio es una st10+ y tengo un problema, no volaba mi drone hace como 3 meses, cuando lo encendi, y se conecto a la radio, en modo smart el drone empezo a emitir un sonido intermitente, que no logro quitarle, solo se le quita cuando lo paso a modo AP (angle), intente volarlo pero no responde al control cuando lo quiero hacer girar sobre su eje, que hago??? bueno, necesito ayuda, y solo hablo español y frances, y algo entiendo de ingles, gracias!!!
+Quad Copter no impossible because all the different firmware are called update.zip?!?! I can roll back the tx update that is in the folder but update.zip is on root sd card.
Here is my first version of the ST10 Menu Flow Guide. I wanted to post it so if you find something missing, spelled wrong, or comments please let me know. Version 1.0. goo.gl/BpYKxI Some other files. goo.gl/zKzMXq Live long and Fly
I'm From Dubai , recently i buy a Yuneec typhoon q500 4k drone i didn't fly that drone even one time , its drone is problem , I have problem with Yuneec typhoon q500 4k cgo3 wifi problem , Its not binding the camera wifi not showing in controller and i attached steady grip cgo3 camera its not showing wifi in mobiel the camera showing white light only its no response light any color changes , controller working gimbel and drone , the camera only not showing video in controller
I agree with earlier comments that this is an excellent video. Thanks for taking time to upload it. It probably saved me weeks or months of drilling down into those sub-menus and most likely I would have fouled up the ST-10 trying to select some of the features. It truly is a "must-see" for newbies and all Q500 pilots.
Ronald Abalos "a piece of computer code or information providing a quick or inelegant solution to a particular problem" The is no manual showing most of this information. What are you looking for?
Por que no sale el modelo del drone ?? Tengo ese problema 😢en mi Chroma 4k no se conecta la a la radio yuneec st10
There has not been an update for the Q500 but there was a firmware update for the ST10+ (st10+v01b31c) released 12/28/2016
Happens if it gets factory reset what do I have to do to fix it so my drone will fly again
Hi Quad, please help. I have a problem with my ST10+ touch screen which is not responding to the touch properly. An area of the lower part of the screen keeps on activating and opening up even without me touching the area, because of this other areas of the screen are compromised and cannot access and not responding to the touch because of this. I noticed the problem started after I stuck on both suctions pads from the black sunvisor on to the front screen as I was getting too much glare from the sun. I am thinking the suction pads may have been pressed in too hard against the screen and somewhat damaged the screen touch panel. Looking forward for your expert advise. Thanks
Neo Cuison Well this is not a quick fix. the digitizer that detect your finger is malfunctioning, do this it would need to be replaced. I would Google around to see if there's any used not functioning remotes. of course making sure that the screen is not broken. you could also try to call the manufacturer and see if you can get a replacement from them. Unfortunately they always want you to send it to them. good luck
Heck I tightened very well all my blades , turned it on first time and 2 rear ones flew off , I hope the motor wiring aren't backwards for those two . Thanks good vid , should help me with a few things.
so after a crash, the camera wouldn't conect. I did the factory reset. camera still doesn't work, now the quad doesn't work. says it's still bind(ed) but no motor start. what do I do next? I know you said ti download the something into something?????????????? etc.
after a reset you must re-bind the copter and then camera. remember to bind the quad turn on the remote first. let it fully boot. then turn on the Q then tilt the Q 45 degrees and the led will flash. now in the remote you must create a Quad then bind it. then add the camera. hope this helps.
I'm hoping you can help me. According to the flashing light indications on my Typhoon G "The aircraft is not connected/linked to the transmitter" I believe the reset button was pushed and lost the default data. Any ideas would be appreciated.
at 8;51 you will find how to create a quad copter model.
then you will need to bind it.
Hello, same thing happens to me, but creating a new copter and bindning during flashing yellow led doesn't work. Do you have any clues? Are there any config files in the system that I can update?
Try going to Yuneec's site and reading the manual for the bird. It is very simple and takes seconds to bind unless your equipment is shot.
Is there a screen brightness control?
GR8 Question!.. I know there is a volume control, but can't find a screen brightness control.
Can you tell me where it says format camera SD card.I have not seen it anywhere.
You can't format on the transmitter. You need to format the SD card on your computer.
My ST10+ doesn't show my cgo3 in the camera select setting. I have already completed the binding process and s successfully connected it. What do you recommend I do?
lamount hicklin : hello, what cameras do you see?
Hi Quad Copter. I have Typhoon G with ST10+ controller. I deleted the "Typhoon G" model type unintentionally. How can I retrieve this model type in the "model select function" from the controller? Can i create new model type from the other existing models. Is it correct? It Work??
Help me please!!!!
Hello I have the same problem just now, did you solve it? What?
I was hoping to send you a pm but this will have to do.You've come up with some hacks for the ST10. I was wondering if along the way you figured out how to disable the NFZ disabling feature yet? It's making the Q500 4K useless in my area. tia
I'm working on it. i don't live near an airport so I cant test my changes. we should be able to disable the NFZ due to the fact the FAA said we can as long as we contact the person in charge of the tower.
+chase I agree with the outrage. the st10 has the ability to fake the GPS. But the copter needs to know where the remote is and that's the problem. if you can turn the advance logging when in NFZ we may see the how and why. send me an email to NFZ @ pctriage dot com. that way i can point you to the logging options.
+chase My Q500+ is sitting at home useless as well. Our city allows us to fly R/C planes at a specified park that's 4 miles away from the airport. It's no fair that others could fly there, and I can't. Those dumb asses at Yuneec better smarten up, because I'm never gonna buy their products again until they fix this. I paid $1,800 CAD for a useless junk. I can't fly any where in my city. I will be building my own quadcopters from now on.
The dumb ass was you for not reading the specs and learning about the law. BTW turn off the GPS mode and the bird will fly moron.
You can turn off any/all GPS all day long and if you are in a Yuneec mandated NFZ the props won't start and you can't fly-period.
If you can find someone with the Q500_v1.07_10_05_2015_no_airport .bin file then you can load this firmware on the Q series and you can fly anywhere. Or contact Yuneec support, sign a few wavers and they will email it to you.
hola, tengo un blade chroma drone 4k, la radio es una st10+ y tengo un problema, no volaba mi drone hace como 3 meses, cuando lo encendi, y se conecto a la radio, en modo smart el drone empezo a emitir un sonido intermitente, que no logro quitarle, solo se le quita cuando lo paso a modo AP (angle), intente volarlo pero no responde al control cuando lo quiero hacer girar sobre su eje, que hago??? bueno, necesito ayuda, y solo hablo español y frances, y algo entiendo de ingles, gracias!!!
El sonido creo que es cuando esta en modo home, si vuela el drone o no se levanta para nada
Hello, as I see, you managed to modify the greeting line (usually "Hello, pilot"). How did you do that? Which file on the ST10+ has to be edited?
Well that was a video 'hack'. I found the "Welcome" part in strings.xml. Great observation.
+Quad Copter Thanx David?, but where to find? (which directory)
...by the way, great guide! Greetz from Germany
Where I can find it?
I can't roll back to firmware c24, do you know how? I have 29c now.
rename the file to 29.1c and try. this worked before check out yuneec-fourm.com
+Quad Copter the file is called update. Zip i can't rename that???
+Quad Copter i can't connect via usb either, see no st10 only sd card, Windows 10. 64
+hobby did you get it to update well roll back?
+Quad Copter no impossible because all the different firmware are called update.zip?!?! I can roll back the tx update that is in the folder but update.zip is on root sd card.
Here is my first version of the ST10 Menu Flow Guide. I wanted to post it so if you find something missing, spelled wrong, or comments please let me know. Version 1.0.
goo.gl/BpYKxI
Some other files.
goo.gl/zKzMXq
Live long and Fly
I'm From Dubai , recently i buy a Yuneec typhoon q500 4k drone
i didn't fly that drone even one time , its drone is problem ,
I have problem with Yuneec typhoon q500 4k cgo3 wifi problem , Its not binding
the camera wifi not showing in controller and i attached steady grip cgo3 camera its not showing wifi in mobiel
the camera showing white light only its no response light any color changes ,
controller working gimbel and drone , the camera only not showing video in controller
Whatsaap namber ........flight log,FPV.video & LOST DIR PLZ..format my card yuneec st10+ plz halp data sand ....arunstudiobahal@gmail.com
conect me.9812664204
what is the factor default password for a CGO2
Chris Bovy :check the sd for misc/wifi.... it will show the password in plain text. or just try 1234567890
What do I need to do to check the sd for Misc/ wifi
sir plz RF file q500 cotroler..st10+v01b31c
I agree with earlier comments that this is an excellent video. Thanks for taking time to upload it. It probably saved me weeks or months of drilling down into those sub-menus and most likely I would have fouled up the ST-10 trying to select some of the features. It truly is a "must-see" for newbies and all Q500 pilots.
+Lou Aymard , Thank you.
Nice living room. 🙃
There no hacks
Ronald Abalos
"a piece of computer code or information providing a quick or inelegant solution to a particular problem"
The is no manual showing most of this information.
What are you looking for?
Quad Copter I'm try disable startup up chime, ...
Ronald Abalos
Have you gained access to the file system?
Quad Copter yes
Quad Copter don't know how , someone says... Justo change file tone...
Video would be great if you didn't suck on your teeth when you take breaks from talking. So annoying. Lol.... other than that great video.
Thanks ill check it out