Excellent light and great instructions. Minor comments is make sure you push the light bar as far back as you can as it’s tight. When feeding the light cable up go through the middle space where there’s a clear opening and then feed the cable back through the foam. Also take your time disconnecting the cables and you will need to remove the zip tie on the camera (carefully). Otherwise a perfect handyman’s job and amazing product.
Thanks for the comment. This just helped me out! Unfortunately my plugs did not fit together. It seems as thought the male pins are too thick for the female connector
Hey Joe, we ship to USA and have some details on USA spec'd Rangers. If you could email us sales@altiq.com.au Attention Jake, I would love to chat further with you about this solution and upcoming Ranger Raptor products we're designing.
Hey Huskydog78, do you mean adjusting output angle? Depending how hard you torqued the bolts, you can often get a small amount of tilt through the grille for finer adjustments and the stiction of the bolts will leave it in that position permanently. This is a highly flood bias light bar, so the adjustment is not micro like our spot lights. Pro tip: Measure the height of the light bar from the ground Shine the light to a wall 10 + meters away on level ground. If the output hot spot height is higher than the light bar, it's angled up, look for a similar height. -Jake
Good instructions but takes longer than 10 minutes. Removing the front trim is tricky but once you get the tool in the right place - when ch is not well shown in video - the rest of the process is straight forward.
Probably should not solder in automotive applications due to vibration breakage over the long term. Instead, direct crimp a DT connector on the factory aux wire for proper termination and factory look.
He’s done it correct mate, those wires are from the relay which is connected to battery and aux switch, also if you look at your owners manual in the infotainment system it will give you all the info about it like wiring location/colours/ amp ratings and relay locations 👍
Can you do or do have a video for an Everest wiring installation with level 2 headlights
That would be awesome if that light bar had two ambers on each corner and center be white so you can drive in dusty bad weather conditions.
Is there a way to wire this up with an aftermarket aux, like the stedi one?
can anyone confirm if this fits 2024 ranger raptors in the USA?
confirming it DOES. i just installed it on my USA model 2024 ranger raptor
Does this fit the USA 2024 Ranger Ranger Raptor?
Excellent light and great instructions. Minor comments is make sure you push the light bar as far back as you can as it’s tight. When feeding the light cable up go through the middle space where there’s a clear opening and then feed the cable back through the foam. Also take your time disconnecting the cables and you will need to remove the zip tie on the camera (carefully). Otherwise a perfect handyman’s job and amazing product.
Thanks for the comment. This just helped me out!
Unfortunately my plugs did not fit together. It seems as thought the male pins are too thick for the female connector
Does it work the trans cooler from pw?
Do you shio in Romania?
Love it just. Great product.
Would like the know the cost. Also I have a Dec 2022 Wildtrak let me know when you get them.
Check the link in the description. $300
Will this work in the 2024 Ranger Raptor in the United States? Do you ship to the US? Will installation be exactly the same?
Hey Joe, we ship to USA and have some details on USA spec'd Rangers. If you could email us sales@altiq.com.au Attention Jake, I would love to chat further with you about this solution and upcoming Ranger Raptor products we're designing.
@@altiqauOMG just say yes or no, does it fit the US spec YES or NO
Do you shio in Romania?
Recommendations for setting beam after fitment?
Hey Huskydog78, do you mean adjusting output angle?
Depending how hard you torqued the bolts, you can often get a small amount of tilt through the grille for finer adjustments and the stiction of the bolts will leave it in that position permanently.
This is a highly flood bias light bar, so the adjustment is not micro like our spot lights.
Pro tip: Measure the height of the light bar from the ground
Shine the light to a wall 10 + meters away on level ground.
If the output hot spot height is higher than the light bar, it's angled up, look for a similar height.
-Jake
Nice, very OEM, I’d love to see a light bar that replaces the entire Ford loco with a semi curved light
Good instructions but takes longer than 10 minutes. Removing the front trim is tricky but once you get the tool in the right place - when ch is not well shown in video - the rest of the process is straight forward.
Probably should not solder in automotive applications due to vibration breakage over the long term. Instead, direct crimp a DT connector on the factory aux wire for proper termination and factory look.
Is the amperage enough? I understood that those loom leads are to operate the relay and the light bar is connected to the battery via the relay.
He’s done it correct mate, those wires are from the relay which is connected to battery and aux switch, also if you look at your owners manual in the infotainment system it will give you all the info about it like wiring location/colours/ amp ratings and relay locations 👍
Do you ship to Ranger Raptor 2023 in Brazil?
Também estou procurando. Vc conseguiu?
Hey
Do you ship to germany
Because in your shop the price are in euro
Glaub nicht , dass es passt . In Europa haben wir die Lamellen vorm Kühler .
No thanks. Blocks the intercooler which already needs to be replaced as its extremelly undersized stock.
Dude get a Fenix intercooler upgrade