ACCURATE DOOR FRAMING FOR PREHUNG INTERIOR DOOR (CC)
Вставка
- Опубліковано 16 бер 2007
- BOB SCHMIDT SHOWS YOU HOW TO ACCURATELY FRAME FOR AN INTERIOR DOOR SHOWING YOU HOW TO MEASURE A DOOR AND ALLOW FOR PROPER CLEARANCE WHILE FRAMING ALSO HOW TO DEAL WITH AN UNLEVEL FLOOR.probably the single most important part
of your framing is your door framing
00:08
proper door framing as far as installing the door go much easier
00:12
I will show you how to do that, Lets get to work.
00:20
now before you can frame for a door you have to understand door sizes,
00:24
this door in particular that we are going to be installing today is a
00:27
two six door.
00:29
does not mean twenty six inches it means 2ft 6 inches and that is a 30 inch door
00:34
in
00:34
you always frame two inches wider
00:38
than
00:38
the size of the door to allow for this
door jamb material
00:42
and to allow for shims for setting the
door
00:45
same holds true on the height a standard door is 6ft 8 in
00:49
you always frames six foot ten
00:52
along side of your opening for the door
00:54
you're always going to have two studs
00:57
the stud here that is 1 1/2 inch away from the opening
01:00
we call it the king stud
01:02
and it runs from the base plate
01:04
all the way up
01:07
to the bottom of your top plate
01:08
at the top
01:10
now this stud here
01:11
will call it the crippling comes
even with your opening and this is what you
01:15
you are going to attach your door to
01:17
and it runs from the bottom plate all
the way up to the bottom of your header
01:20
which is the top framing for the opening
01:23
now there's a reason why you always have
two studs alongside a door opening
01:27
its because
01:28
A) It has more strength for holding the
weight of the door
01:32
B)
01:33
if you nail these two studs together nice and flat on the face
01:37
It will also help keep them from twisting or bowing
01:40
and third reason is
01:42
is when you had your box, when you put
your door trim on here
01:45
It will hold your electrical box far enough away that a standard casing will fit.
01:50
if you're using a wider than standard
casing
01:53
you can always add a block to install your box on to
01:57
give you enough spacing for your trim. The
single most important thing you can do when
02:01
you're framing for your door
02:04
is make sure that this is plumb
02:06
hold the 4ft level about the center the opening
02:09
put it against the two side studs
02:11
and make sure that the bubble is as close to the dead center between those lines as you can
02:15
get
02:16
there's only a limited amount of space
that you are going to have here
02:20
to shim in behind the door if you have
this leaning too far one way or the
02:23
other
02:24
the door will not fit properly
02:26
once you're sure that your two sides are
plumb
02:29
you also have to make sure that your
header is level
02:32
now sometimes when you're building on a
basement floor and the floor is running downhill
02:38
one-side of your jamb may be kicked up higher than the other
02:41
and make sure that you make any
adjustments that you have to do to make
02:44
this level prior to hanging drywall. So
there you go
02:49
you got your width right you got your
height right you have your two side pieces
02:52
that are nice and flush with each other
that you nailed together strongly
02:56
you got a level top of plumb sides
You are ready to get some drywall on this frame
03:01
and this opening will be ready for a door. One
more thing i realized after watching
03:04
this video that we maybe you need to
know
03:06
this framing that we did for this wall
03:08
is for not bearing wall, in other words
03:12
you're going to have weight above here a
roof load or floor load you'd have to
03:16
consult an engineer to find out what size header you will need
03:21
prior
03:22
to building the wall
03:25
yea that that was pretty it, Owww
03:27
I forgot wait a second!
03:29
in case you like this video we have
some other stuff coming out you'll be
03:32
the first one to see it if you just hit the Subscribe button its over here some where. THANKS!
03:35
there's no more - Навчання та стиль
Best how-to I have ever watched. Good quality video, good instruction, saved all the bs til the end instead of putting it up front. Subscribed. keep it up.
When teaching new guys how to determine the proper width to frame a door opening I always tell them it's as simple as 1,2,3. 1- the actual door width. 2- add 2" to number 1 that's your rough opening width. 3.- add 3" to number 2 this is your header length. This way our cut man can make up our headers ahead of time without having to wait until we frame each opening. This works for bearing and non bearing walls and helps new guys begin to understand how a wall goes together.
Great quality on this video, felt like I was there myself. your cat is very cool to
Thanks for sharing Be safe and enjoy the ride!!
The stud that supports the header is actually called a "jack" stud. The cripple studs are under windows or above headers.
A little more room is better than less,this is the way I was taught.Thank for the post!---Bob
Well written and easy to understand! +++Bob
Generally speaking all framing can be done at that standard, however in a closet sometime I add additional studs on the sides to make sure I have plenty of anchoring points for shelf cleats and carry loads of closet rods.+++Bob
This is great! Thanks for another great video.
This is just great. fair play to yyou Mister Bob.
Great video! Answered my question completely! Thanks...
Nice job explaining.
From a bearing point of view I see your point ,however the less and less time our lumber stays in the kiln to dry to keep costs down lets the studs have more of a tendency to warp and twist even after installed. I believe cross nailing header 2x4 may assist in keeping door where you put it. Thanks +++Bob
another great/very helpfull video.
holy schmidt that was good - i subscribed - thanx!!
good job; covered the important stuff!
Good info, Thanks!
Thanks. I needed that.
thanks for easy to follow vid.
Subscribed. Thanks great stuff
Thanks for the Advice
good info thanks for the tips... Kev
I'm not a builder, so I should probably not even post this but I've always heard the terms "sole plate" and "top plate" instead of the term "base plate". Just an observation. Nice videos. Thank you for making them as I have to hang an exterior door pretty soon.
@mrstephenrobb Usually the floor is installed after doors are hung, however the dimensions I gave will work pre or post floor+++Bob
Yes I do. good job
here in Michigan skirtboards go along stairways, and the 2x4 along the door stud is called a lap. i suppose it could also be considered a cripple, but that's a term i usually use for the shorter 2xs under windows.
THANKS DENNIS!
We usually frame drops in and put drywall on them and then run drop ceiling flat.Not saying this is a better way to do it just the way,just seems to make a nice clean finish+++Bob
Thank you sir
The studs are the 2x4's. The middle or center of the 2x4 is exactly 16" apart. This is so 4x8 foot plywood or drywall will fit exactly. It is also building code everywhere. Studs can be closer for special purposes but generally speaking you build everything 16" on center.
@HomeRemodelWorkshop In one instance I worked on a high rise unit that the interior walls were 2 inches thick and only had a top and bottom track the balance of the entire wall was drywall panels only.+++Bob
Thanks for the comment ----Bob
@OK55OK55OK The weight of the door is transmitted through the hinge and to the anchoring points the door is attached to the side framing then to the side framing itself and to the floor. A little out of level is fine I have worked in some older homes where if you set the top framing by measuring up both sides from the floor the door would not fit.+++Bob If you kept adding weight to the door untill it gave way the top hinge would fail first that is where the majority of the stress (load) is.
I have a video called "Wall plate to concrete the start to building basement walls" and the answer is no to anything between treated bottom plate and floor. +++Bob
Nice video. Is it also standard code to install a center stud above a closet door? I have a crappy stud finder and want to find where best to anchor my pull up bar. I'm securing between my bathroom door and my closet door on top of the trim. Thx!
Thanks
@b0pN2 Two times door panel size plus 2-21/4 inches, on a standard size door height 6'-10" framing opening, pretty much same as single door with the additional door width added in,+++Bob
hi, thanks so much for this video! I am trying to install a set of French doors, frame, side panels and all. Since this is my first attempt, I was wondering if you could guide me on the following point: how does framing/measurement for a set of french doors differ from that in your video?
thanks!
Just to let you know I appeciate your comment but when you put information out there for public consumption you have to expect criticism.I have the option to allow comments or refuse them,in this case he makes valid points.I learned something so I consider this a good comment.I cannot be too thin skinned and still plan on doing this in the future. P.S Did you like the video?--- Thanks Bob
@Strankon First instinct would be to remove door frame and change framing material then re-hang door frame. +++Bob
How do you go about attaching your bottom floor joist to concrete, like on the bottom level? Is there a foam liner or anything else between your joist and the concrete?
GREAT VIDEO BOB! Hey, I am framing my 3rd car garage at the moment and am using steel studs. Do you have anything that would help me with that? Thanks again.
Rob.
You talk about making the king and cripple studs for door plumb. How do you go about that if you ar constructing the wall section on the floor, ie to be put up all at once?
@aoeah2003 If you were going with a larger span say a double door or if the wall is particularly high and the weight of the wall framing and drywall itself weighed a bit I would consider using a double with 1/2 ply between. +++Bob Thanks for watching!
@clarson0420
I have same problem, I just cut the door down to 29 3/4 with skil saw
The rest of them I'm going to frame in all new, everyone says it is much easier
@MFRoosy16 If you have the room to properly store the doors during building/remodeling then it is fine. Most projects I work on doors ,trim, cabinets, appliances will not be delivered until needed for installation+++Bob
@slhender1 Make sure it is good "by the numbers" before you raise wall then check again after wall is up and set then doublecheck door frame and adjust if needed.+++Bob Better to make the extra attempt to make plumb as possible now than later after electric and drywall.
hey bob great explanation and video...wanted to put my two cents in on the replies you've received over terminology.i have been researching door framing and have found that some terms are interchangeable,regional,or assumed understood.
P.S...Hey Nolan, where is your video?
SOME PEOPLE ALWAYS HAVE TO KNOW MORE
I have a question if you can answer in detail, how would i make a frame for a door for a (none prehung door) so standard, would i make the frame 4mm wider for 10mm higher for the 2mm gap all around and to allow for flooring any advice? thanks alot
Bob - I have seen some other videos and other people talking about double vertical headers. Is there a reason to do those or to not do those? P.S. Great videos! I am a subscriber
If your door is actually a standard door and it measures 32 inches, then you have approx. 1 1/2 inches of door jamb material, that would add up to 33 1/2 inches overall door and jamb width . Allowing for approximately 1/2 inch clearance to fit door into a 34 inch wide framed opening.
Good job Mate.
Can i ask a question...
If i was building a floor to ceiling closet (attached to an external load bearing wall, but not actually built into the wall) with double front floor to ceiling doors, would i use the same framing technique for the front of the closet?
Cheers. :-)
@MegaSpanky24 With a standard 3/4 inch jamb the framing width would be 38 inches. +++Bob
I see you are framing the height based off the plywood floor. Is the additional 2 inches in height meant to take up whatever type flooring you put down as well as shimming? If you were putting down carpet or hardwood or tile, etc. are there any calculations one should use? Thank you.
At 1:28 you said "A for holding the weight of the door." Could you explain how this weight is transmitted, and to where it is transmitted. Also, I was wondering, since you have two inches of clearance between the top of the door and the bottom of the "header", then what difference would it make if it was a little out of level.
A door in my basement opened into the laundry room, not a lot of space. I reversed this door, because it was right up against the water heater, didn't seem good. I found that this also gave a lot more space there to move around. Somehow, I got the door to stay open in the hallway automatically, maybe 1" away from the wall. Would be nice if it were closer to the wall. I want to do this for the bathroom door down there now. What's the science of getting the angle of the shims right to do this?
@Begbucks I have very little control in adsense, I will try youtube settings Thanks +++Bob
In construction there seems to be alot of ways to say the same thing. In vocational school my teacher always called the jack stud a cripple, just the way I was taught. Please feel free to let me know if the way I say things could be lost through interpretation. Thanks for watching. Bob
What should I do about a 25+3/4" door? I don't know what the people who built my house were smoking but it was too much. Door is 29+3/4"Wx79+1/3"L. Yeah, I measured that right, I've been looking at this door for two days trying to avoid having to actually re-frame the entire thing. Is that my only option?
@John100657 I could be wrong but usually the high rises I have worked in have metal framing over the concrete and the interior walls are generally metal stud framing. You may want to talk to your building super and ask if there are any units being worked on that you could go in and lay your eyes on and get a better idea what you are dealing with. Get back with me and let me know what you find out+++Bob
Hey Nolan, you sound like one of those guys who knows everything and loves to to tell other people what they are doing wrong. Just an observation:)
Hi Sam,You make a couple good points there but only so much can go into one short video.That is why I have already made a video about tips for building straight walls where I covered your concerns.I also made a video about how I like to plumb walls which is also important with hanging doors.Please check them out and let BOB know what you think+++Bob
I framed 80 in. high and 34 wide for a pre hung 32in. door, my framing wound up an inch and a half too wide and an inch and a half too low, and yes its a 32 inch door. What went wrong?
Door frame too tight, no shims needed other than at the header. It's a prehung double door, or interior french doors. got a nice close center gap at the top, but about a 16th of an inch overlap at the bottom. how should I correct this? plane the doors? or remove the door jamb and remove material from the door frame?
When accounting for the 2 additional inches, are you including 2 inches on each side or 1 inch on each side? For example, if you go with the prior, it would be a total of 4 additional inches (2 on each side) vertically.
Thank you,
@Begbucks If its not asking too much where can I install that option for my viewers? +++Bob
allows room for your flooring
great video- when he said frame the door 2 inches wider than the actual door does that mean each side or the 30 inch door is framed at 32 inches.
A 30 inch door would be framed at 32 inches total in framing width.===Bob This allows 1 1/2 inches for the door jamb and 1/2 inch for shimming.
@blgeorgio Unlike an interior door an exterior door requires a bearing header (this means it supports the weight above the door} The size of this header depends upon the width of the door and the amount of weight it needs to transfer to each side of the door. A pie barn huh. sounds like a place I would love to visit, after lunch maybe? +++Bob
And in England they call baseboard - skirtboard +++Bob
Can you tell me what the music is at the beginning of the video please!? Thanks!
LOL OK+++Bob
@orion1998is1 I have a few framing videos that will help you with this project.+++Bob
Do you mean the bottom plate of the wall or something else? +++Bob
@pc12net07 Depends on who teaches you as to the name. There are many building parts that are given different names dependent upon where you live with huge differences in other English speaking countries+++Bob
If the door is 32 inches the opening will be 34 inches+++Bob
always buy your door first so you know what your dealing with right?
You are not re-inventing the wheel here, if it is a standard size door simply find a frame with the same size door hanging in it and measure it and build a match. +++Bob
Yes, the bottom plate, my bad.
@blgeorgio
@Begbucks What kind of commercials do they have+++Bob
its not called a cripple. its called a trimmer.
Personally, I find cripples on non-bearing doors to be a huge waste of time. A faster, better way is to simply nail full length studs together, then nail in the fill blocks, then the header. MUCH faster and less waste of material and time.
If your door is a 6 ft 8 in door plus 2 inches The framed opening would be 82 inches not 80.+++Bob
yeah,right, consult an engineer. that will cost you a bunch. why do you think i'm looking at you vid.
Consult an engineer, if it is a load bearing wall. You would want your house too meet code.
Bob, you need to put a little light on the subject man. Hard to see what you're talking about. Most all of your video's are dark.