Angle Grinder: 4 Mistakes to Avoid
Вставка
- Опубліковано 20 чер 2024
- Leah from See Jane Drill shares some safety tips when using an angle grinder to grind and cut metal.
Support See Jane Drill by shopping for tools through our link on Amazon: www.amazon.com/?tag=sejadr-20
Channel: / seejanedrill
Website: www.seejanedrill.com
Facebook: / seejanedrill
Twitter: / seejanedrill
Contact us by email: leah@seejanedrill.com
See Jane Drill T-shirts, Mugs and More: shop.spreadshirt.com/seejanedrill
Disclaimer:
Due to factors beyond the control of See Jane Drill, we cannot guarantee against improper use or unauthorized modifications of this information. See Jane Drill assumes no liability for property damage or injury incurred as a result of any of the information contained in these videos. Use this information at your own risk. See Jane Drill recommends safe practices when working with tools seen or implied in our video and written content. Due to factors beyond the control of See Jane Drill, no information contained on this youtube channel, Facebook page, website and Twitter page shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this content is the sole responsibility of the user and not See Jane Drill. - Навчання та стиль
I had a lot of old pipes and rebar to cut up and from what I read ua-cam.com/users/postUgkxPDBfLu68o58Aw85O_J-zIFfjJARBhp-3 this would be the tool for the job. Since I had never used one, I watched a couple of youtube videos and I'm so glad I did. Some really good safety tips, which I followed, and this tool did a splendid job. One good thing to know is the weight of the tool puts just about the right amount of pressure on the metal I was cutting, so I didn't have to use a lot of pressure, which is more likely to jam the tool. It made fast work of my job.
I love the way this lady explains things. especially her pronunciation . very clear and deliberate.
chris pevey sexy af
In India I have seen many cases,never respect the rules.take it lightly.in workshops,lathe workshops even in famous foundries.
That's a lady???
So I will admit I did not think angle grinders could be dangerous until I used one .even wearing protective gloves and during the moment I thought the wheel was slowing down to a stop ..it was not going around very fast and it just skimmed my finger. Straight through the glove with a very slight cut ..then I realized I would have lost my finger. I would never use one again without caution ..ruthless ..tool. VERY dangerous.
i agree very clear esplications and pronunciation
I use angle grinders a lot at work. These are very important tips. Great job Leah.
Hey Jason, thanks!
I am lazy and only use face shield
@@romuloarantes7820 I would prioritize hearing protection as #1 thing to put on. It's really hearing damaging loud. It's just stupid to give up your hearing over being a cool boi. Same for your eyes. It's possible to use a grinder without safety glasses, i did that a lot when i was young, just don't have your face in line with the blade and it's kinda ok. But a doctor visit makes you quickly think otherwise about wearing safety items. Wearing gloves is just more comfortable so you don't have specks of metal or stone smacking onto your hands nonstop. Angler grinder = gloves, glasses, hearing protection, and if you're cutting a lot of stone then also definitely breathing protection.
@@romuloarantes7820 Always wear tight fitting goggles when using a grinder, the particles can go UP UNDER a face shield. An eyeball mark 2 is made of glass after all and their rubbish at seeing things out of.
@@Engineer9736 I have some 3m earplugs (not the bulky headphone style she has), it feels like they dampen the sound a lot. Are they sufficient enough to protect my hearing long term?
First time on the channel; you're a really great speaker Leah, very informative and engaging.
Thanks Kevin and I hope you come back.
seejanedrill
I hear that u can tap a disk with a screwdriver to listen for a ring and if u don't hear it that means it's bad
a vid from the- real tool review - channel
Fantastic video. I'm experienced with a variety of shop tools but new to angle grinders- a lot of tutorials are flashy or make a lot of jokes, but I really appreciate your straightforward, honest approach to tool safety. You clearly know your tools!!
i've always been an avid DIY mechanic but i've never done anything that required me to use an angle grinder up until recently. These are really good tips of what not to do and i'll be buying a face shield as soon as possible. Thanks!
Fabulous! Leah isn't patronizing and doesn't talk because she enjoys hearing herself. Everything he has to say is pertinent to the topic. I will definitely look for more of her videos!
Great tips! I absolutely agree with these specially not removing the guard. I experienced a disc breaking apart while cutting an angle iron/bar. the debris from the disc flew at high speed and chipped off part of my thumb nail and left a 2mm deep wound just below it. So never take the guard off!!!
Thank you so much! I'm sixteen and building things has been my passion for 4 years. But one thing I've always been afraid of is angle grinders (all I hear is the horror stories about them). so I'm watching all the safety videos I can and this one is one of the best!!
Thanks, and good luck with all of your projects. It's always nice to hear from young people who are interested in building things!
Thanks, Leah. Bought (and used) my first angle grinder a couple of days ago. Had to cut off 6 in. of a metal sign post. $14 for the grinder at Harbor Freight and $8 for an 8-pack of cutting wheels. Watched your video afterwards, but I used all of the safety equipment you suggested, except for the mask (did not think of that). Removed the section of pole without issue, but I went very slowly and methodically. But, even in instances where one has a high-quality grinder and attachment wheels (not Harbor Freight cheapies), this is an inherently dangerous tool. I would not want to be using this tool on a regular basis...Great video!
thanks, and I'm glad to hear that your project went well!
I just bought my first one today. Thank you for the excellent advice.
Yes, Leah is indeed a very good teacher. From Canada, thank you Leah ! !
can we talk about how great it is to finally see a woman with exceptional tool tutorials?
many thanks, Leah.
Comment at 3:12 is absolutely spot on. PPE is the last thing most people think about whereas it should be the first. I'd sooner look like a dork for 15 minutes than be scarred or disabled for life.
I couldn't agree more
I wear eye protection when SOMEONE ELSE is using this tool. Great video.
Couldn't agree more. I'd say the most important tip here.
PPE don't really make you look like a dork at all. If you're in a workshop you look pretty normal covered in PPE.
I need to start wearing a mask, because every time I grind my nose gets all clogged up with crud.
I love the way you explain things. Your tone is so encouraging and caring. When you say "you can do this", I get so encouraged. Keep being you.
Thank you for making the basics so clear. I have been using a grinder for years and yes that safety gear isn’t comfortable but so necessary.
Keep up the great content!
I've been using angle grinder for years as a handyman and welder. And only once used a cheap cut off disc but it exploded on me as it was spinning learned my lesson from it and always get decent quality discs now
Disk quality isn't sure fire way to protect yourself from detonating disks though.
Seen plenty, even had one detonate in person, scary shit.
By far, the best way to stop disks breaking is to use them properly.
You are a fantastic teacher, Leah. I don't even own an angle grinder but I love watching your tutorials. What a heck of a resource for people. Thank you so much!
you're welcome, glad you liked it! I have close family members in Boston...it's a great town!
Thank you for keeping us newbies safe! I just bought my 1st angle grinder.
Not necessary newbies. You can always hurt yourself with an angle grinder.
Thank you for the how to use the tool videos. I believe that too many people watch videos with a project in mind, only to ignore the operation. The goal of finishing the project overshadows the journey of creation. People don’t plan to get half way through a project and then go to the ER. Thanks again. Good Journey. Richie
Another great video, Leah! I never realized the danger of cheap discs. I really appreciate the info. This will definitely change how I use my angle grinder and the discs I buy. Thank you!
Also make sure you use the right disc for the right job :-)
And PIN YOUR HAIR UP if its long. Mine got caught in a mounted grinder that I had just turned off. I was just doing a simple little job, then someone spoke and I turned to hear. In less than a second my face was about 1/2 inch from the grinder. It had pulled me in quickly ! PRAISE THE LORD I was able to stop the wheel. Then my husband had to unwind my very long hair. Very scary !!! So y'all be careful. - Nice video, and good tips. Thank you for sharing.
WOW!!! I've never seen or heard that one before. Thank you for sharing your story with others. Safety first, right!
seejanedrill - even though I had turned it off, it still had a strong spin going. Had it been on, that would have tore me up. Thank you for your safety tips. I'm bad about no gear whatsoever. But these comments and testimonies have me reconsidering. Thank you.
seejanedrill ki
chicks WILL learn the hard way.
scott left That's a very stupid comment. Nothing more to say on that...
Thank you so much for sharing this serious safety information 🌹❤️
Finally someone I can learn from. Thank you! Look forward to more videos
Thanks so much for sharing your experience and thoughts about the under looked situation when using a grinder. We get so comfortable and forget common sense and logic. Thanks for reminding me and reaching out to the inexperienced users. It's time to go threw my collection of disks.
you're welcome, Gina, and thanks for writing!
Great video Leah, you've got great on camera presentation, dictation and your points are all good ones.
I'd like to add something... Safety glasses aren't enough, you need goggles that seal to the face.
A little while ago I was grinding some metal, with all the correct (or not as it turns out) safety gear. I was wearing safety glasses that go close to the face but dont quite seal it off. A small spark (debris) managed to fly out towards my neck/chin and then curved right up into my eyeball. I didnt feel any pain or discomfort at the time, so figure it was fine.
I didnt feel or notice anything till 3 days later. Had symptoms similar to conjunctivitis. Went to the doctor who said I had a speck of metal fused onto my eyeball, with a small rust ring around it.(not visible to the naked eye).
Had 2 more trips under local anaesthetic to remove the speck and then the rust ring. The pain when the anaesthetic wore off was excruciating. I was laid in a dark room, with sunglasses on an a gut full of painkillers for a day or two after each procedure...
Maybe I was just unlucky, but wanted to share this as a warning to others.
Excellent, clear explanation of the importance of being safe before you touch the switch, and as she says, err on the side of over rather than under protection when using a tool like this. The only thing I would add is the one many of the commenters below make; namely, that you be sure to tuck/tie/put away any hair, clothing or other item that could fall into the grinder and pull you into it.
Great video and extremely important subject.
OMG, you've great talent of clear speech. God bless you.
Thank you, i'm about to cut out a piece of tin drainpipe using my dad's angle grinder. And i've never used one before.. And had put it off doing it.. As scared for a few reasons.
I had already bought the safety googles, and protective safety dust face mask.
But i didn't think about buying a flip up face mask visor.. And with seeing the amount of sparks coming off, i will definitely by one.. And also buy a better protected working overall.
Good to know best not to scrimp on buying cheaper blades.. And to be aware of what's around you when using the grinder, that nothing catches fire... Great and sensible advice.. I'm glad that i clicked on your video..
How did it go?
Great easily explained video. Didn't know about buying quality discs but makes total sense. Thanks Leah.
Excellent video Leah! Great tips on safety... thank you.
"An I gotta tell ya" this woman is good stuff!
The protective guard for grinding and a protective guard for cutting are different but fitted in the same way. Angle grinders are supplied with the protective guard for grinding but the protective guard for cutting is an additional but necessary part of the safety equipment.
I was an aircraft mechanic in the Air Force and it's so nice to see another woman doing this stuff! The Air Force beat safety safety safety into us. I saw a video once where a women was drilling a hole in a piece of glass with her long hair down. At one point she shook it around like "look at me". I wanted to reach right through the screen and wring her neck because the drill sure would have had her hair got caught in it. I wanted to tell her to ALWAYS keep her hair up, for Gods sake but the comments were disabled.
Excellent! I just bought a new angle grinder and thought a safety refresher would be good. You did not disappoint. Appreciate you.
a thing i like to do is every time i use a grinder, before getting face close on the work, i turn it on full speed away from me, just to make sure the disc is still structurally sound, i had a safety class in welding school about grinders and there's so much thing that can go wrong from cheap chinese epoxy to bad batch , disc that have been weathered, bumped against something, and a disc that flies off is pretty deadly
you're absolutely right, Martin. Thanks for sharing the additional safety measure.
makes sense, and have you seen the super thin cutting discs they do now? they can so easily be damaged by putting the grinder down against something, you can push them with fingers and snap the edge off.
yup
Agreed 100%
Gotta disagree with the deadly part. The discs are made of fiber and simply don't have enough mass to penetrate a thick work jacket or gloves. A broken metal diamond disc on the other hand, that can kill you.
great video, because not everyone has someone around for guidance. And I have another couple tips for grinder safety... keep clothing items like hoodie strings and any loose clothing away from the grinder and tie back long hair well. I my long hair come out of a poorly tied pony tail and it got caught in the grinder in just seconds before I could stop the grinder to fix the problem. I was lucky I wasn't seriously injured.
patthesoundguy - My hair got caught in one, too. Very scary.
luckily im bald
Thank you for this informative video! I just bought my 1st angle grinder and was ignorantly unaware of the risks. Since I just bought it mainly as a distressor to use with wire wheels for woodworking, I was very surprised when shards of metal and sparks went flying! Wish I would have seen your video first.
Thanks Leah. Glad I watched your vid. I got mine last week, never used one before. Great safety tips.
Great vid!
A hidden hazard is that most abrasive disc medias are made of silica(essentially, beach sand; also what glass is made of).
Silicosis is a malady caused by inhaling this dust and can happen VERY quickly. It can damage your lungs. I know because it has happened to me. It still causes me respiratory issues, years later. You are essentially inhaling microscopic bits of glass and metals when grinding metals. Wear a respirator people ! Not just a dust mask and only remove it AWAY from the work area after blowing the dust off of your clothes.
Better yet, buy a face shield with a respirator built into it. Having a small fan blowing fresh air at you when grinding also keeps the nasty bits away from you. A good idea when welding too.
Many are made from aluminum oxide.
Thank you, Tommy, for sharing your personal experience
Thank you Sir.
very important tips thank you
I think you have the most informative videos on diy issues that is over looked and or avoided but certainly needed.
Thanks for sharing your expertise!
Great video as always. I'm getting rid of all my Harbor Fright disks today!
:)
:)
Also, avoid using the trigger lock as much a possible... When there is a power cut(or somebody stumbles on the cord and yanks it off the socket), you lay the grinder on the table and take your eyes off the tool, just to have it running up and lashing at you when the power is suddenly restored.
Nice video, leah!
These things really shouldn't have a trigger lock.
I just got myself an angle grinder. It is good that I check your channel for tips before I proceed as I didn't have the proper glove, and face mask that I should have. Tbanks!!
I admire your skill and your way of explanation. Keep it up ! May God bless you.
You're so right about how dangerous this tool is. I'm always cautioned about power tools but when is time to use the angle grinder I become a little safety paranoid. Always double check everything , wear my PPE and uses top quality brand name discs. My personal choice has always been NORTON. They have the know how and the experience making abrasives so why change?
Without exception, everything she said is 100% dead on correct. Excellent video!
To anyone who doubts the importance of using safe practices with an angle grinder take a moment to Google "angle grinder accident" and then view the image results.... This is a tool with the potential to cause extreme bodily harm and even leave you crippled for life. Don't operate an angle grinder when close to pets or anyone else who isn't wearing the appropriate safety equipment themselves. Few tools have the potential to reach out and seriously harm someone who's 10 feet away like an angle grinder can. The first time you have a wheel shatter at 13,000 rpm, you'll see exactly what I'm talking about.
Soknik01 i googled it. uhhh no thanks.. ill use something else lol
Thank you. Best advise!!!!!
ive never had a disk rupture, cause ive been scared of it, i check my disks for nicks and composite fraying and stuff before i use them, ive used a 9 inch grinder without a guard before with nothing on but shorts and a T shirt, better hope it doesnt kick back! right? yup, but it wont if your carefull, call me on the dumb or dangerous side but ive only ever taken care of my disk and my guard (guard if provided) and sometimes safety glasses and of course the tools themselves, ive never been hurt, same for chainsaws and stuff, keep my legs and face out of the way, make sure the chainbrake works, i guess since ive never been hurt im right where i need to be
Of all my tools, the angle grinder is the one I respect the most. Good tips!
Thanks for this man just searched images & cancelled my angle grinder off amazon! Not risking that happening ppe or not!
Another very helpful video, Leah. Your presentations are always first class.
Very nice video and presentation. Thank you so much for the thorough, concise and precise demonstration about the safety of angle grinder.
Thank you!
How does that saying goes,
“People don’t care how much you know until they know how much you care”
Seejanedrill, thank you for doing this video! Grinders are great tools but can be dangerous as you stated. I've used them at work and home for a number of years. I have had cutting wheels shatter on me while cutting steel and aluminum but thanks to a face shield, glasses, and long pants and gloves there has been no problem. Don't be an idiot folks! Wear your PPE while grinding! While wearing mine when wheels have fractured, the pieces that hit me stung like hell.
Excellent advice. Very well presented. Thanks!
You are definitely right Jane! I just love your tutorials
I agree. They are dangerous. I would add to make sure the guard is between you and the spinning disk and watch where the sparks go.
Always check the label for the max speed (RPM) of the disc and the grinder, too much speed can blow the disc apart,
what is the minimum speed of angle grinder?
Wow, thank you George, I'll make sure I do just that!
@@Mobiedicc on the label that has the model number and serial number there should also be something that looks like...
n 8500/min RPM
The "n" stands for "rated speed" on my grinder. I don't know if it's a universal symbol or specific to my manufacturer.
@@DennisMoore664 thanks for enlightened me
After reading this, I rushed straight to my new grinder and discs I used today. Relieved to be on the safe side, by chance. Thanks for the tip.
Thank you...got one recently to sharpen mower blades...took your safety advice.
Lawn looks fab now
Thank you ma'am your video is really informative and helped me get the basics of safety straight.
May you be safe and strong!
I just saw a graphic photo (FB) of a guy laying on a hospital bed with about 1/3 of a grinder wheel embedded in his mouth/jaw... It was posted by a friend of his. Definitely caused me to realize how dangerous a grinder can be...
you know, that's exactly why we made the video
Must be synchronicity - at first I couldn't make out what was embedded in the guy's mouth until I read thru the comments - then I got chills as I have recently been cutting a metal rail with only Eyewear and gloves - the shield is a requirement!
Jake Robinson - That's SCARY. I had a near experience myself. Just posted it in the comments above.
Holy COW! I'm gonna head over to Home Depot and buy a Face Sheild.. I also appreciated her telling us not to use the angle grinder (or any grinder for that matter) near a Gas container. I just bought my first Angle Grinder from Harbor Freight for $19.00 and I was cutting some metal with it and griding a rebar in my vice...down below about 5 feet away was my gas can that I use to fill my Chain Saw and Lawn Mower with!...never again.
thank you for the warning. I like trying new things but. I'am very proud of you though.Being 68 I think I'll let you young folks deal with this tool
Grandma 😍 says yes to you girls
Very good video. Thanks for keeping safety at the forefront.
Thanks, Very helpful & informative.
Yes I think it's already been mentioned but one of the most important safety precautions is to ensure you keep your hair under a hat, and also be careful of what you wear. I got my shirt cord stuck in the angle grinder once and it yanked my whole face towards the machine. If the cord hadn't snapped I would've been choked or worse, gotten the grinder in my face. Do be careful with hanging threads from clothes or baggy items.
Got a shoe lace caught in the spindle of an angle grinder when I was using it as a buffer. Fortunately I never use the lock for that reason. Plus if I dropped it with a cutting or grinding plate on, oof! I don't even want to imagine.
Whelp. My mate leant me his minus the guard. Methinks I'll buy one with a guard. 🤣
My uncle came to do some work in my house. I told him to use the gurad. He said: don't teach the priest to preach.
I still hope he lives a long life, though.
Had a grinder kickback at me yesterday while vertically cutting a tack. Got a 2 inch gash in my chest and 7 stitches. The only thing I did wrong was not having the handle attached. If I did I may have been able to hold on to the grinder, instead it flew out of my hands. 25 years experience and still learning.
Thanks for this Public Service Video! I've been thinking about getting a Grinder but your video was the first I saw that gave such great advice about the dangers. Thanks again.
Leah, I wonder if it is a good idea to wear leather gloves? Of course, they protect your fingers from hot debris, but what if they get caught by the spinning disc and rip off your fingers?
we aren't allowed to wear gloves near or on rotary equipment for the very reason you stated
It is hard for me to imagine how you would get your glove caught in the grinder in the first place, and even harder to imagine how that could be worse then getting your unprotected hand or fingers caught. What am I missing here?
Always do not use gloves (only for angle grinder)It is very dangerous.
Wrong!!! I once had one of those disks bust apart & fly off the grinder (not all that unheard of) when I wasn't wearing gloves & it nearly broke or took a finger off, Now I ALWAYS wear leather gloves using a grinder.
Wear gloves for angle grinders. Do NOT wear gloves for table saws, lathes and milling machines. Any machine that can pull you into it by the leather or canvas cloth shouldn’t be used with them. You CAN wear thin nitrile (4 mill or so) gloves to protect against oils, cutting fluids and chips, as they tear instantly if caught.
Thanks, Leah. Good stuff!
All you newbies out there, listen to this wise woman.
I spent decades in heavy construction and yet I was nearly blinded doing a quick job at home one Sunday night. I was using an angle grinder to hack through a piece of black pipe without wearing a faceshield (hey, I always wear prescription safety glasses, yeah right) when a tiny grinding spall somehow found its way to my eyeball. The eye surgeon said I was very lucky. Another millimeter over and that spall, the size of a poppyseed, would have landed on the optical center of my eyeball and I would have, painlessly, lost the sight in that eye.
Ricopolico - Thank you for sharing.
Well done Jane, thanks for making this important video, stay safe!
Great video. Thanks, Leah.
I was interested in how to use an angle grinder (or other method) to sharpen tools like a shovel, axe and/or garden shears. Most tools sold in stores are not very sharp, but tool sharpening seems to be a lost art. People buy cheap tools and throw them away. My grandfather had these files that I remember him after work everyday would clean his tools with some oily stuff from a can and sharpen them. He was a carpenter.
While it can be done a hand held angle grinder with a stone mounted in it would be a poorly controllable method of sharpening any cutting tool. Even more so for anyone without a lot of angle grinder use. Much better to use a bench grinder. And since most or all of those types of tools will be made from high carbon heat treated steel you'd want to be very careful about not over heating the tool while grinding and taking the temper out of the part. If it's getting too hot to touch you dip it in water and cool it down before grinding any more.
+Turning Point Thanks for the info!
Your welcome, the same advice as what was given about cheap angle grinder wheels apples to bench grinder wheels as well. And there is a proper procedure for mounting them so make sure the wheels identification paper is on it so the wheel doesn't get stressed while tightening the retaining nut. The wheels should be ring tested before mounting just like someone pointed out in the comments here about doing it for angle grinder disks and wheels. And I'd do some research right here on UA-cam about proper wheel selection and wheel dressing.It's not overly complicated but there are some things worth knowing that far too many don't bother to learn about.
It does take a lot more time, but if you'd rather not get a bench grinder a good Norton hand stone could sharpen most of what your likely to want to do as well. A woodworking tool dealer can offer good advice about proper wheels or stones and sell you the right ones.
+Turning Point: I have an old 1960s era bench grinder that belonged to my dad but I've never used it. I believe it is a Craftsman. I'll get it out and see if it's in decent shape. It has two wheels and holes to bolt it down. I'll take a look at some videos to see how to use it. I'm not sure if the wheels ever need replacing....I guess if they look worn. Thanks!
Hi Laura,
Worn wheels, one's that become loaded up with metal etc just need the working area restored using an industrial diamond mounted in a holder to reface the wheel. Maybe $15-$20. -If you've not used that grinder in a long time then stand well off to the side the first or better yet any time you start a grinder. If the wheels got any damage during storage they can explode at high rpms. Bench grinders are safe enough but there are some operating procedures that should be followed. The back edge of the slot in the tool rest should be adjusted in and kept within about 1/8th on an inch from the grinding wheels working face as the wheel wears down.
Great tips, I don't have a face mask but I'd wear it if I did.Goggles and gloves are a must. I know it's a no no but I rarely use the guard. I also never, again NEVER stand in the path of the blade. Or the sparks. Four fingers of my right hand are always in the path but that's unavoidable. If I absolutely have to be in the path of the blade, the guard is on. The guard on mine is a pita, and have more trouble with it on as I get crooked cause I can't see aroun the darn thing. Which brings me to why I commented, a couple of tips to add if you don't mind. 1.) Respect the grinder, but don't be scared, scared will get you killed. 2.) Don't change the blade while grinder is plugged in. 3.) Dont stand in the path of the blade4.) Don't get the blade sideways, that's how it breaks and you lose your face. (If you do get crooked, back the saw out and widen the channel) 5.) Never make cuts with the blade facing your throat, face etc.6.) Always keep firm hold of the grinder. 7.) Make sure your workpiece is secure.8.) Listen to the sound of the motor. It will tell you a lot.9.) Don't lose concentration.10.) Don't leave power tools plugged in where kids pass through.11.) Let the saw do the work12.) Plan for the best. Expect the worst.13.) Remember the 5 Ps
Very insightful video. Thank you.
Great info Leah. Thank you.
@ 0:58 and after she mentions that the angle grinder might be the most dangerous tool in the work shop, right next to the table saw. If that is the case, then why not put the angle ginder some place else??
iw63boomer . morons like you are always the most dangerous tool wherever they go...you know, on the count of being real, real stoopid
...whooosh.
iw63boomer bwahahahaha
If you don't understand that it was a joke, you are the stupid one.
hahaha... I'm not sure which is funnier, this joke, or the replies from incensed idiots who didn't get the joke! :D
It's amazing how little commonsense D.I.Y's possess when it comes to using power tools. I nearly lost an eye 30yrs ago, thanks to a lack of protection
Ross Westmore what do you mean little common sense???
@@Rhino5.0 He just wants to moan, don't mind him
Okay, officially subscribed. I've been thinking about getting an angle grinder for a while, as I'm getting into metal restoration, and I never knew at all about the chips of stuff flying off. Thanks for the knowledge.
Thank you so much for this information. All the best to you.
Lemme tell you about a mistake to avoid. Don't let your tough nylon shirt tail get tangled in the disk. Especially with a big, powerful grinder with no dead man switch.
John Dough I feel it in my stomach just imagining this - damn important tip!
that's probably why many of us prefer to do our grinding wearing only safety glasses, boots, gloves & a Kevlar jockstrap
LOL, did this shirtless and got skin burns everywhere where the sparks hit. It may even cause cancer doing it enough times.
Long-term exposure from metal skin burns and metal implanted in skin could lead to skin cancer, in particular those allergic to certain metals.
Iron seems to be the least reactive but are you sure it's pure iron? All you ever wanted to know including black testicles, LOL.
www.ganoksin.com/article/metals-safety-information/
Sure, glad you like the link. I know people whose skin reacts to gold, one of the least non reactive noble metals. You mentioned grinding plutonium, LOL. I heard from a coworker plutonium was accidentally released from a glove box, I literally sh*t in my pants. Can't say anymore, it was a non incident for the rest of us.
Another way to put the speed into perspective...it spins at 167 times every second.
Protective gear is a must. Years ago I didn't take it seriously at all and then one morning I had a piece of near molten hot steel roughly a quarter of the size of a dime flick up into my eye. I could hear it sizzling inside my head. Thankfully I didn't lose my sight in that eye but it's no longer waterproof. Water leaks in when showering or swimming *L*
oobaka1967 - Thank you for sharing your testimony. And glad to hear you came through it well.
Thank you for the video. I haven't purchased one yet because I didn't know a lot about it. I appreciate your knowledge and tips.
Thank you for posting this helpful video
Thank you so much!! I just bought one of those and I’ll be sure to heed your warning ⚠️👍👍
Let me first thank you for all this information. I will be working on a project next month and I have never used one so I will do everything you said and purchase the right proper gear
Great advice. Just went a bought an angle grinder and will heed your warnings. Thanks.
Thank you so much! Never used 1 before. Need to cut some rebar for a project and an Angle Grinder w/ a metal cutting blade was a suggested solution. Wish me luck, thanks for the tips.
Thank you very much for emphasizing the safety aspects when working with these extremely powerful instruments. I will take your recommendations and purchase the necessary safety gear.
Leah you the best. Thank God for people like you who cares about helping others. keep these videos coming.
Thanks again
you're very welcome, I'm glad to be of help
Thank you for this video! I've been a little nervous about using my grinder to cut down some rebar for a project, but I think that I might have a little more courage now!
Awesome video,Jane. Thanks for the safety tips. Not too many people mention the risks of using power tools anymore.
you're welcome, Robert, and thanks for commenting!
Very good presentation Leah, you do have the gift!
thanks, David!
Just started watching your videos. Love them. I am a construction superintendent of 30 years experience in the field, I have to wear many hats. I never stop learning because of good professionals like your self, all of what I have learned has come from other trade pro’s on the job. I started as a roofer then became a painter for 15 years then an exterior trim and siding Carpenter and now a construction superintendent for the last five years.
One thing you did forgot to mention while using a grinder especially when grinding metal. Long sleeve shirts and pants. Make them denim if possible or a heavy fabric. Will burn holes in thin fabrics as I am sure you are very aware. I’ve had the sparkle burn a few times myself.
Nasty medically treat it like a sunburn if you are unfortunate enough to get it.
Again thank you for Sharing. 👍🏽
Hey, thank you so much! I really appreciate hearing from pros like yourself!!
Two big thumbs up Leah! All these safety tips are so important. Many times I have been grinding wearing only safety glasses and you can still get debris bouncing up under them. The steel guard is imperative. Even with quality abrasives, they still can fracture when mistreated. The guard is there for a reason.
Always nice to hear from other youtube creators. I enjoyed your video on making a strop.
Thank you Leah! After years of learning from youtube, I thought it was time to put something back in. I'm just paying it forward.
Thank you Lea, great information
Excellent video. Hip-pocket training for the folks (like me) who are new to/considering buying angle grinders.
Thanks for the tips! Good video.
Thank you for the helpful tips.
Thank you so much Leah for the great tips! I like your video.