How to Build a Ford 302 Small Block - Part 7: Valvetrain
Вставка
- Опубліковано 6 жов 2024
- Today we show you exactly how to install the valve train for a Ford Windsor 302 this includes lifters, rocker arms, and pushrods. This whole series is sponsored by @SummitRacing and would not be happening without them!
Lifters: www.summitraci...
Pushrods: www.summitraci...
Rocker Arms: www.summitraci...
Loctite 565: amzn.to/3kYhoGe
Engine Assembly Lube: amzn.to/3mgprgU
Permatex Ultraslick: amzn.to/3Fa5xwU
Playlist: • How to Build a Ford 30...
Instagram: / ryansgarage408
If you have a car question ask it completely free at www.2carpros.c...
*Disclaimer: Please use all safety precautions
This series has been great for me. I'm building a 351 Stroker and the parts and steps are pretty much the same. Thanks again!
Great to hear!
I'm from Syria and I love your channel you are a legend keep the good work
Great videos, but you should always check pushrod length. No way the geometry is the same with new heads, springs and so on. Thanks for the hard work!
You'd be surprised. Our build went incredibly well and made big power. Thanks for watching!
@@2carpros But you can't skip that process on the "instruction" side. That's a roller block with a flat tappet cam. And aftermarket heads. Pushrod length should be checked when changing ONE component. You've changed many. (I did too. And a $20 pushrod length checking tool and about 20 minutes verified that stock length would be ok.)
A quick and simple method to pump the lifters full of oil is using an oil can. Just put the nozzle on the oil hole and pull the trigger a few times. This will push any air out.
Thanks again for providing all the info in this 302 Windsor video series- very helpful and well presented 👍
I'm really enjoying this series and it's timely because I'm actively building a 302. Question: can I use the same lifters you mentioned if my current lifters have a bearing to them? I like how in your valvetrain you dont have to measure for rods or any of the testing for where the rocker hits the valve. So can I use my same cam and switch to these lifters and gain the same benefits?
Nope. Use the correct lifters for your cam. If you have roller bearing can use roller bearings. Thanks for watching!
such a great vid series. just wish you would have gone with roller lifters
Thanks for watching! There is something magic about the old school flat tappet though.
Why not use roller lifters and roller cam? Maybe due to cam selection or budget?
Is there a point in your build where you first remove the inner spring of your cylinder heads to break in your cam, as the cam suppliers suggest, then replace them afterwards?😊
This was very cool to see. THANK YOU!!!
You bet!
Maybe a part number for the guide plates and rocker arm studs, please?
Looks good
Just to confirm, you set the lifters to roughly flush with the cylinder head for each piston (as shown at 3:50)? Just asking because I just watched another video where they ran the lifter all the way up then tightened. Your method intuitively makes more sense.
Correct. That's the way I do it and it works great. You just don't want any camshaft lift while you are adjusting. Thanks for watching!
“A Little Snuggening” sounds like the title of a smutty romcom. Lol!
Coming this Fall Ryan Reynolds and Sandra Bolluck play the typical odd couple in “A Little Snuggening” Rated PG-13.
Haha yeah I can see that. Thanks for watching!
Great video sharing brother
Thanks for watching!
Thanks a bunch! Very helpful. Do you happen to do a series on sbc 350's?
That's funny you mention that. We actually have a sbc 350 coming in for a full build like this in a couple months. Stay tuned! Thanks for watching!
That’ll be great! For that build, I will definitely be interested in the upgrades you do from Summit. That build will be for my own vehicle with the Vortec heads already. Really looking forward to it. I’ll turn on new notifications on the subscription. Awesome stuff!
Question can I use the same pushrods that your using for this set up with the sum-3602 cam?
So what’s next? I saw on instagram that you finished it!
Well we got to finish building this bad boy then we are strapping it to the dyno. Thanks for watching!
Why didn’t you do hydraulic roller?
How do you know if you need a 1.6F or 1.7F on the rocker arms? I’ve seen where some have both listed.
1.6 is stock.
1.7(2) is used on clevelands or if you want higher lift out of the same camshaft
Tighten this bad boy down, perfect, alrighty then, wonderful, perfect, so cheesy
I'm glad you like it!
❤
How do I get to the description you reference in Part 7?
Click the down arrow under the title of the video. Thanks for watching!
How long does those rocker last vs the stamp steel
I would say the same. They are much more efficient and have bearings instead of relying on a wear surface.
Okay thanks for the videos
Have a personal issue I’m trying to figure out
I own a mid 90s f150 5.8 speed density
Trying to figure out if I want to do a stock return or find someone with mass air to play with
Again it’s funds buying another car would take away from the actual project
Why put the lettering down ❓
Said so in the instructions. Thanks for watching!
K