The Tyre Glider is a great tool.. I tried one this afternoon........ Worked a treat. Definitely a good addition to the tool kit and small enough to carry easily on the bike. Top job all round
I found over the years of changing tires, when you get to the last bit of getting the tire on; stop and take your hand and squeeze the rest of the tire all the way around to make sure it is in the middle of the rim which is why you can get a tire on a rim. This relieves a great deal of pressure so you can complete getting the bead onto the rim no matter how or what tool you use. Thanks, I hope these will be available in the America soon.
Yes, you get any tire on every rim without force if you do it like that. It's a difference of 4+ cm circumference from outer rim to the bed of the rim.
Thanks for the demo, hard to believe how easy it looks! Clear explanation and examples much appreciated. I just fitted some 700Cx28 Pirelli Cinturato Velos and they were even tighter than my previous Schwalbe Marathons, probably 45 minutes to fit both wheels. I'm dreading a puncture with these, so I will definitely be getting one of these Tyre Gliders!
When putting the tyre on and when you are close to to the end, push the bead that is already on the rim to the centre of the rim, the "valley" in the centre of the rim is to give you the slack you need to get the last part of the bead on. The same reason all car rims have a valley on the centreline of the rim
you have to consider the valve will not let the bead into the well, so you have to start/finish AT THE VALVE so that you have the most bead in the well giving you the clearance needed to mount/dismount the tyre. I can’t understand why no tyre fitting instructional I’ve seen ever mentions this.
@@LeeTanczos presumably to create the slack required for people to invent solutions to problems that don't exist.... essentially a tool created for people to overcome incorrect technique...
I was about to write about that, but you were first.😉 No need special super tools, no need super power. Just be clever and the tire just goes in smoothly.
@@tesmith47 fair enough. I stand corrected. So, apart from easing the removal and installation of conti gators, what has this tool ever done for us? ;)
Great tool ! Despite all that, whatever tyre level you use, always push both beads down into the deeper middle of the rim to get more slack, it will all go even better ! (not too much air in the tube)
Just ordered one based on this video and whilst I don't usually have any problem getting tyres on or off I am very much looking forward to trying this and having it in my toolkit arsenal for out on the road use. Thanks Roy for the video.
Usually sceptical of UA-cam recommendations; I didn't think much of the Cycle Pal. But based on your review, I decided to give it a try. I used this to get a new standard Marathon Plus tyre onto my wheel (Mavic Ksyrium) in around 1 minute (I didn't need to use your manipulation method, but did spend a few minutes ensuring the tube was in). While these tyres are very nearly puncture-proof, they are a pain to install, especially when new - they are really tight in my experience. With levers, I would allow at least 15 minutes on a good day and expect to come out injured! This thing is great, I have ordered two more!
That’s good to hear. I will only recommend items that I am impressed with, so turn down most that are offered. I have to say that I am proud to be the first to review what I think marks a significant progression in tyre fitting. I’m really pleased that you say it’s great 👍
I run tubeless too, but on the rare occasions I do get punctures I can't seal and have to throw a tube in, tubeless rim bead hooks and tyres can be impossibly tight. Might be worth having one of these along just in case.
Great video again Roy, appreciate your effort and honesty in these reviews. I've just ordered one as well (thanks for the discount code btw), so hopefully it'll put an end to having to use three hands to change an inner tube!!
Nice idea. I hope it works for many. Best wishes Kevin! I have been using yellow Pedros levers for decades, but I know exactly how to install and remove tight, new tires, up to 20 a day, and I teach people who "can't do it" to do it.
immediately ordered after seeing 10 seconds of video... and NOW I see there is a discount code... ha!... but great find - I have great expectations of this tool ! Brilliant.
Don’t worry about the discount code, Kim, as the 100 orders went like hotcakes, so the offer ended the day after the video was published. I think it’s a bargain at that price in any case, so I hope you find it as useful as I did.
Great video showing just what an amazing tool the Tyre Glider is. I bought one a few days ago and tried it out after viewing your video. It really is so easy to use. I had a Schwalbe Marathon tyre off and back again in a couple of minutes - something I couldn't have done with conventional levers. Congratulations to the guys at Tyre Glider who have developed this.
Thanks, Peter, nice to know it’s not just me. It was invented by one man, Kevin Baker, who I shall be interviewing in the next couple of weeks. His story promises to be fascinating.
I think there's something that needs to be clarified. The video was posted on Jan 09. Your comment was posted on January 10. So how could you have bought one a few days ago? Did you buy it before viewing the video?
@@richardharris8538 Yes. I first saw it mentioned by Roy on a video he posted just before Christmas. I ordered the Glider on 4th Jan and received it on 7th Jan - great service by the way. I hope that answers your question.
Looks amazing & will definitely get one to try for myself & my dad as we were both complaining about the problems with traditional tyre levers just the other day.
Good review Roy. I’ve already got this tool and agree it’s a game changer excellent product, can’t recommend it enough and even with postage it is a fair price.
Thanks Roy, I ordered after watching and it arrived promptly. I've just spent less than 5 minutes changing my inner tube using it - after previously spending 30 mins on the "combination from hell", left with blisters on thumbs. Couldn't recommend the tyre glider enough!
Hello Roy, I bought it and tried it on my Thompson trekking bike with Schwalbe Marathon Plus and ... I am a leftie. It works perfect! I needed only seconds to take the tyre off and reinstall it. Both several times with my right and left hand ( left handed I also pulled it and it worked). thanks for the info!
Just ordered on Amazon Canada - thanks for the great review to help me knowing about this awesome tool!! I was at a race last summer and BROKE 4 tire levers trying to change a flat! Excited to never go through that again!
That’s good, Scott. If I may offer a small piece of advice. Have a good look at the Tyre Glider instructional video on their website and have dry run before you need to use it for real, as it does take a little understanding to use it correctly. But may your punctures be few 🤞😀
Thank you for the video review of this. I just got mine today. And I'm genuinely shocked at how good it is. Currently in a state of disbelief. Ha! I can even get my Tacx trainer tyre on a triban wheel, which I've never been and to do.
Well that’s sold it for me, I’ve got the trainer wheel in the garage and spent hours trying before putting the road tyre back on. Fingers crossed I’ll get some use the trainer tyre..
Thanks Roy. A great review and for that price I have got nothing to lose. Just ordered now Hopefully repairs at the side of the ride will be oh so much quicker
Thanks. Going to give one a go, although I don't have much trouble with levers...... Anything that makes life easier on the side of the road is most welcome and worth a go. :-)
Wel, I can't really believe what T saw in your video. That seems to be a great idea in turning a tyre for the future. I'm an german cyclist an I hope I can buy this tool. Thanks and greetings to all of you
No, I couldn’t believe it when I used it. I expected it to be another gadget that promised much but delivered little. The company tell me they are able to post to Germany but the cost of postage will be more.
I’ve just purchased one as I had to ride with inner tubes for a period of 3 weeks whilst waiting to set my new bike set up tubeless and you can guess I had a puncture. It is so easy to use. It was thanks to your video with Wendy that I bought it.
Yes, it really is a good tool, Heidi and I’m pleased the video helped. Ever since going tubeless I really don’t like riding my tubed bike. Here’s wishing that you don’t have to use it often 😀
So glad UA-cam bumped your vlog into my feed Roy. Brought one of these straight away and can’t wait to try it out, might even take a tyre off just for fun 😊 Must say those lanes look lovely for riding. I’m subscribed now so look forward to your interview with Kevin👍
Thank you Paul, I’m pleased to have you along. I met up with the inventor, today, to discuss an interview we will conduct on Wednesday, which should be out next week. I would definitely be taking a tyre off for fun. If nothing more it’s good to get the technique before you have to do it in anger. Also, if there is anything you would like me to cover just drop me an email.
I’ve got two of these after your vlog. I thought, another tyre removing gimmick that will end up in the bin. I own 4 bikes all tubeless. From 28c 700c to 2.0 650b. Getting my 700c Continental GP5000s and Hutchinson fusion5s can be a pain and are really stubborn. Ive now needed to update my sealant in some of my tyres so been removing and re installing my tyres. Ok. I’m convinced, the tyre glider is not a gimmick and it’s made my suffering with tyre levers into a 2 minute job. The tyres were removed from the rim with ease and re installing was so much easier. I recommend getting one or two, they have changed my opinion of tyre levers. 😊😊👍
Please note that this model is not suitable for thicker rims, such as found on some carbon wheels. This is because the groove in the tool isn’t wide enough. A new wider groove version for use with these rims is in the process of development.
I've now used the tyre glider on several occasions ' in the wild' as it were - as well as in my flat - and while I do like it very much, I've found that the thickness is a bit much and the leverage isn't quite enough to get under some very tight tyre beads and then to start the removal process. It just kept slipping out, or I wasn't strong enough to push the glider through the beginning bits of SOME tyres. I found myself using a traditional lever to get the tyre started, then using the glyder the rest of the way. Similarly, putting tyres back on - the glyder was fantastic.. but some tyres were so stiff and tight that the last bit required help from the cycle pal to lever the bead over the rim. So I now carry a tyreglider as well as at least one lever with me. - your washing up liquid suggestion is genius though - I'm going to put some in a tiny, sushi, soy sauce fish and put some in my kit!
Thanks for the update. I know that Kevin, the inventor, watches these comments so I am sure he will take your experience into account. Have a look at this video ua-cam.com/video/lS8IP6aGtK0/v-deo.html where Kevin explains the best method, which may help. The important thing is to push the glider all the way up to the tyre wall, so it is not being used as a lever. There is often the feeling that we need to lever the tyre, whereas the glider is designed not to lever. I hope this helps.
Turns out after 15,000+ miles a tube leaks profusely. Who knew. So I was in the woods, 18 degrees Fahrenheit, and I broke my composite lever. No choice but to fix it since I live off my bike. Thanks for the great review, will be ordering one. Wood floor is easier to wipe down then a white towel is to clean...keep enjoying your riding
Purchased it off this video. I gave up trying to get my Vitoria Zaffiro tyre on my fulcrum 6 wheel a few weeks ago. Tried again today with the glider and it went straight on. Unbelievable…
@@hans2574 Not a problem, just a bit stiffer material and fraction tighter, all together make it more difficult to fit compared to Maxxis for example. Tyres are great.
That is a cool solution: I'm glad he invented this.. My solution is Pirelli tires (any of them). They are not as tough as something like a Gatorskin. But they go on and off very easily. It means I can change a tire in five minuteson the side of the road. On my carbon wheels I used to struggle with Conti 5000s. Gatorskins would be utterly impossible. Not a problem with a Pirelli PZero tire.
Hello. A cool invention or, adaption! I dont ride in competition ,but for travel from place to place. Or to run errands, much the same . But when it comes to repairing tyres I no longer use tyre levers at all. What I see you doing to enable the tool , with your hands is all I have a need to do in order to remove and replace the tyres. Simply requiring some savvy massage and bending modern tyres do in fact seem to be made to come off in just such a way. Rolling the tyre will get one bead over the edge of the rim. Though replacement takes a two hands approach working around the tyre in opposite directions until both hands meet on the side opposite where the whole tyre is folded over and the last is popped on.
The problem is, Jack, that not all wheels and tyres allow this approach. I guess anything is possible with enough time and effort, but why not use a tool that make it a faster and easier process?
Oooo, well, I got mine the other day & tried it on my Roval control (MTB wheel) & the IMPOSSIBLE to get off Schwalbe Rocket Ron & couldn't budge it, so ended up making a thin metal gap holder to put in the gap, like a flat tyre lever, THEN used the 'Tyre Glider' & the tyre came off a treat. Haven't tried to get it back on that rim yet, but did put the Rocket onto an Ali rim & the tool worked very well
In all three of the bike shops that I have worked in you had to be able to take a tire on and off with just your hands. There is a method to the madness. Once learned, tools are not necisissary.
Same here, it doesn't take strength, you just got to know what you're doing. Just make sure the bead rests nicely in the valley of the rim and it'll pop right off, no silly tools required.
Definitely an interesting product. Only concern for me is that I’m uncertain whether it’ll work in my use case. More specifically, I’m not certain that I’ll be able to fit thick casing Enduro/DH tyres into the little “wing “ area on the glider. Any feedback would be appreciated from those that already had the opportunity to test the tool!
I would wait until the new model is launched in September. It will have a 5mm gap that should fit most rims. I’ll be reviewing this once available and will make sure I test it on MTB tyres t ensure the tab has enough reach.
Levers really needed some innovation, so it's good to see products like this. One tip I have is to use the dish detergent (washing up liquid), keep the wheel and tire on with the bike flipped over, then when you get to that annoying final part while putting the tire back on use the brake to push the tire on. Simply hold the brake down against the rim and spin the wheel with your other hand. The brake will act as a lever as turn the wheel. Works every time for me.
Re getting tyres off - I'm not so sure it's any better than my usual Park plastic levers., BUT, getting the tyre back on...A-MA-ZING! I could not believe I had just put the second tyre bead back on so quickly and without constantly having to poke the inner tube back in. Clipping onto the rim is a real game changer.
Looks interesting, so much so I have just ordered one. One thing to note, do not use washing up liquid as a lube for tyre fitting as it contains salts and will corrode rims. Schwalbe mamke a product called Easy Fit Mounting Fluid, comes in a small container so can easily be carried and wont corrode your rims.
I have several sets of HED Belgium + road wheels where I mount road tires up tubeless. In doing this the tire bead essentially gets “locked” onto the rim. So, the hardest (nearly impossible) part of changing a puncture while out on the road is getting the bead to break its bond with the rim. Can this product break the initial tire bead/rim connection when locked on like this in a tubeless mount manner? If yes, this would be great.
Unfortunately not. I had the same problem on a dark and freezing evening, so feel your pain. I have explained this need to the Tyre Glider inventor so he may well come up with something.
@@RideWithRoy Ok, thanks a lot for your honesty. I have a method to break the bead connection however I cannot do it on the road I need equipment back home.
I haven’t tried it on that size, Didier, so I can’t say. My MTB tyres can be changed easily with fingers so I couldn’t give it a meaningful test. I know Tyre Glider have tested on many tyres and wheels, so it would be worth emailing them for advice.
How about it on the WTB Vigilante mtb tyre. Getting bead seal to pop is really hard work and you can't get anything under the bead until its popped. I've had to resort to using g clamps, followed by standing on the tyre and pulling on the spokes, which is not advisable. In its favour the WTB tyre bead seals that well that it keeps relative good pressure if the thorns stay in the tyre.
I would recommend trying it before you need it out on the road. It’s a bit bewildering until you work out how to use it. The video I made with Wendy using it explains the technique better that in the original video.
Interesting video Roy as I have the big scissor type lever. I only recently became aware of this lever via Facebook. The criticism of this lever on there was that because it is plastic it will crack and break and the video Kevin uses to advertise it shows it being used on a tyre and wheel that you could take off and put on a tyre by hand. Kevin may be advertised to use your video because you address the issue's raised on FaceBook. You may do this yourself but I also use a pedal toe strap to grip the tyre tight on one side on the final part of the tyre. Having watched this I may buy one now. Hopefully Kevin given the money Kevin will get the money back he has invested in producing it.
Thanks. I think part of the problem with some people snapping them is if the rim is thicker than normal ie some carbon rims, so too thick for the groove. I know that Kevin is looking at tooling for this, but that’s a huge expense. In the meantime he is refunding any breakages. Another possible reason is lack of technique. It’s worth watching my video with Wendy using it. By the time I made it I understood the correct technique. Wendy is very weak wristed and managed to remove and refit a tough Marathon Plus, which I previously struggled with using levers. It’s certainly a great invention and works well for the majority of users.
I got one of these for Christmas.. it's OK. My impression of it is that it's a little better than using levers.. as someone who's used levers for 12 years or so I'd say it's maybe worth getting. You need to have really clean rims otherwise it gets stuck pretty easily.
I didn’t try it on carbon rims, Carl, as I don’t have any. However, it’s very smooth plastic with no sharp edges, so I would expect it not to damage carbon and probably be safer than tyre levers. When the bead is pulled over the rim there is more coverage of the rim than there would be with a narrow tyre lever.
I might give this a try. I have a cycle pal. I had an accident last September when I broke two fingers. I was struggling to remove the MAVIC branded tyre that came with my Mavic wheels. This device seems more portable
You might want to wait a few weeks, Bob, as a MK2 version is being launch and I’ll be making the launch video. MK2 has a wider groove that will make it fit thicker carbon rims as well as normal ones. Worth watching this video as well ua-cam.com/video/Q7hxbstDAFg/v-deo.html
Very interesting tool. I recently tried the Crankbrothers Tire Lever and it was a fail for me. I'm always looking for other options to help me with difficult tire installs. Thanks for sharing this.
That was a no-go for me. I carry "Kool Stop Tire Bead Jack, Black" which helps get the tire back on but it's bulky. I've placed an order, so we'll see how it goes.
Thanks a lot for the info, was fuuny because I have the pair of Continental gatorskin that You show on the video, it's the must difficult tire to put on a rim XD . I need to try that tool.
I was kinda excited to this item but it is not offered in the states! Could he start a kickstarter for this item ? And could you do a update on this video mentioning the kickstart project ?
Hello, Alex. The inventor is working hard at arranging distribution in the USA so I’ll ask him for an update. He is also working on a wider groove version for carbon wheels. I’ll make an update as soon as there is progress on both.
For years I've ran with a small eyedropper bottle with water and washing up liquid in, inside my saddle bag. It's saved me more than once (Gatorskin tyres).
I have Schwalbe Marathon tyres and they are a nightmare, even on nice sunny days. I now always carry Schwalbe's own blue tyre levers, which you can use to lock one end of the bead as you refit the tyre. Makes life much easier. I also carry an aluminium tyre lever and a small bottle of lubricant (one that doesn't destroy rubber, if you know what I mean!). I haven't been beaten yet - but I might just invest in Kevin's tool because my tool box isn't full yet.
Great video, I'm about to try to mount 2 new Gatorskins on my wife's mavic rims the old fashioned way....wish me luck Just ordered a couple on the strength of your video...I look forward to getting it and trying it for myself ..watch this space!
Hah! As soon as I saw that bridge over the Grantham Canal, I couldn't help trying to spot places I know. I ride that area regularly from Long Bennington. The Tyre Glider looks interesting. Thanks for the review - all three of my bikes have Gatorskins!
😀 I do make it difficult as not all shots are in sequence, but glad you spotted familiar places. I start some guided rides outside the sports ground in LB as it give newcomers a flat start. The more experienced start in Barrowby. Hopefully our paths will cross one day.
Great video and Interesting product, I’ve just ordered one to try. I dread getting a puncture on my tourer with Marathons so it will be interesting to see how it copes with that.
@@RideWithRoy Yeah those marathons are (insert swear words) to get on. I have the studded ones as I'm cycling through 15cm of fresh snow. I live in Finland and cannot buy this 😕 just tried in the web page. Will get them sent to my sister and she can forward them to me.
Interesting but not really what I was hoping for. I had a problem where the bead of the tyre would not 'unclip' from the lip on the wheel. I think this is because many new wheels are tubeless ready and so have a more pronounced lip. I was not running tubeless and the tyres were gator hardshells which are well known for being tough to get on and off any wheel but with the tubeless ready wheel I just could not get the tyre to unseat from the lip. Since then I carry a small foldable pair of pliers which I bought from Screwfix. In the event of a puncture I use the pliers with a pice of cloth between the jaws of the pliers and the tyre to protect it. It has never failed me with this tyre/wheel combination. I can get the tyre back on using normal tyre levers.
Hope to see this product picked up by larger chains in the future, I have friends who are getting back into cycling after some time and often are on long halls with gatorskins. This would make the scary flat situation less daunting.
It has created such a stir, Clark, that I am sure it will only be a matter of time. I’m interviewing the inventor for the channel, next week, so I hope he will have some news by then.
The Tyre Glider is a great tool.. I tried one this afternoon........ Worked a treat. Definitely a good addition to the tool kit and small enough to carry easily on the bike. Top job all round
Great suggestion! Ordered one immediately!
I found over the years of changing tires, when you get to the last bit of getting the tire on; stop and take your hand and squeeze the rest of the tire all the way around to make sure it is in the middle of the rim which is why you can get a tire on a rim. This relieves a great deal of pressure so you can complete getting the bead onto the rim no matter how or what tool you use. Thanks, I hope these will be available in the America soon.
Yes, you still need to do that with this tool, Greg. Tye inventor is currently discussing American distribution so hopefully available quite soon.
Yes, you get any tire on every rim without force if you do it like that. It's a difference of 4+ cm circumference from outer rim to the bed of the rim.
Thanks for the demo, hard to believe how easy it looks! Clear explanation and examples much appreciated.
I just fitted some 700Cx28 Pirelli Cinturato Velos and they were even tighter than my previous Schwalbe Marathons, probably 45 minutes to fit both wheels. I'm dreading a puncture with these, so I will definitely be getting one of these Tyre Gliders!
When putting the tyre on and when you are close to to the end, push the bead that is already on the rim to the centre of the rim, the "valley" in the centre of the rim is to give you the slack you need to get the last part of the bead on. The same reason all car rims have a valley on the centreline of the rim
you have to consider the valve will not let the bead into the well, so you have to start/finish AT THE VALVE so that you have the most bead in the well giving you the clearance needed to mount/dismount the tyre. I can’t understand why no tyre fitting instructional I’ve seen ever mentions this.
@@LeeTanczos presumably to create the slack required for people to invent solutions to problems that don't exist.... essentially a tool created for people to overcome incorrect technique...
I was about to write about that, but you were first.😉 No need special super tools, no need super power. Just be clever and the tire just goes in smoothly.
@@belgoblax1596 not really, conti gators are notorious tight fit!
@@tesmith47 fair enough. I stand corrected.
So, apart from easing the removal and installation of conti gators, what has this tool ever done for us? ;)
That was the most tense tire changing experience I ever saw thanks to the music at 7:50 😅
😂😂
Great tool ! Despite all that, whatever tyre level you use, always push both beads down into the deeper middle of the rim to get more slack, it will all go even better ! (not too much air in the tube)
Game changer. I have tried this on 3 different wheels worked like magic.
Arrived, works a treat, I'm buying extras for spares and gifts.
Absolute game changer!
Just ordered one based on this video and whilst I don't usually have any problem getting tyres on or off I am very much looking forward to trying this and having it in my toolkit arsenal for out on the road use. Thanks Roy for the video.
My only suggestion, Rachael, is that you get used to using it at home, before needing it for real. Once you get the technique you’ll never look back.
@@RideWithRoy Will do Roy. It looks great. Subscribed.
@rachael8742 thanks, Rachael, even better 😀
Usually sceptical of UA-cam recommendations; I didn't think much of the Cycle Pal. But based on your review, I decided to give it a try. I used this to get a new standard Marathon Plus tyre onto my wheel (Mavic Ksyrium) in around 1 minute (I didn't need to use your manipulation method, but did spend a few minutes ensuring the tube was in). While these tyres are very nearly puncture-proof, they are a pain to install, especially when new - they are really tight in my experience. With levers, I would allow at least 15 minutes on a good day and expect to come out injured! This thing is great, I have ordered two more!
That’s good to hear. I will only recommend items that I am impressed with, so turn down most that are offered. I have to say that I am proud to be the first to review what I think marks a significant progression in tyre fitting. I’m really pleased that you say it’s great 👍
I would come out of that job needing either therapy or absolution.
Looks like a great tool that has arrived late to the party. I've gone tubeless and haven't had a flat tyre in 3 years. Cheers
Ha, but those tyres have to come off at some point dude!
Unable to see the link.
I run tubeless too, but on the rare occasions I do get punctures I can't seal and have to throw a tube in, tubeless rim bead hooks and tyres can be impossibly tight. Might be worth having one of these along just in case.
@@charlessharpe1345 it’s in the demotion dropdown below, Charles, but here is it tyreglider.co.uk
Great video again Roy, appreciate your effort and honesty in these reviews. I've just ordered one as well (thanks for the discount code btw), so hopefully it'll put an end to having to use three hands to change an inner tube!!
Nice idea. I hope it works for many. Best wishes Kevin!
I have been using yellow Pedros levers for decades, but I know exactly how to install and remove tight, new tires, up to 20 a day, and I teach people who "can't do it" to do it.
Bought 2 of These wonders,What a game changer,tyre off,New innertube in tyre back on,less than 5 minutes. Well worth the money.
immediately ordered after seeing 10 seconds of video... and NOW I see there is a discount code... ha!... but great find - I have great expectations of this tool ! Brilliant.
Don’t worry about the discount code, Kim, as the 100 orders went like hotcakes, so the offer ended the day after the video was published. I think it’s a bargain at that price in any case, so I hope you find it as useful as I did.
I just ordered two of these things after watching this and looking at the reviews. Thanks for making me aware of it!
Great video showing just what an amazing tool the Tyre Glider is. I bought one a few days ago and tried it out after viewing your video. It really is so easy to use. I had a Schwalbe Marathon tyre off and back again in a couple of minutes - something I couldn't have done with conventional levers. Congratulations to the guys at Tyre Glider who have developed this.
Thanks, Peter, nice to know it’s not just me. It was invented by one man, Kevin Baker, who I shall be interviewing in the next couple of weeks. His story promises to be fascinating.
I think there's something that needs to be clarified. The video was posted on Jan 09. Your comment was posted on January 10. So how could you have bought one a few days ago? Did you buy it before viewing the video?
@@richardharris8538 Yes. I first saw it mentioned by Roy on a video he posted just before Christmas. I ordered the Glider on 4th Jan and received it on 7th Jan - great service by the way. I hope that answers your question.
And to add to Peter’s comment, Richard, it has been available since late late December but hadn’t been publicised.
@@petermilner2996 Thanks, Peter.
Looks amazing & will definitely get one to try for myself & my dad as we were both complaining about the problems with traditional tyre levers just the other day.
Thanks Roy.
When fitting a tyre, regardless of the tools used, it helps to warm it up and lube it.
Cue the chortles from the Viz crowd down the back.
Thanks, Chris. I did my test cold so it replicated on the road conditions.
Good review Roy. I’ve already got this tool and agree it’s a game changer excellent product, can’t recommend it enough and even with postage it is a fair price.
That’s good to know, glad it’s not just me. I also took it round for Paul Green to try and he was impressed.
Thanks Roy, I ordered after watching and it arrived promptly. I've just spent less than 5 minutes changing my inner tube using it - after previously spending 30 mins on the "combination from hell", left with blisters on thumbs. Couldn't recommend the tyre glider enough!
Brilliant Tom!
Thanks Roy. Immediate purchase. Looks fantastic and can’t wait to try it out. Cheers
I hope you don’t need it too often, David 😀
Hello Roy, I bought it and tried it on my Thompson trekking bike with Schwalbe Marathon Plus and ... I am a leftie. It works perfect! I needed only seconds to take the tyre off and reinstall it. Both several times with my right and left hand ( left handed I also pulled it and it worked). thanks for the info!
To Kevin: a leftie, for the left handed
Thanks so much. The tools you describe are exactly what I've been needing to make my riding (and changing flats) more enjoyable!
Just ordered on Amazon Canada - thanks for the great review to help me knowing about this awesome tool!! I was at a race last summer and BROKE 4 tire levers trying to change a flat! Excited to never go through that again!
That’s good, Scott. If I may offer a small piece of advice. Have a good look at the Tyre Glider instructional video on their website and have dry run before you need to use it for real, as it does take a little understanding to use it correctly. But may your punctures be few 🤞😀
Had one for a few weeks and find it superb. First job was changing two Innertubes in Marathons without any problems. Super piece of kit.
Thank you for the video review of this. I just got mine today. And I'm genuinely shocked at how good it is. Currently in a state of disbelief. Ha! I can even get my Tacx trainer tyre on a triban wheel, which I've never been and to do.
That’s good to hear, Richard, thanks for commenting.
Well that’s sold it for me, I’ve got the trainer wheel in the garage and spent hours trying before putting the road tyre back on. Fingers crossed I’ll get some use the trainer tyre..
@@RayHayHay if it's super tight just have to watch out for pinching the inner tube.
Thanks Roy. A great review and for that price I have got nothing to lose. Just ordered now
Hopefully repairs at the side of the ride will be oh so much quicker
no more pinching tubes with levers. Brilliant!
Thanks. Going to give one a go, although I don't have much trouble with levers...... Anything that makes life easier on the side of the road is most welcome and worth a go. :-)
Wel, I can't really believe what T saw in your video. That seems to be a great idea in turning a tyre for the future. I'm an german cyclist an I hope I can buy this tool. Thanks and greetings to all of you
No, I couldn’t believe it when I used it. I expected it to be another gadget that promised much but delivered little. The company tell me they are able to post to Germany but the cost of postage will be more.
I’ve just purchased one as I had to ride with inner tubes for a period of 3 weeks whilst waiting to set my new bike set up tubeless and you can guess I had a puncture. It is so easy to use. It was thanks to your video with Wendy that I bought it.
Yes, it really is a good tool, Heidi and I’m pleased the video helped. Ever since going tubeless I really don’t like riding my tubed bike. Here’s wishing that you don’t have to use it often 😀
So glad UA-cam bumped your vlog into my feed Roy. Brought one of these straight away and can’t wait to try it out, might even take a tyre off just for fun 😊 Must say those lanes look lovely for riding. I’m subscribed now so look forward to your interview with Kevin👍
Thank you Paul, I’m pleased to have you along. I met up with the inventor, today, to discuss an interview we will conduct on Wednesday, which should be out next week. I would definitely be taking a tyre off for fun. If nothing more it’s good to get the technique before you have to do it in anger. Also, if there is anything you would like me to cover just drop me an email.
I’ve got two of these after your vlog.
I thought, another tyre removing gimmick that will end up in the bin.
I own 4 bikes all tubeless. From 28c 700c to 2.0 650b. Getting my 700c Continental GP5000s and Hutchinson fusion5s can be a pain and are really stubborn.
Ive now needed to update my sealant in some of my tyres so been removing and re installing my tyres.
Ok. I’m convinced, the tyre glider is not a gimmick and it’s made my suffering with tyre levers into a 2 minute job. The tyres were removed from the rim with ease and re installing was so much easier.
I recommend getting one or two, they have changed my opinion of tyre levers. 😊😊👍
Thanks for that update, always good to have my opinion reinforced 👍
the minute you showed the device, it totally makes sense to me. Having done 3D modeling and printing, that design seems obvious. Brilliant invention.
Please note that this model is not suitable for thicker rims, such as found on some carbon wheels. This is because the groove in the tool isn’t wide enough. A new wider groove version for use with these rims is in the process of development.
Can we be put on a waiting list for the carbon wheel version?
You could email Kevin to ask. He has also agreed that I will announce it here, Mike. I believe it's quite close
Thanks for the review and discount code for the product Roy, looks just the job..👍
Thank you very much Roy, for this video. I buy 4 of this smart product. (from Italy...)
Thanks, Roy. Just ordered one in my continuing effort to solve the clincher tyre on tubeless-ready wheel conundrum.
It won’t break the bead away, unfortunately, Keith, I had to use a flat screwdriver for that, but once clear it works a treat.
I've now used the tyre glider on several occasions ' in the wild' as it were - as well as in my flat - and while I do like it very much, I've found that the thickness is a bit much and the leverage isn't quite enough to get under some very tight tyre beads and then to start the removal process. It just kept slipping out, or I wasn't strong enough to push the glider through the beginning bits of SOME tyres. I found myself using a traditional lever to get the tyre started, then using the glyder the rest of the way. Similarly, putting tyres back on - the glyder was fantastic.. but some tyres were so stiff and tight that the last bit required help from the cycle pal to lever the bead over the rim. So I now carry a tyreglider as well as at least one lever with me. - your washing up liquid suggestion is genius though - I'm going to put some in a tiny, sushi, soy sauce fish and put some in my kit!
Thanks for the update. I know that Kevin, the inventor, watches these comments so I am sure he will take your experience into account. Have a look at this video ua-cam.com/video/lS8IP6aGtK0/v-deo.html where Kevin explains the best method, which may help. The important thing is to push the glider all the way up to the tyre wall, so it is not being used as a lever. There is often the feeling that we need to lever the tyre, whereas the glider is designed not to lever. I hope this helps.
Turns out after 15,000+ miles a tube leaks profusely. Who knew. So I was in the woods, 18 degrees Fahrenheit, and I broke my composite lever. No choice but to fix it since I live off my bike.
Thanks for the great review, will be ordering one. Wood floor is easier to wipe down then a white towel is to clean...keep enjoying your riding
Purchased it off this video. I gave up trying to get my Vitoria Zaffiro tyre on my fulcrum 6 wheel a few weeks ago. Tried again today with the glider and it went straight on. Unbelievable…
That’s great to hear. It’s always a worry recommending something as others might not be as successful. Thanks for sharing 👍
Is that a general problem with Vittoria? Got my first set just before winter and my hands looked like after a fight with a cat after fitting them.
@@hans2574 Not a problem, just a bit stiffer material and fraction tighter, all together make it more difficult to fit compared to Maxxis for example. Tyres are great.
@@hans2574 just spray some water onto your tire lever, an if you have scratches onto your tire lever was water mix with soap
@@vileasphunk7789 Thank you for the advice!
That is a cool solution: I'm glad he invented this.. My solution is Pirelli tires (any of them). They are not as tough as something like a Gatorskin. But they go on and off very easily. It means I can change a tire in five minuteson the side of the road. On my carbon wheels I used to struggle with Conti 5000s. Gatorskins would be utterly impossible. Not a problem with a Pirelli PZero tire.
Second this comment. I am running tubeless Pirellis on all my bikes now.
Hello. A cool invention or, adaption! I dont ride in competition ,but for travel from place to place. Or to run errands, much the same . But when it comes to repairing tyres I no longer use tyre levers at all. What I see you doing to enable the tool , with your hands is all I have a need to do in order to remove and replace the tyres. Simply requiring some savvy massage and bending modern tyres do in fact seem to be made to come off in just such a way. Rolling the tyre will get one bead over the edge of the rim. Though replacement takes a two hands approach working around the tyre in opposite directions until both hands meet on the side opposite where the whole tyre is folded over and the last is popped on.
The problem is, Jack, that not all wheels and tyres allow this approach. I guess anything is possible with enough time and effort, but why not use a tool that make it a faster and easier process?
Great video - thanks for the level of detail.
Oooo, well, I got mine the other day & tried it on my Roval control (MTB wheel) & the IMPOSSIBLE to get off Schwalbe Rocket Ron & couldn't budge it, so ended up making a thin metal gap holder to put in the gap, like a flat tyre lever, THEN used the 'Tyre Glider' & the tyre came off a treat. Haven't tried to get it back on that rim yet, but did put the Rocket onto an Ali rim & the tool worked very well
Patent that, Mike’ before Kevin does 😀
Best cycling accessory I have bought. I got a 2nd just in case I manage to lose one😁. Makes tyre removal and refitting a doddle.
I missed out on the discount, but just ordered one anyway. I did have a thought though, is it easy to use left handed?
Yes, Rob. We had this question earlier. The inventor is left handed so told me that you simply reverse the tool and pull instead of push.
Brilliant , many thanks, i can see a new purchase here.
In all three of the bike shops that I have worked in you had to be able to take a tire on and off with just your hands. There is a method to the madness. Once learned, tools are not necisissary.
That’s a great skill to have, Dave, but us mere mortals do struggle.
The old thumbs of steel 👍
There should be a superhero called that 😂
Same here, it doesn't take strength, you just got to know what you're doing. Just make sure the bead rests nicely in the valley of the rim and it'll pop right off, no silly tools required.
You could pay for that as arthritic hands in your old age. That's a preventable industrial injury. Use the tool.
Thanks for sharing this Roy, I've just ordered 4 for myself and my mates, hope it will be on it's way to Malaysia soon.
Another great video Roy, I'll certainly be ordering one, many thanks.
Thanks, Peter, you won’t be disappointed.
Crumbs your cycling has got fast! Have ordered to give a try!
I’d had double Weetabix that day 😀
I'm still admiring that masonry
Definitely an interesting product. Only concern for me is that I’m uncertain whether it’ll work in my use case. More specifically, I’m not certain that I’ll be able to fit thick casing Enduro/DH tyres into the little “wing “ area on the glider. Any feedback would be appreciated from those that already had the opportunity to test the tool!
I'd like to know the same. Would this work for tires like the Maxxis Minion or Assegai? I'd totally get one if it works.
I would wait until the new model is launched in September. It will have a 5mm gap that should fit most rims. I’ll be reviewing this once available and will make sure I test it on MTB tyres t ensure the tab has enough reach.
Really impressed with your reverse riding abilities @Ride With Roy
😂I was waiting for someone to spot that, Neil😂😂😂😂😂
Levers really needed some innovation, so it's good to see products like this. One tip I have is to use the dish detergent (washing up liquid), keep the wheel and tire on with the bike flipped over, then when you get to that annoying final part while putting the tire back on use the brake to push the tire on. Simply hold the brake down against the rim and spin the wheel with your other hand. The brake will act as a lever as turn the wheel. Works every time for me.
Thanks for the recommendation…just ordered one from Rehook
Great vid , thanks Roy . Best wishes.
Excellent review.
Subscribed and ordered the tool 👍🏼
Looks good Roy, i will be getting one of these.
Looks good roy. Lots of video at the end there- I was expecting you to puncture just before you get home 🤣🤣🤣
😂😂 so was I. I was down a thorny track today and expected to use it for real.
@@RideWithRoy bet you dont get one for ages now 🤣🤣🤣🤣🤣 not a bad thing though
Re getting tyres off - I'm not so sure it's any better than my usual Park plastic levers., BUT, getting the tyre back on...A-MA-ZING! I could not believe I had just put the second tyre bead back on so quickly and without constantly having to poke the inner tube back in. Clipping onto the rim is a real game changer.
I'm running 700 x 45 Schwalbe Marathon and they are an absolute BEAST to get on and off. Maybe I will give this a try. Thanks!!
Depends on the rim. Mavic rims are a sod with Matathons, but with the original rims on my Super Galaxy, no problem - !
@@simongee8928 I have Velocity Cliffhangers and it’s very tough. I’m thinking of going tubeless soon.
Looks interesting, so much so I have just ordered one. One thing to note, do not use washing up liquid as a lube for tyre fitting as it contains salts and will corrode rims. Schwalbe mamke a product called Easy Fit Mounting Fluid, comes in a small container so can easily be carried and wont corrode your rims.
Thanks for that, great advice 👍
I have several sets of HED Belgium + road wheels where I mount road tires up tubeless. In doing this the tire bead essentially gets “locked” onto the rim. So, the hardest (nearly impossible) part of changing a puncture while out on the road is getting the bead to break its bond with the rim. Can this product break the initial tire bead/rim connection when locked on like this in a tubeless mount manner? If yes, this would be great.
Unfortunately not. I had the same problem on a dark and freezing evening, so feel your pain. I have explained this need to the Tyre Glider inventor so he may well come up with something.
@@RideWithRoy Ok, thanks a lot for your honesty. I have a method to break the bead connection however I cannot do it on the road I need equipment back home.
Looks like a good little tool that.
Never bought any tyre levers always used a teaspoon or 2
Hello, does it work well with DH 27.5x 2.50 Mountain Bike tires? I would like to test this product. 🤔
I haven’t tried it on that size, Didier, so I can’t say. My MTB tyres can be changed easily with fingers so I couldn’t give it a meaningful test. I know Tyre Glider have tested on many tyres and wheels, so it would be worth emailing them for advice.
How about it on the WTB Vigilante mtb tyre. Getting bead seal to pop is really hard work and you can't get anything under the bead until its popped. I've had to resort to using g clamps, followed by standing on the tyre and pulling on the spokes, which is not advisable.
In its favour the WTB tyre bead seals that well that it keeps relative good pressure if the thorns stay in the tyre.
Yes, unfortunately this tool doesn’t help to break a stubborn bead. I’ve suggested to Kevin he invent something - but until then it’s the G clamp 😀
That looks really interesting I will have to give one of them a try 👍
Looks great, will wait for it to become available in USA.
Looks impressive, ordered mine 👍🏽
I would recommend trying it before you need it out on the road. It’s a bit bewildering until you work out how to use it. The video I made with Wendy using it explains the technique better that in the original video.
Cheers, Roy. Just ordered one.
I've just bought one, as I use Marathon plus tyres, looking forward to using it☺
Don’t wait for a flat, Iain, give it a go now 😀
It looks like it functions well! I need to get one .. have been the victim of trying to fix a puncture with a Gatorskin!
His voice is absolutely magical 😊
😂😂😂
Just ordered one, thanks Roy
Interesting video Roy as I have the big scissor type lever. I only recently became aware of this lever via Facebook. The criticism of this lever on there was that because it is plastic it will crack and break and the video Kevin uses to advertise it shows it being used on a tyre and wheel that you could take off and put on a tyre by hand. Kevin may be advertised to use your video because you address the issue's raised on FaceBook. You may do this yourself but I also use a pedal toe strap to grip the tyre tight on one side on the final part of the tyre. Having watched this I may buy one now. Hopefully Kevin given the money Kevin will get the money back he has invested in producing it.
Thanks. I think part of the problem with some people snapping them is if the rim is thicker than normal ie some carbon rims, so too thick for the groove. I know that Kevin is looking at tooling for this, but that’s a huge expense. In the meantime he is refunding any breakages. Another possible reason is lack of technique. It’s worth watching my video with Wendy using it. By the time I made it I understood the correct technique. Wendy is very weak wristed and managed to remove and refit a tough Marathon Plus, which I previously struggled with using levers. It’s certainly a great invention and works well for the majority of users.
@@RideWithRoy Thanks Roy, Ted
I got one of these for Christmas.. it's OK. My impression of it is that it's a little better than using levers.. as someone who's used levers for 12 years or so I'd say it's maybe worth getting. You need to have really clean rims otherwise it gets stuck pretty easily.
Great video, and it looks great, but could I just ask what's it like on carbon rims (disc brake) will it scratch the wheel when removing?
I didn’t try it on carbon rims, Carl, as I don’t have any. However, it’s very smooth plastic with no sharp edges, so I would expect it not to damage carbon and probably be safer than tyre levers. When the bead is pulled over the rim there is more coverage of the rim than there would be with a narrow tyre lever.
@@RideWithRoy ahhh thank you, no worries, I think for the money I might just get a couple to try anyway 👍 anything to save time when out is a bonus.
I might give this a try. I have a cycle pal. I had an accident last September when I broke two fingers.
I was struggling to remove the MAVIC branded tyre that came with my Mavic wheels.
This device seems more portable
You might want to wait a few weeks, Bob, as a MK2 version is being launch and I’ll be making the launch video. MK2 has a wider groove that will make it fit thicker carbon rims as well as normal ones. Worth watching this video as well ua-cam.com/video/Q7hxbstDAFg/v-deo.html
Love it, buddy, bought 8 from Amazon for my buddies at Delemere Cycle Club....
I hope you don’t need to use them too often 🤞👍
Very interesting tool. I recently tried the Crankbrothers Tire Lever and it was a fail for me. I'm always looking for other options to help me with difficult tire installs. Thanks for sharing this.
That was a no-go for me. I carry "Kool Stop Tire Bead Jack, Black" which helps get the tire back on but it's bulky. I've placed an order, so we'll see how it goes.
Thanks a lot for the info, was fuuny because I have the pair of Continental gatorskin that You show on the video, it's the must difficult tire to put on a rim XD . I need to try that tool.
I was kinda excited to this item but it is not offered in the states! Could he start a kickstarter for this item ? And could you do a update on this video mentioning the kickstart project ?
Hello, Alex. The inventor is working hard at arranging distribution in the USA so I’ll ask him for an update. He is also working on a wider groove version for carbon wheels. I’ll make an update as soon as there is progress on both.
@@RideWithRoy thanks 🙏🏼
For years I've ran with a small eyedropper bottle with water and washing up liquid in, inside my saddle bag. It's saved me more than once (Gatorskin tyres).
Just stumbled on this,amazing bit of kit,ordered 🙄
I have Schwalbe Marathon tyres and they are a nightmare, even on nice sunny days. I now always carry Schwalbe's own blue tyre levers, which you can use to lock one end of the bead as you refit the tyre. Makes life much easier. I also carry an aluminium tyre lever and a small bottle of lubricant (one that doesn't destroy rubber, if you know what I mean!). I haven't been beaten yet - but I might just invest in Kevin's tool because my tool box isn't full yet.
I knew what you meant 😂
thank you Roy, ordered off your video. So easy to use
Great video, I'm about to try to mount 2 new Gatorskins on my wife's mavic rims the old fashioned way....wish me luck
Just ordered a couple on the strength of your video...I look forward to getting it and trying it for myself ..watch this space!
🩹🩹🩹🩹🤞
I need this. Definitely buying one
Hah! As soon as I saw that bridge over the Grantham Canal, I couldn't help trying to spot places I know. I ride that area regularly from Long Bennington. The Tyre Glider looks interesting. Thanks for the review - all three of my bikes have Gatorskins!
😀 I do make it difficult as not all shots are in sequence, but glad you spotted familiar places. I start some guided rides outside the sports ground in LB as it give newcomers a flat start. The more experienced start in Barrowby. Hopefully our paths will cross one day.
Great video and Interesting product, I’ve just ordered one to try. I dread getting a puncture on my tourer with Marathons so it will be interesting to see how it copes with that.
Let’s us know how you get on. I found that on a thick tyre it benefitted from a little lubricant on that last bit.
Wow, it worked on the Marathon.!!!! I fit them every winter and always mess my hands up. I’m buying one of these now.!!! 🙏
It did take a bit of work on the last part, Dean, but way easier than normal and a big saving on plasters 👍
@@RideWithRoy Yeah those marathons are (insert swear words) to get on. I have the studded ones as I'm cycling through 15cm of fresh snow. I live in Finland and cannot buy this 😕 just tried in the web page. Will get them sent to my sister and she can forward them to me.
If you email them they will give you a postal charge. Some subscribers in Australia, Canada and USA have just ordered.
@@RideWithRoy superb, will do that now 🙏🙌
great video Roy, just ordered 1.
Let me know what you think, Michael.
Interesting but not really what I was hoping for. I had a problem where the bead of the tyre would not 'unclip' from the lip on the wheel. I think this is because many new wheels are tubeless ready and so have a more pronounced lip. I was not running tubeless and the tyres were gator hardshells which are well known for being tough to get on and off any wheel but with the tubeless ready wheel I just could not get the tyre to unseat from the lip. Since then I carry a small foldable pair of pliers which I bought from Screwfix. In the event of a puncture I use the pliers with a pice of cloth between the jaws of the pliers and the tyre to protect it. It has never failed me with this tyre/wheel combination. I can get the tyre back on using normal tyre levers.
Hope to see this product picked up by larger chains in the future, I have friends who are getting back into cycling after some time and often are on long halls with gatorskins. This would make the scary flat situation less daunting.
It has created such a stir, Clark, that I am sure it will only be a matter of time. I’m interviewing the inventor for the channel, next week, so I hope he will have some news by then.
It’s available in the US thru Amazon and I ordered one….it is a game changer tire off and back on in just a few minutes.