Hi it's mostly guess work and experience i guess for the capacitor value. You can measure those in the other rails i guess and try. Or sometimes you lucky and find the circuit diagram. Yep unfortunately lots of guess 😂
I think he just left out the capacitor. The capacitor is there to reduce any noise on the power from affecting the signal. Any capacitor value of the same order of magnitude should suffice if you find you need the filtering.
Sir very informative video, I have vertical line's for first 4 minutes and slowly freezing picture with audio starts then in another minute clear picture with proper audio comes from LG-47LA6200 TV (3D model). I kindly advise, all voltages are okay from T-Con board.
Hi, at 5:25, not really sure of their name, but there are golden tapes with traces soldered at the top of the board, one of them on my tv got detached, is it possible to solder it again on the board?
Hello, how are you? I brought an LG 37lg606 ur LCD TV for repair. The inverter board had a problem and the TV only stays on standby. A fuse and MOSFET number 8447 were burned on the inverter board. I replaced it and replaced the MOSFET with 45n03. Now the TV turns on. The image fills the problem. Is there a replacement for MOSFET or not? Thank you for your guidance. 🙏🙏🙏🙏
@@tevzTVTevatronics Yes, the picture is perfect, when I use MOSFET 45n03, the picture fills up and today I used another MOSFET 50n06 and the picture came, but the picture gets dark in the middle, it doesn't fill up anymore.
Hello, considering the connection of many parts, how did you determine that this capacitor has a connection? And why didn't you assemble that capacitor
Thus capacitors are connected in parallel so they like all are shorted. do you mean to desolder the capacitor? I desolder the lowest ohm reading and that the suspected shorted capacitor.
@@tevzTVTevatronics Thank you for your response So, we take the ohmic capacitors in places where the ohms are much lower than in other places, if we have them, is the part suspected to be connected
Nice. tanong lng po. Meron po kami na LG 55in tv, kaya pa po ba marepair ang lcd panel na may open/shorted circuit? bali ni-repair po ng technician at ginawa ay ung tape method.. pero kaya pa po ba tlga magawa ung pinaka sira nun na circuit?
My samsung 32" led tv backlight turns on and off when the power supply or card is touching the metal of the led. But when i lift both boards then the backlight turns on. And there are colored vertical lines on whole screen.
What a genius engineer
With every video you make I learn something new and I appreciate how you show your knowledge for all to use,true master.
This video teach me how to get short pf very easily way. Superb work
Nice tutorial sir for repairing television thank you for sharing this video
Thanks for watching
indeed i have leaned a lot from your channels,keep it up
Thanks sir for sharing your ideas👍
Good information sir 🌹
Nice video and very informative
🤗😊love this work
Thank you! 😊
Same to
thanks again for sharing sir god bless🙏
Thank you Sir,you are the best teacher.😊
Hai it's fantastic fuilt 👌👌👌👌👍👍👍👍
Hello idol magandang buhay thanks for sharing this
Good job papa ❤️
thanks kaTech.. big help to improve troubleshooting...God bless new to your channel.... pashout out katech...
Thanks very much I have learn so much from your video God bless you sir
You are very welcome
Superb job sir🙏
Good job....thanks 👍
Good job great job
Good job like always ⭐⭐⭐⭐⭐
Thanks again!
I like your video!!!!
Very good job
Thank you! Cheers!
Great video thanks very much for all you show here in your chanel , is very much apreciated.
My pleasure
Saya suka cara kerjanya ...cepat dan akurat...
❤
sir exelint information good works
Keep watching
Excelente 👌
Show amigo Bela dica
Good work boss
Nice video 🙏🙏
Many many thanks
Keep up the outstanding work tevz 📺👏👏👏👏
Hai watchung ur channel from india
Excellent super bro thanks
Welcome
Thanks you very much really l like your nice video.
You are most welcome
Nice video
Thanks
thanks you so much sir another tip to isolate the shorted line
well don sir
Sir, My congratulations 👍🙏.
Many many thanks
Expert na sa trabaho
Saludos, excelente video
Your voice is excellent .
AI voice. He probably doesn't speak good Engiish. Very helpful. He is very smart technician, doesn't have to speak English.
Thanks for sharing sir.
What is the reason why you chose to use your analog voltmeter when checking voltages?
I also use digital, I use analog on this video because its easier to see if the voltages fluctuate. See the needle moving up and down.
@@tevzTVTevatronics thanks for explaining sir. I learned something new again.
Simply magic
nice job
Thanks!
great master
good job repairing that kind of trouble shoot
thanks
Thank you friend.
Thank you too
Good job thank you
Thank you to
Hello, i just want to ask
How we get the same value capasitor that you have changed?
Is possible if we install a random value one?
Отличная работа! Спасибо за интересное видео.
P.S. За кадром петушки кукарекают 😊👍 Круто!
Good boy
Thanks sir please give one video for best tresing method for finding short component in any motherboard for 1.8,3.3,and 5 volt shortnig
Thanks for exposing
No problem
Good evening, very good video, I saw that you changed the capacitor, how did you know its capacity, so that we can learn too.
When it comes to shorting you first check the capacitors, they are prone to shorting
Hi it's mostly guess work and experience i guess for the capacitor value. You can measure those in the other rails i guess and try. Or sometimes you lucky and find the circuit diagram. Yep unfortunately lots of guess 😂
I think he just left out the capacitor. The capacitor is there to reduce any noise on the power from affecting the signal. Any capacitor value of the same order of magnitude should suffice if you find you need the filtering.
👍👍
👍
Hi sir, when checking shorted capacitor, tv must be plugged in or should be off ?
And multimeter should be on DC mode or continuecy mode please
It must be unplugged. resistance continuity mode with a buzzer.
was that a T-Con board ?
good
Sir very informative video, I have vertical line's for first 4 minutes and slowly freezing picture with audio starts then in another minute clear picture with proper audio comes from LG-47LA6200 TV (3D model). I kindly advise, all voltages are okay from T-Con board.
Reflow the MCU the big IC
@@tevzTVTevatronics Thanks Sir, will check and reply back
Hii tevs. I'm a big fan of your videos. Please make a video on how to modify led TV power factor correction. All led TVs from 42 inches
Will try
Hi, at 5:25, not really sure of their name, but there are golden tapes with traces soldered at the top of the board, one of them on my tv got detached, is it possible to solder it again on the board?
Yes it can be solder back.
Thank you sir
I have a Panasonic 50 inch. TC-P50G25 plasma 2010 model and 4 blinks any suggestions to fix! Thanks
Thank you
with what value you replaced that capacitor please ?
Great job btw
2.2 microfarad upto 47 microfarad will work.
@@tevzTVTevatronics thx a lot man
Hello, how are you? I brought an LG 37lg606 ur LCD TV for repair. The inverter board had a problem and the TV only stays on standby. A fuse and MOSFET number 8447 were burned on the inverter board. I replaced it and replaced the MOSFET with 45n03. Now the TV turns on. The image fills the problem. Is there a replacement for MOSFET or not? Thank you for your guidance. 🙏🙏🙏🙏
I'm good thanks. Is the backlight turned on now?
@@tevzTVTevatronics Yes, the picture is perfect, when I use MOSFET 45n03, the picture fills up and today I used another MOSFET 50n06 and the picture came, but the picture gets dark in the middle, it doesn't fill up anymore.
@@tevzTVTevatronics If possible, give me your Instagram ID or WhatsApp number so that I can send you the video
what is value of C57 capacitor was replaced? Farad? Voltage? Thanks
thanks
Welcome
Greet
Good Good
Thanks
grazie
Thanks
Welcome
Hi Tevz, how to know the value of the faulty capacitor, unless you have its circuit diagram?
The neighbor capacitors usualy have similar values
@@tevzTVTevatronics Thanks.
❤️💕❤️👍💕❤️❤️💕❤️🧚
Hello, considering the connection of many parts, how did you determine that this capacitor has a connection?
And why didn't you assemble that capacitor
Thus capacitors are connected in parallel so they like all are shorted. do you mean to desolder the capacitor? I desolder the lowest ohm reading and that the suspected shorted capacitor.
@@tevzTVTevatronics Thank you for your response
So, we take the ohmic capacitors in places where the ohms are much lower than in other places, if we have them, is the part suspected to be connected
@@tevzTVTevatronics What I mean is that after diagnosing the defective capacitor, you did not assemble the new capacitor in its plac
@@protection4541 its was ua-cam.com/video/Cvvv42mGp2M/v-deo.html
Another Philip model K320wd8 same to your troubleshooting issue standby mode and no video.
I have monitor TV P2250 turn on for 1 second and off again
What you thing is the problem in your experience?
its the backlight or the panel that may have the problem.
😄😄😄😄😄😄
Sar how to capacitor value calculate please video
Brother you from which country ?
Philipines
Thanks
San mo nakuha announcer mo🤣🤣😂 lufet
windows narator
Nice. tanong lng po. Meron po kami na LG 55in tv, kaya pa po ba marepair ang lcd panel na may open/shorted circuit? bali ni-repair po ng technician at ginawa ay ung tape method.. pero kaya pa po ba tlga magawa ung pinaka sira nun na circuit?
seguimos aprendiendo.
pls sir..this panal VAA prasent Q1 smd transister nomber...? ...or data..? thanks...
Your videos good but music is very distabance
so that problem part wasnt even needed in long run?
What is the value of the capacitor
Sony 55x7007E after 30minutes On and Off amd the other one with the same model no video , the backlight will tun On and then Off after blinking 6x
i change the ac convertor 5 capacittors and the line draiver , the scren function vhen the logo samsung start then the scren bluring.
New subs her sir
Thanks for subbing
My samsung 32" led tv backlight turns on and off when the power supply or card is touching the metal of the led. But when i lift both boards then the backlight turns on. And there are colored vertical lines on whole screen.
The panel have hair lines.
Newbie is watching
Why you use analog multimeter
7:58 was that a beer crack sound at 8:00 min
Sir tel me your country name
Philippines
W
Practically impossible to have 0.5 Ohm as tracing line resistance !!
Pano po mlaman ang same value ng smd caps na ipapalit sir
Pwede 2,2 uf to 47 uf.
i am electronics tic in ksa
Good boy translate to Sinhala
Madali tingnan piro kami na gumawa. Napaka hirap talaga