I was quite impressed by this product. I put it on my Ubuntu Linux box, and in about 5 minutes.. ( Using v 0.19 ) I had my first Laser Engraving done! Excellent work. My K40 was cheap.. but your software made it easy to work with. I had been using your F-Engrave product for what seems like decades .. didn't correlate the two till I went to your main page. Excellent job.. anything that keeps me off Windows is making my life easier. Thanks again.
I had 2 computers say they could not find inkscape. It worked fine on its own but it was not located where you would think in program files. I had used this for years but always installed from the Windows store. I uninstalled that and then installed the windows program version and all is good. Putting it out there if someone else has the problem. Just getting started and having fun. I thought I would be upgrading my board but I will use this for now since it works well. Thanks.
Thanks for great work! Whisperer is only software I use with my K40 since early versions. I've added my own gcodes before, but now it is implemented. Great improvements with every new version!
This software works great and I have found it works great with Rhinoceros CAD when you configure the layer color match k40w setting. One thing would be helpful if you could change pen on the GUI. Found a few times I had forgot to change color on a given vector. Other would be able to delete vector if something export ported that you didn't want.. Keep up the great work...
Newby to your site had to change from Corel Laser to Whisperer like this system better. I still use CorelDraw. This was very easy to watch and learn. Thanks
Hi, I have a problem that I can't solve, I recently bought a laser machine with Controler M2 nano, well I connected my Rotary but I can't get it to work properly, I use the K40 whisperer as a program to start the laser machine. I have tried several times but the Rotary doesn't work well. Can you kindly help me what kind of setting I need to do to make the rotary work well? Thanks, I'm in Italy.
hello there, I installed this and inkscape in my computer , but it shows an error that reads" inkscape not found" I typed in the file address in general settings still does not work, can you help?
If you have not already installed Inkscape, it needs to br installed for K40 Whisperer to open SVH files. Full install instructions are here: www.scorchworks.com/K40whisperer/k40w_setup.html
I have a problem with the rotary settings. I have allowed the rotary use but when I turn the laser on it either doesn't find it (USB error) or it keeps spinning and doesn't stop (as if it's looking for the home point). So far I have not found any solution to this.
Can I generate gcode with Vectric Aspire and load it directly into k40 whisperer? What would I need to do for that? I run a cnc machine on the same computer using mach3 and design in Aspire.
Excellent video. I have a problem with my K40 that I haven't being able to solve. No matter what I do, the cutting starts at the middle of the cutting area. Can this information that you show here solve my problem?
I am not sure why you care what it cuts first. Are you trying to save the 1/2 second it taked to move the head to the 1st cut? Or is the whole dedign not where you want it?
Thanks for your reply. Apparently, I was not clear enough. My apologies for this. What I meant is that the machine should start cutting on the left top section of the balsa sheet I am trying to cut. The problem is that it starts to cut at the center of the sheet and if it continues to cut, it will continue to cut outside the sheet, as if the drawing was not properly located on Inkscape and K40 Whisperer. It is not a matter of saving 1/2 second. It is as you say, that the whole design is theoretically outside the sheet I am trying to cut. I hope I make myself clear, If not, I would like to send you a screen print of the problem. Thanks for your kindness. EDUARDO
freebird1963 Yes, the changes are listed right above the download links on the K40 Whispered web page. The list is labeled "Changes in Version 0.17" www.scorchworks.com/K40whisperer/k40whisperer.html#changes
I have this same problem and cannot figure out how to correct it. I am trying to cut a design out of a piece of acrylic and because it has many sharp edges I am doing several passes to make the cut but it keeps changing the starting position even if I push the "home" it still goes to a different spot.
I just bought a new 60w high precise Chinese laser engraver on Ebay. It came with laserDraw/corel laser and corelDraw_x4. I was unable to install the corel Draw software as it was not compatible with windows 10. I was referred by the Ebay seller to your software as easy to use especially for a first time user. I had a few questions before installing your software. Cant find an email address to contact you.
love this it works great with my k40 - i have a question about DXF files as i design in auto cad - when i try to open it tells me it can't - the file has 7 layers - is this why it can't open it?
No, the layers should not prevent opening it. K40 Whisperer cannot open binary DXF files so make sure you are not writting binary DXF files from autocad
@@claytonstoltz1992 K40 Whisperer does not support DXF text or raster engraving from DXF files. A lot of programs havevthe option to export text as lines.
I am designing on Mac and I transfer to windows laptop to connect to my 40k laser but I put the size and machine engraving smaller size , how can I do same size I could not find it on whisperer :(
WOW. This is like having a new machine! One question. With Coral I was making plaques that used 2 raster images on two layers. I would engrave one layer on low power for a background, then engrave the second on higher power to be the main image. With K40 Whisperer I could probably do this using two files. Is there an easier way?
Fortunately for us, this guy made a Mac installer for k40 whisperer that you can download the disk image here: github.com/stephenhouser/k40-whisperer/releases/download/v0.31/K40-Whisperer-0.31.dmg
Follow along with this video it is a better introduction. ua-cam.com/video/9wYvbenigtk/v-deo.html If you still have problems you need to provide more details. (Explain what you did and provide error messages or describe the programs response to your inputs. Saying it doesn't allow you to cut is too vague to be useful to anyone.)
Try moving the laser head a little to the right before you start your job. Your head might be hitting the hardstop one the left and missing steps in the middle of your design.
Something is causing the computer to loose connection with the laser. Some people say replacing the USB cable helps. I may be electrical noise in you setup somewhere.
I was quite impressed by this product. I put it on my Ubuntu Linux box, and in about 5 minutes.. ( Using v 0.19 ) I had my first Laser Engraving done! Excellent work. My K40 was cheap.. but your software made it easy to work with. I had been using your F-Engrave product for what seems like decades .. didn't correlate the two till I went to your main page. Excellent job.. anything that keeps me off Windows is making my life easier. Thanks again.
I had 2 computers say they could not find inkscape. It worked fine on its own but it was not located where you would think in program files. I had used this for years but always installed from the Windows store. I uninstalled that and then installed the windows program version and all is good. Putting it out there if someone else has the problem. Just getting started and having fun. I thought I would be upgrading my board but I will use this for now since it works well. Thanks.
Thanks for great work! Whisperer is only software I use with my K40 since early versions. I've added my own gcodes before, but now it is implemented. Great improvements with every new version!
This software works great and I have found it works great with Rhinoceros CAD when you configure the layer color match k40w setting. One thing would be helpful if you could change pen on the GUI. Found a few times I had forgot to change color on a given vector. Other would be able to delete vector if something export ported that you didn't want.. Keep up the great work...
Newby to your site had to change from Corel Laser to Whisperer like this system better. I still use CorelDraw. This was very easy to watch and learn. Thanks
I'm as thick as the vicar's knickers but even I found this easy! Superb program. Thank you very, very much.
Hi, I have a problem that I can't solve, I recently bought a laser machine with Controler M2 nano, well I connected my Rotary but I can't get it to work properly, I use the K40 whisperer as a program to start the laser machine. I have tried several times but the Rotary doesn't work well. Can you kindly help me what kind of setting I need to do to make the rotary work well? Thanks, I'm in Italy.
Very nice!
hello there, I installed this and inkscape in my computer , but it shows an error that reads" inkscape not found" I typed in the file address in general settings still does not work, can you help?
You may have pointed K40 Whisperer to a "link" not the executable.
I can’t get my images to load from Inkscape to k40 whisper. Says it can’t find Inkscape. Then it said needs elevation. I can’t figure it out
If you have not already installed Inkscape, it needs to br installed for K40 Whisperer to open SVH files. Full install instructions are here: www.scorchworks.com/K40whisperer/k40w_setup.html
I have a problem with the rotary settings. I have allowed the rotary use but when I turn the laser on it either doesn't find it (USB error) or it keeps spinning and doesn't stop (as if it's looking for the home point). So far I have not found any solution to this.
Pushing the gantry up to the y end stop switch will stop it from spinning.
Hello SR, this means that i can move the k40 into a bigger xy stage and still use whisperer due to the corrdinate system slection?
Pedro Fernandez yes, you can set the laser area to somthing bigger.
Thanks i have a second machine and a 400x600 xy stage so ill stick on with the stock electronics for now with the Whisperer
ua-cam.com/video/oCYQqHhTlQ0/v-deo.html the project is alive the franken 40 running with k40 whisperer
Freaking awesome.
Can I generate gcode with Vectric Aspire and load it directly into k40 whisperer? What would I need to do for that? I run a cnc machine on the same computer using mach3 and design in Aspire.
+berighteous Yes, that is the topic of the next video.
Scorch Works You are the man! Great work! Can't tell you how much I appreciate everything you do. Looking forward to your next video
Excellent video. I have a problem with my K40 that I haven't being able to solve. No matter what I do, the cutting starts at the middle of the cutting area. Can this information that you show here solve my problem?
I am not sure why you care what it cuts first. Are you trying to save the 1/2 second it taked to move the head to the 1st cut? Or is the whole dedign not where you want it?
Thanks for your reply. Apparently, I was not clear enough. My apologies for this. What I meant is that the machine should start cutting on the left top section of the balsa sheet I am trying to cut. The problem is that it starts to cut at the center of the sheet and if it continues to cut, it will continue to cut outside the sheet, as if the drawing was not properly located on Inkscape and K40 Whisperer. It is not a matter of saving 1/2 second. It is as you say, that the whole design is theoretically outside the sheet I am trying to cut. I hope I make myself clear, If not, I would like to send you a screen print of the problem. Thanks for your kindness. EDUARDO
Make sure you resize the page to the design size as shown in the video.
Do you have thw origun dxs file? In min (1:42)
No, I do not
Does whisperer utilize inkscape dlls for image processing? Just womdering it needs the path....
+Printin Addiction it uses Inkscape to create the raster engraving image. It runs the Inkscape exacutable like you can from a command line.
Is there a file or place that shows the new features in each release. Saw .17 was released but didn't find a whats new listing. Thanks
freebird1963 Yes, the changes are listed right above the download links on the K40 Whispered web page. The list is labeled "Changes in Version 0.17" www.scorchworks.com/K40whisperer/k40whisperer.html#changes
second pass on vector cutting always looses position resulting in an displaced cut even when I tried resseting to the home position. Any suggestion
Does it improve if you reduce the speed? Your stepper motors may be missing steps.
I have this same problem and cannot figure out how to correct it. I am trying to cut a design out of a piece of acrylic and because it has many sharp edges I am doing several passes to make the cut but it keeps changing the starting position even if I push the "home" it still goes to a different spot.
I just bought a new 60w high precise Chinese laser engraver on Ebay. It came with laserDraw/corel laser and corelDraw_x4. I was unable to install the corel Draw software as it was not compatible with windows 10. I was referred by the Ebay seller to your software as easy to use especially for a first time user. I had a few questions before installing your software. Cant find an email address to contact you.
There is an e-mail address at the bottom of the web page (in the logo image)
love this it works great with my k40 - i have a question about DXF files as i design in auto cad - when i try to open it tells me it can't - the file has 7 layers - is this why it can't open it?
No, the layers should not prevent opening it. K40 Whisperer cannot open binary DXF files so make sure you are not writting binary DXF files from autocad
@@ScorchWorks it imports now but ignores text :( what am i missing?
@@claytonstoltz1992 K40 Whisperer does not support DXF text or raster engraving from DXF files. A lot of programs havevthe option to export text as lines.
thank you.
Hi when using a dxf file in whisperer, how do you tell the program to first cut the inside pieces ?
+Hennie Vos it always tries to cut the inside parts first.
Good job, can you install a funtion in the next version of K40 Whisperer in wich you can engrave from bottom to top? Thank You!!
bad wolf it already hs that option.
I am designing on Mac and I transfer to windows laptop to connect to my 40k laser but I put the size and machine engraving smaller size , how can I do same size I could not find it on whisperer :(
Open it in Inkscape and change the size.
WOW. This is like having a new machine!
One question. With Coral I was making plaques that used 2 raster images on two layers. I would engrave one layer on low power for a background, then engrave the second on higher power to be the main image. With K40 Whisperer I could probably do this using two files. Is there an easier way?
+Larry Nielsen Unfortunatly two files is probably the easiest way to do that with K40 Whisperer. More advanced features may come in the future.
No worries. It is great as is. This year I was able to make the Christmas ornament that I continually failed at last year.
I need help installing k40 whisperer on mac. Do you have a tutorial on how to download and install?
Fortunately for us, this guy made a Mac installer for k40 whisperer that you can download the disk image here:
github.com/stephenhouser/k40-whisperer/releases/download/v0.31/K40-Whisperer-0.31.dmg
Is it possible to start engraving referring to the center of an image, instead to the top-left?
I found it. Beautiful program!
@@MDinsideZ im trying to figure this out, can you point me in the right direction?
i downlaoded k4 whisper but its not allowing me to cut ?
Follow along with this video it is a better introduction.
ua-cam.com/video/9wYvbenigtk/v-deo.html
If you still have problems you need to provide more details. (Explain what you did and provide error messages or describe the programs response to your inputs. Saying it doesn't allow you to cut is too vague to be useful to anyone.)
Hi can anyone help me, I do an engraving then when I go to cut it out it is of by 1cm or so to the right???
Try moving the laser head a little to the right before you start your job. Your head might be hitting the hardstop one the left and missing steps in the middle of your design.
@@ScorchWorks it was working fine yesterday, just today it started
@@ScorchWorks even if I do it in the middle every time I press cut it will cut 1cm to the right
Is is specific to a design?
@@ScorchWorks yes I have tryed other designs same thing happens
i keep getting USB time out, what is causing this and how can i correct it
Something is causing the computer to loose connection with the laser. Some people say replacing the USB cable helps. I may be electrical noise in you setup somewhere.
link does not working
Eagle Eye I fixed it.