Good day Sir! Very interesting combination on this version of the amplifier, I mean that here the amplifier power GND + speaker output and signal input converge in one connection. And one week latter I bought a preamplifier board (for power supply it needs GND and + 12 volts), and since my power supply is -28 GND + 28 volts, I made a voltage regulator on a field-effect transistor and a variable resistor. So when connecting it, a background hum is heard from the speakers, I think that this is due to the fact that the power GND is connected to the signal GND and also feeds the preamplifier. Apparently, in combination with this circuitry, the preamplifier cannot be connected. and it is probably impossible to separate the power GND from the signal GND. Tomorrow I will try it on the first amplifier that I also assembled according to your video, where the main transistors use 2SC 5200 and it has a unipolar power supply. The most interesting thing is that the first amplifier, when the sound is almost at maximum, drops the supply voltage from 26.7 volts to almost 23 - 20 volts. Most likely, tomorrow I will make a video with them, or in a few days, and send a link.
I don’t know yet for what reason, but the amplifier is quiet (about four times quieter than yours), what could be the reason? I assume that maybe because of the resistance of 3.3 K ohms, I think to replace it with 1 K ohm.
Hello! Is it possible to find out from the power supply if I have +28 0 -28 volts for transistors 2 sc5200 and 2sa1943, this is not critical, is it? And another question about the diodes on the power supply, I put three amperes, aren't they too weak for this power?
Hello, dear master! On the audio amplifier assembled according to your scheme (where 2sc5200 and 2sc1943 are used), only 2sk1943 heats up (within the operating temperature), and 2sk5200 does not heat up. Is this normal? I also tried replacing the BC558 transistors with MP25A germanium transistors made in the USSR year of manufacture is 1984, and the bass became softer. On the next amplifier assembly (the same model), I will only install GT 402 and GT404 germanium transistors (instead of BD139 and BD140), also made in the USSR, their year of manufacture is 1976. Of course, their gain is small, I think the bass will sound even more gentle. I"m hope i not mistaken in this.
Hi! Haven't I bothered you with my comments yet? I tried to disassemble the amplifier and assemble it again. I checked each unit, both transistors and resistors, so far 2sk 5200 is cold, only 2sa 1943 is warm. I'm just wondering what the problem is. Well, my power supply is 26-27 volts, it's unlikely that this would happen because of two volts. Tomorrow I'll shoot a video, upload it to my channel, and show it. And the transistors are on separate radiators.
Even for the sake of interest, instead of 2 sk 5200 I installed mjw 21196, also NPN, although it is not a complementary pair for sa 1943 and there is practically no difference in sound and it is cold.
Hello sir. I have here some issue. I have no available dual transformer for this amp. Can i use single dc power input? Is it ok if i connect the negative line and the ground together? Thank you sir. I am looking forward of your response. God bless. From Philippines
@@RJEDITALL i have made it,,with 25volts ct 5amper,,no matter how many watts it is,,but it's enough for 10 inch subwoofer,,but it gets very hot after 5 minutes of turning on,, why,,?
Today I finished the amplifier according to this scheme, but have not yet tested it. Instead of 2sc5200 + 2sc1943, I have MJL21196 + MJL21195, And also, instead of bd 140 + bd139, there are mje 340 + mje 350 transistors. Do you think that with this configuration, will the power be good or not?
Oi bridge mud a theke 2 tansistar output onek besi. 4 pis tansistar a aro com output ho6e .appnar sab project baniye baniye dekhe6i ai 2 transistor ar awozz onek besi. . 2 to Kore tansistar ar sem setting bridge mud kemon vabe korbo please reply din sir
buenos dias amigo, necesito de se valiosa ayuda, he visto varios videos suyos con respecto a estos dos transistores en particular 2sc5200 y dsa1943 ,porque tengo una bocina de 15 pulgadas que traia estos dos componentes y una alimentacion de 45+ 0 45- y cerca de los 2 transistores de potencia traia 5 transistores h649a x3 y h669a x2 y te pregunto si ¿este circuito aguantaría el voltaje que tengo ?para ya no modificar nada.
@@RJEDITALL gracias por responder pero como no se calcular tendre que aventurarme a poner bd140 en vez de los bc558 a ver si lo logro.saludos desde veracruz ,Mexico
Sir 2 pis tansistar. Are ekta 2pis tansistar seem baniye6i. Duto carcit K Bridge mud ki vabe at korbo sir please help Korun replay AR apekhay a6i sir please
Lajwab...
Transistor wala same bnayn sath 2 speaker chl sky , or 2 left right volume lgayn zror, boht neat and clean diagram 👍🇲🇷⚘
@@HussainKhan-yy7fm ok
Nice choice of transistors. Quality components Bc558 is a nice transistor. They make nice first stage drive op amps ✌️🤓💯
Wow wonderful share worth watching 😀👌👌
Good day Sir! Very interesting combination on this version of the amplifier, I mean that here the amplifier power GND + speaker output and signal input converge in one connection. And one week latter I bought a preamplifier board (for power supply it needs GND and + 12 volts), and since my power supply is -28 GND + 28 volts, I made a voltage regulator on a field-effect transistor and a variable resistor. So when connecting it, a background hum is heard from the speakers, I think that this is due to the fact that the power GND is connected to the signal GND and also feeds the preamplifier. Apparently, in combination with this circuitry, the preamplifier cannot be connected. and it is probably impossible to separate the power GND from the signal GND. Tomorrow I will try it on the first amplifier that I also assembled according to your video, where the main transistors use 2SC 5200 and it has a unipolar power supply. The most interesting thing is that the first amplifier, when the sound is almost at maximum, drops the supply voltage from 26.7 volts to almost 23 - 20 volts. Most likely, tomorrow I will make a video with them, or in a few days, and send a link.
Real 100 watt autput sir your best electronic good information sir thenkyou so much. [ ❤ ]
U are most welcome
Wow best stereo amplifier circuit make you brother 👍
Thanks, mono amplifier
Excellent amplifier, i like, salute from Venezuela..!
Thanks bro
Nice sound, but i like a strong driver.very nice your project good job.
Thank you so much
Muito boa montagem, gosto assim bem explicado, parabéns, ótimo trabalho
❤️❤️
Sir congratulations to you sir.for this video uploaded
Thank you so much
Nice Best circuit board thanks
Thank you so much
Pretty nice drive stage ✌️🤓🤗
You win porfect ✌ ...👌👍
Thanks
@@RJEDITALL sir ..power supply kitna .tak..jhel lega..
it's really works I made is thaks to u
Thnx for comment
Is the idea successful? Did he work with a good image and a strong voice?
Clear sounds brother.good job
Thnx
Nice good job👍
Thanks for visit
Can i replace the transformer by placing two 20v laptop bricks in series and using the connection middle pin as the 0v?
Yes
Good job done
Show de bola mano amplificadores
Muy bueno el amplificador 👌👌👌
Thank you so much 👍
The circuit 😊
Nice video.
Sir please send circuit diagram
Nice circuit ... but dont let the bare wires hanging like that ... make sure they dont touch or it will short circuit
Nice video
Thanks
Very good
Thank you so much 👍
Plz make a video on how to install mp3 player on various circuits,,like amplifier,woofer,radios e.t.c.
Brother gain thoda kam lag raha hai Keya kare? Power supply - 45-0-45 v 6 amp dc pura 100 watt nahi milraha same to same banaya hai 2 pc
Acha se check karke dekho, transistor check karo
Te agradezco muy bien explicado.lo voy a ser este me gusto mas que todo este modulo no tiene distorsión
Que tanto se calienta ? Necesita ventilación?
I don’t know yet for what reason, but the amplifier is quiet (about four times quieter than yours), what could be the reason? I assume that maybe because of the resistance of 3.3 K ohms, I think to replace it with 1 K ohm.
If you know, try
@@RJEDITALL Thanks so much!
Hi❤
👍
Circuit is working but 22 ohms 5 watts resistors over heat and slowly noise is there I am using 24 0 24 5amp transformer
0.22 omh not 22 omh.i think so
মই এইটো ইউজিন কিনিব বিছাৰো এইটোৰ দাম কিমান
Thanku is good circuit
Hello! Is it possible to find out from the power supply if I have +28 0 -28 volts for transistors 2 sc5200 and 2sa1943, this is not critical, is it? And another question about the diodes on the power supply, I put three amperes, aren't they too weak for this power?
You try
gonna try this one out soon
Did you do this? Did they work in a good voice?
Nice
❤️
I made it and it worked very well but after few minutes the bd139 two transistors were got damaged 😢 and not working now. Please help 😢😢
You use heatsink on bd139
@@RJEDITALL yes I used small heat sinks for all transistors.But still got damaged .So,what can I do now?
Vlw gostei muito parabéns
Thanks
Hello, dear master! On the audio amplifier assembled according to your scheme (where 2sc5200 and 2sc1943 are used), only 2sk1943 heats up (within the operating temperature), and 2sk5200 does not heat up. Is this normal? I also tried replacing the BC558 transistors with MP25A germanium transistors made in the USSR year of manufacture is 1984, and the bass became softer. On the next amplifier assembly (the same model), I will only install GT 402 and GT404 germanium transistors (instead of BD139 and BD140), also made in the USSR, their year of manufacture is 1976. Of course, their gain is small, I think the bass will sound even more gentle. I"m hope i not mistaken in this.
@@dregozver3726 no heating problem, check your transistor b c e with multimeter. And connect
Hi! Haven't I bothered you with my comments yet? I tried to disassemble the amplifier and assemble it again. I checked each unit, both transistors and resistors, so far 2sk 5200 is cold, only 2sa 1943 is warm. I'm just wondering what the problem is. Well, my power supply is 26-27 volts, it's unlikely that this would happen because of two volts. Tomorrow I'll shoot a video, upload it to my channel, and show it. And the transistors are on separate radiators.
Even for the sake of interest, instead of 2 sk 5200 I installed mjw 21196, also NPN, although it is not a complementary pair for sa 1943 and there is practically no difference in sound and it is cold.
Muito bom
And the film capacitor 104J and 104K are they the same in capacity? I only have 104K.
Yes, same
@@RJEDITALL Thanks so much!
Please post circuit in discrption below
Hello sir. I have here some issue. I have no available dual transformer for this amp. Can i use single dc power input? Is it ok if i connect the negative line and the ground together? Thank you sir. I am looking forward of your response. God bless. From Philippines
No bro, This circuit working double dc power supply, + , - , gnd
Thank you sir.
Thank you sir
Npn transistor d882 and PNP transistor 772 kia ye dono transistor bd 139 and 140 ki jagha use kar sakta hun bd139 140 nahi mil rahy....
Yes they will be even better because they have higher current ratings and are excillent for driving big transistors
Yes
muito Bom
Thank you for comment
You great master!!! I week latter start making amplifier from your schema. With sc5200. Sc5200=TTC 5200? Or not?
2sc5200 or ttc5200 same. Thanks for visit
I'm having trouble with the 152 capacitor, can I replace it with another value, if so what is the value
You can use 102
@@RJEDITALL ok thank you,,
@@RJEDITALL i have made it,,with 25volts ct 5amper,,no matter how many watts it is,,but it's enough for 10 inch subwoofer,,but it gets very hot after 5 minutes of turning on,,
why,,?
Um transformador de 2 amperes puxa esse mini amplificador?
Today I finished the amplifier according to this scheme, but have not yet tested it. Instead of 2sc5200 + 2sc1943, I have MJL21196 + MJL21195, And also, instead of bd 140 + bd139, there are mje 340 + mje 350 transistors. Do you think that with this configuration, will the power be good or not?
Check your transistor npn and PNP
Aisa bass trouble board banao jo sabhi amplifier mai chal sake plz
Ok
Resistors watt kya ha ohm or k ki pleas sir
Out put kitne ha circuit ki
In full course for powerfull bass amplifier how to put bass ,vol & trebble of the amplifier
Please watch another video in my channel, bass treble and volume controller
Amigo. Buen circuito, gracias. Puedes enviarme el diagrama?
Take a look at the diagram given inside the video
what if the final transistor is replaced with a sanken transistor? does the circuit work?
Yes working, you can use any PNP transistor instead 558
hello friend how many wats does this amplifier provide?
100 watt
Kya bc558 ke jagah c100 ya koi v pnp transistor use kr sakte hai ,
Yes, you can use any PNP transistor ( small Size)
Can we use 12inch sub 1200watts in this
Maximum 200 Watt
I want nf 158 pf how can i get
Yes, you can try
Sele pueden agregar otros dos saludos desde Colombia
Nf 152 capacitor equivalent plssss
amplifier output wattage ??
150-250 watt
Late comment sir. I have question sir. Can i replace 1uf 63v with 1uf 50v? Wait your reply. Thanks. Philippines.
Yes, 100% . Thanks for visit
I don't have nf152 what can I use
102j you can use
its powerfull,,canyou give me cercuit diagram.?or PDF
Hi my friend you are so good but sorry can you give me the diagram of 1000 WATTS of amprifire
Sorry
Este mismo aplificador pero con los conectores de audio, de salida de audio y entrada de corriente
sir which transistor I can use to replace 772
Excelentes todos tus proyectos!!!! felicitaciones por tu canal..
Thank you so much for the visit
Can i use only 3055 tansistor
Use 2n3055 and mje2955 package
How we can put volume controller in that circuit
Where audio cable is connected. You can put a volume controller there
Eu queria saber esse módulo funciona com bateria de carro
No, It's only working by transformer , 24-00-24. 👍👍
Oi bridge mud a theke 2 tansistar output onek besi. 4 pis tansistar a aro com output ho6e .appnar sab project baniye baniye dekhe6i ai 2 transistor ar awozz onek besi. . 2 to Kore tansistar ar sem setting bridge mud kemon vabe korbo please reply din sir
I will try
Hola amigo, es clase A o Clase Ab? Cuantos wtts da este amplificador grc muy bueno! 👍
Class ab, 100-200 watt
@@RJEDITALL muchas grc amigo por contestar saludos desd argentina!! 👍
2ps 8 inch speaker is mei chalega kya
8 Ohms 2 speaker parallel connection Karke chalega 👍
Sir , can I use tip41c and tip42c?
Yes, you can try
Nf152 replacement plsss reply
152 above 473
35 0 35 supply use kr sakte hai
Yes
Heat issue to nahi hoga or same additional transistor use kr ke stereo bna sakte hai
Lo e armando y si funciona como el video muy bueno y barato de fabricar . Lo hice el diseño PCB para un ensamblaje mas sencillo
Please full video watchThe diagram is given inside the video
Encerio que tal te quedo
@@tonycarranza1682 super ok .
Suena super . Pero la potencia es limitada .
@@mecatest9440 como así que la potencia es limitada???
@@mecatest9440 será que me funciona para 6 bocinas y 4 Subwofer de equipo de casa esque las tengo allí sin uso
buenos dias amigo, necesito de se valiosa ayuda, he visto varios videos suyos con respecto a estos dos transistores en particular 2sc5200 y dsa1943 ,porque tengo una bocina de 15 pulgadas que traia estos dos componentes y una alimentacion de 45+ 0 45- y cerca de los 2 transistores de potencia traia 5 transistores h649a x3 y h669a x2 y te pregunto si ¿este circuito aguantaría el voltaje que tengo ?para ya no modificar nada.
You can use any NPN and PNP transistor. You add minimum 5 NPN and 5 PNP transistor for your this volt
@@RJEDITALL gracias por responder pero como no se calcular tendre que aventurarme a poner bd140 en vez de los bc558 a ver si lo logro.saludos desde veracruz ,Mexico
@@MrKNECIO You can use bd140 instead 558
Sir ya circuit board 24 0 24 transfamar 5ampar ma Chala ga kaya
Chalega, no problems
Kitnaa volt takk dena miltaa hy yess parr 🤔🤔🤔
Orrr kitna watt kaa hy wy
Maximum 30-0-30v 10 ampere
Muito bom !!!
Thanks
quantos wats rms tem esse amplificador?
100w
can i use tip2955 and tip3055 sir,,
Yes
@@RJEDITALL ok thank u sir,,
Escuseme sr, i don't have capacitor 152 nf, which one ,i'll can to use
You can use above 200 nf
Tanks so much sr God blass yuo
De cuantos wtts es
5200 139 140 2pis 558 mila kar amplifier 1943 nahi ho pahale wala 5200 1943 ka amplifier banaye aachha chal raha hai
Sir 2 pis tansistar. Are ekta 2pis tansistar seem baniye6i. Duto carcit K Bridge mud ki vabe at korbo sir please help Korun replay AR apekhay a6i sir please
Please check in my Channel, bridge mood amplifier
HI..2 PNP 2NPN
AMPLIFIER YAP toplam 8 transistor stero amlifier 1 kanal 4 transistor 1 kanal 4 süper
You can use
Dada diagram dile vlo hoto ikto
Please check diagram in the video
Is me 4558 ic add kar ke video banano vai only bass k liya plz
Wait karo Bhai. Lockdown chal Raha hain.
Han ji thik h and advance thanks to u bagwan se dua karta hu ap ta UA-cam channel or vi tarakki kare no.1 ho jai.... God bless u
2sc5200 ka bina pcb ka amplifier
Can I use 5198 and 1941
Yes, 100%
Curcit ready h par 18 0 18 ta power supply h to usse kam chalega kay ?
Sir all resistance kiy watt ha
Quatr watt all and 5 watt 2 pcs
@@RJEDITALL kon se ha 5 watt ke sir white wale
Yes , white wala
Thank you
Sir
Nf 152 ki jaga aur konsalaga sakte hai
NF 300 ke opar jo milega laga sakte hain
Can I use 5193 1941 ?
You can use any NPN and PNP transistor
salcon bass treable circuit diagram Please Bangladesh
Please check in my Channel
My frends, I can to use, capacitor 1 uf 50 volts, dont have the capacitor 1uf 63 volts thanks, I hope do yuo cn help me
Please English language
yes its ok
Sir 1943 transistor ma jo 5watt ka resistor Hana o bohoti hit horahaha please solve this problem
ache se check karlo, hit nahi hoga,
Sir Ai 25 0 25 ar 4 tansistar ar video banana sir
Ok