DIY High Power Amplifier Very Simple Using 20 Transistors 2SC5200 & 2SA1943 with TL072 IC
Вставка
- Опубліковано 30 лип 2024
- 0:00 Introduction
0:55 Install the amplifier circuit
13:03 Install the power supply and connect
17:09 Start testing
How to build high power amplifier VERY SIMPLE, using 20 transistors 2SC5200 & 2SA1943 with TL072 IC audio preamplifier applications.
Low Noise, Low Power Consumption
Low Total Harmonic Distortion
High Input Impedance . . . JFET Input Stage
Internal Frequency Compensation
The amplifier circuit delivers powerful bass and super clear sounds
DIY High power amplifier very simple, using 20 transistors 2SC5200 & 2SA1943 with TL072 IC
➤ Copyright © by Share Tech Creative
➤ Follow me: / sharetechcreative…
➤ Follow Facebook: bit.ly/3eEHjNb
➤ 📺 Thanks for watching!
➤ Parts Required:
Transistor:
- 2SC5200 x 10
- 2SA1943 x 10
- 2SD1047
- 2SB817
- TL072 IC
Capacitor:
- 33p x 1
- 0.1uF x 1
- 1uF (105) x 2
- 100uF/50v x 3
- 10.000uF/80v x 4
Resistor:
- 10R/5W x 1
- 150R/3W x 2
- 100R /1W x 20
- 470R x 2
- 1K x 2
- 3K3 x 1
- 5K6 x 3
- 15K x 2
- 15K x 2
- 47K x 1
- 100K x 2
- 250k potentiometer
- Aluminum heatsink (large) x 2
- Mica pads x 22
- Diode 4007 x 2
- Diode Zener 15V x 2
- Diode bridge KBF C3510
- Audio jack connection
- Fuse base and fuse 15A x 2
- Power supply:
** 45V 0 45V AC 1000 watt transformer**
#diyamplifier #sharetechcreative - Наука та технологія
*NOTE: Output (up to 1000 Watt Mono) amplifier circuit*
*This project needs huge aluminum heatsinks, since this is a push-pull amplifier circuit, it works very much depending on your loading (speakers)*
*This is a project that requires advanced knowledge of electronics related to audio. The cost of the project is relatively high. If your knowledge is not at a level where you can understand the project, you may fail and lose a good amount of money*
*If you are a beginner, we recommend starting with less complex and cheaper projects. Gradually you will gain the knowledge needed to make this type of amplifier😊*
Thank you for sharing👍👌💪
Emitor ??
why did mono? :(
P
Q
Cara! que trabalho excelente 👏👏👏👏 o nível de distorção é quase zero 👏👏e isso porque é apenas um canal! imagina com dois canal! Vou montar um pra mim! Mil likes 👏👏👏
Nossa 👏👏👏 de todos os vídeos de amplificadores de potência que eu vi no UA-cam,esse foi o de maior qualidade e potência, muito bom mesmo 👏👏👏👏 excelente! parabéns pelo trabalho 👏👏👏,vou montar um desse pra mim 👏👏
I'm from indonesia 🇮🇩
Wellcome
You are make it
Mantap Om
@@fakirmohandasdas9367 kouthu?
Ja z Polski :D
E muito bom saber que temos oportunidades de fazer um igual
gracias por el circuito!!!!!
you make this look so easy! I bet if i tried it it would turn out more like a welder than an amplifier haha. Lots of sparks
Great video, my cousin already has advanced knowledge in electronics, I'm going to ask him to teach me this project, but would you have the electrical scheme of this circuit?
I noticed that you posted a link with a different layout with pre-tonal and this one in the video has no price, please can you make the layout available? the other link is not working.
Very impressive 👍please upload Driver circuit schematic in description box
with this pair of transistor, what do you prefer, common emitter or common colector; regard sound quality? great amp thamks(:
Thanks for the visit
For such a project you should definitely have an electronic schematic diagram, as well as photos with measurements. (watts, response curve, etc)
Me Indonesia 👍🏻👍🏻
I would like to see multimeter reading's...it looks great!! look like a bunch of watt's? strong! great!
Great suggestion!
How many " of speaker can I use
احسنت.و برك الله فيك...............
Thanks
Exelente muy bueno
watching from malaysia
Thanks for coming
Hello, where can I find the diagram of your amplifier, can you share it, please, thank you
Excelente el proyecto. Me gusto como fue realizado.
Preguntas?
RMS?
Ohms minimo y maximo?
Low, High ó Full Range?
Se podria poner un EQ?
Gracias segui asi con tus proyectos.
Those transistors are massive. I love shit like this.
E super,lam făcut,lucrează perfect
Great, congratulations
this is a nice and interesting project, if someone want to do this type of amplifier as a project in the school
how someone can get your information for explanation and the cost of it
Create a video showing how to modify the amplifier board of a computer speaker ;)
Mamtap bos...
the best and simple amplifier ❤️❤️❤️
Glad you like it!
Muito bom...você tem o projeto desse amplificador???
Circuito complicado, 👍👍👍👍👍.
Wow! Hello my friend! it's amazing! It's wonderful video! Great information for audiophiles! Very useful! Wonderful!
I really enjoyed it! Nice upload! And it's great high quality video! I really like it! Very interesting! Thank you for sharing!
Thanks for visiting
That speaker was hating life with no baffle or back pressure 😂
Bom dia, qual a amperagem desse transformador toroidal que vc usa nesse amplificador com 20 transitores ??
20 Amps
does anyone know, if you doubled the amount of transistors, would it double the power of the amplifier?
Amplificador muito difícil de fazer Ôk, fais um amplificador com 2 transistos 2sa 1943 Ôk
Ok please wait!
@@ShareTechCreative amigo cual es su potencia máxima?
Testing an amplifier is about using a power resistor and measure output voltage to calculate the output power, instaed of the speaker. Vout*Vout/Resistor resistance (Due speaker have impedance, which will act different in every time, unlike a power resistor which is always x amount of ohm. )
Also i can tell its not 1000Watts, due the speaker wires are thin, and its not burning front of camera, its stays cold. (It might be due its on "30% volume") but i would consider use thick cables for this high performance. My guess is that amplifier puts out only 100Watts. Thats why the cables arent burnt.
Hay quá
Thank you
tôi đến từ viêt nam.ngỏ ra sao lại là vcc.cảm ơn
The output of an amplifier to the speaker is 0 volt 16:39
@@ShareTechCreative transitor B.C.E.sao ra bằng chân C của transitor.xin cảm ơn
@@gamingonlinefifahqh1551
Trong mạch amplifier này, nguồn V+ được cấp vào chân E của các transistor 2SA1943 và nguồn V- được cấp vào chân E của các transistor 2SC5200 nên chân C sẽ là chân ra
@@creative102st6 nếu nguồn vào chân c transistor 2sa1943 v-.đổi nguồn vào chân e thì nguồn v+ phải không bạn.cảm ơn bạn
@@gamingonlinefifahqh1551
Thông thường là nguồn (V+) vào chân C transistor 2sc5200 thì chân C của A1943 là nguồn (V-), còn trong mạch amp này nguồn (V+) vào E của A1943 thì (V-) phải vào E của C5200, tóm lại nó có 2 kiểu cấp nguồn tùy theo thiết kế mạch ampli.
Nice 🤗
Hello
Thanks 🤗
What is the resistor with the coil in parallel do I have to make that or can I buy one
Very Nice
18:35 What song were you using to test it?
Nice
Thanks
Very good
Thanks for visiting
This is an amazing project. What is the maximum watts we can use for the speaker?
nice...good job... waiting for schematic diagram...
Thank you
i think you forgot the coil on the part list the one in series with 5w 10 ohm J 10R resistor
Mind blown !! This is such a beautiful and powerful build. One of the best of your designs. Thank you for sharing this powerful and elegant amplifier. Will it be better to have a speaker protection relay as the pop on power on has a push on the speaker (its that powerful). How many heneries is the inductor ? can that be replaced with a output capacitor (35v-2200uf) ?
May i please request you build a similar Class A amp which has huge power just like this one ? Thank you again for your hardwork and for sharing your craft.
Thanks for your information
@@ShareTechCreative you are the best. Thanks
Thank you for sharing your ideas with the rest of the world Please my question is the ground wire connect to the heatsink?
Great work!
Thanks for the visit
Waah kya bat ha
Magnífico trabajo como siempre mi querido amigo.....le mando muchas bendiciones y darle las gracias por su gran labor divulgativa.....una cosa....¿habría posibilidad de conseguir el esquema eléctrico de su montaje?....Muchísimas gracias, un gran abrazo virtual desde Las Islas Canarias (España).............................
Gracias por tus mejores deseos, ¡te lo enviaré!
@@ShareTechCreative ....muchas gracias amigo...cuídate por favor....un gran saludo hermano....
@@ShareTechCreative podes me enviar também... Sou do Brasil... Esquematic
Pudiera también por aquí amigo
una pregunta amigo y colega en el ..... video se mira la conexion de los colectores a la red de sobel las bases estan con su resistenncia de entrada de senal y en los emisores entrann los voltajes positivo y negativo.........es lo que yo veo en el video ....sera posible
Thank you, sir👍
So nice of you
Tiene mucho ruido de fondo el amplificador sin música, ni nada conectado, como se podría solucionar?, saludos
I am from India
Chờ mình Xem với nào hay quá
How to make pre amplifier easy please :)
Can you make another video where you connect the input of the amplifier to a sine wave signal generator, the output to a 4 Ohm load and an oscilloscope then drive it at low level, say about 1 Watt?
Why didn't you use ballast resistors, 5 Watt, 0.5 Ohm on each output transistor? Any mismatch between transistors (and there's always mismatch) will cause distortion. Ballast resistors will help level out the current sharing across mismatched devices.
Thanks for the info, I'll keep this in mind
Very good 👏👏👏
Thanks man
You're welcome!
I'm From VietNamese 🇻🇳
Thanks
Gostei 👍👍👍, já deixei meu like, é isso aí, tem que pôr volume nisso pra gente vê a potência
JOSSS MANTAB
So amazing work❤❤
Thanks 😄
Good🔝🆗🆒🆕
Thanks
Can I use commuted poder supply?
Great you video
Thanks!
O coletor do 5200 pode ser ligado no coletor do 1943? Não há um erro aí? Acho que é ligado no emissor.;;
Você segue as instruções exatamente, vai funcionar bem
@@ShareTechCreative Tenho montado com o emissor do 5200 ligado no emissor do 1943. Essa montagem é estranha para mim. Vou tentar montá-la. Obrigado por me atender,
Obrigado pelo interesse, boa sorte
Sir how to make this heatsink ?
Very nice my friend ! Great amount of power !!! Excellent P.A. amp ! I have a question : I have been having trouble finding , online , this large of heatsink . If you buy online will you please share a link ? Thank you so much . Have a great day !
Not that I know of. Have a great day!
@@ShareTechCreative thank you
No emitter resistors ? Base resistors are good enough ?
You can be adding
what music did you use to test the amplifier?
dj nell - not alone
Super video my friend
Thanks for the visit
muy buen proyecto amigo me puedes mandar el diagrama .......gracias saludos
Thank you, brother, for this valuable circuit, but I hope that you are limited to components and without loss of performance ** With the use of the integrated lm 386 stage of audio input.
I will try my best
Thank you for your effort
Very well done. Its really awesome.
Thank you very much!
What voltage is this amplifier supplied with, please?
In the video description!
Kitne ench ispkar lagega 4spikar wa6
Just what i need excellent project!!
Thanks
Do you have schematic for the amplifier driver of this project? Thankyouuu soo muchc
Greetings sir from Colombia sir what are the chances that you sell that as it is bone hacik echo as promoted by ak in the video
Great amplifier
I love it
Nice Video👍
Whats that white board you're using?
You can use a wood panel.
"It looks so clean"👍 , Thankyou.
👍👍
Thanks for the visit
Hola amigo me gustaria comprar uno de estos amplificadores son artesanal ademas de lo mucho que megusta la electrónica yo lo compro no importa el costo y el envio
im an SOOO glad to have grown up with american music lol :p
olá amigo!Vc tem como me enviar o esquema de montagem desse amplificador de 2000 w?me responde ai???
Yes can
Achei uma montagem parecida com os psl da machine só que nós amplificador da machine não usa as mica já que não vai tenção nós coletores não precisa
WONDERFULL WORK ...
CONGRATULATIONS ... 😃😃😃👍👍👍😜
Thank you so much 😀
Amigo discúlpeme, puedo usar los transistores d718 y el b688 no tengo los otros se me dificulta para conseguirlos
Yes, can
@@ShareTechCreative scuseme muy teacher i have a transforme 44 0 44 AC, un the exit rectific 59 0 59 DC, do yuo belive the posibility ,can i yo use on yuors proyect, sir
The transforme give 21Amp.
El Transformer give posible 18 amo i" can yo use
Super😊
Thank you! 😊
What is that soldering iron.
Please you explain v - you give c 5200 transistor ?
Thank you for your attention, this is also a way to connect, usually, people see that the collector (C) of the transistor is powered, and the emitter (E) will output the signal to the speaker.
For example, The positive source is supplied to the collector pin (C) of the NPN transistor, and in this case, the source is negative, it is completely opposite.
This is also fundamental in the ways of biasing transistors.
Again you should also pay attention to the polarity of the power supply, which powers the amp. and you do it step by step, pay attention to supply the power within the allowable threshold it will work very well and powerfully... Good luck.!
Todo esta bien amigo pero deja el diagrama t lo agradrseria para muchos seria mas facil por lo demás exelente
Iam from indonesian😊😊
Hello, my friend! thanks for visiting!
@@ShareTechCreative 👍👍👍
Dư thừa chỉ cần 3 con là đủ
Sir iska yellomeetar kha par melega
Sir where can i connect the positive supply? In transistor 1943? Or tranaistor 5200? Thanks you!😊
Positive supply to Emitter of A1943 transistors
Thank you😊
Plz one video RF powerful 8 amplifier 5 booster circuit
What is the uh of the conductor/how many turns/guage copper wire, over all very impressive, i would like to give it a try, looks great.
1.2mm copper wire, wound 16 turns with 10 ohms / 5-watt resistor
@@ShareTechCreative thank you very much indeed.
Great 👍👍👍
Thank you 👍
Esquema tem
Amazing sir
Thanks and welcome
I am from Pakistan
U started every simple... But it gt a place I don't gt it anymore
Sirr... How much ohm speaker is that ??? Please reply sir