What is parasitic inductance of your traces on PCB ? How you mitigate that ? Are this traces capable to carry such current at 40 *C ambient all day long ?
@Electronic_For_You then some other MOSFET in parallel heats up To clarify below is the connection i have 6 MOSFET for each side of primary, ie 6 parallel MOSFET(irf1404) for one side of primary winding and another 6 for the order primary winding ...(In ur case u had 4 paralleled..) Input is 30khz, ... 12V
There are lots of things that can make MOSFET heating, Ic failure , check the output signal , and Transformer turns difference between primary half can also make one side MOSFET heating
@@Electronic_For_You yes I checked the gate drive is perfect and symmetrical. The transformer turns ratio 3-0-3 is also right . . Yea my suspect is i used 2mm wire for 3-0-3 , and the winding is not 100% in shape I say. ..may be switch to a small capacity transformer?? Recreated the design with 2 , 4, 6 parallel MOSFET (irf44N, irf3205, also 60n60 igbt ).. but same only 1 heats up in parallel, if I switch the primary sides then another MOSFET heats in the other parallel group I too doubt the low winding resistance and inductance ...
Hello. A very good project and I want to repeat it. As I understand in the description, the cost of a different circuit with an EE28 transformer and a power of 500 watts. What changes need to be made to get a 700-1000 watt inverter?
I have followed the same EGS002 module and EG8010 datasheet schematic of low power frequency transformer for making 500W inverter. Currently I am facing an issue with voltage loss under load condition that is initially when I turn on the Inverter, it starts smooth with 230V 0.5A AC but as I connect the load of 100W its voltage drops to the 110V and starts decreasing gradually. Same issue happening with the drill machine, when I trigger the drill machine voltage starts decreasing. Please help me to resolve this issue, ands feel free to reply if someone faced the same issue previously. Thanks ;)
Hi, I'm looking for an inverter of this type, and I found this one, and it seems like I can use it for my project, I'm from Brazil, there's no one here, can you send me a diagram?
Hello this PCB has Some errors that need to be fixed, there is another Gerber file link in description based on the EE-35 taken from another UA-camr You can Use that PCB 👍
Проделана не малая работа. Есть мелкие огрехи но это стартовый проект как я понял. Защиты не хватает!!! Я делаю подобный проект, но я заморочился с защитой по току. Выложу наверное то-же на обзор.
Да Это мой первый проект синусоидального инвертора! И в этой схеме так много проблем, которые нужно исправить, большинство проблем на вторичной стороне 👍 Я рекомендую вам сделать инвертор на основе модуля SG3525+LM358, который доступен на AliExpress, он решает множество сложных задач.
![DIY Pure Sine Wave Inverter 12V To 220V - 1000W [Full Video] ✓](http://i.ytimg.com/vi/9d4MFQd7ZQg/mqdefault.jpg)
DIY Version With Circuit Diagram on Pinned comment
ua-cam.com/video/9d4MFQd7ZQg/v-deo.htmlsi=Pm8zdAEjelsycHdo
Awesome, for better result on the output use 1.7mH inductor and 3.5uF Capacitor
What is the capacity of the 35 mm core wrapped?
You mean ee-35?
Good job sir ❤
Thanks
HI, how you calculate GATE resistor, and can you show, on sccilloscope
if it is calculated correctly ?
This was a prototype, there were many problems in this circuit,
Good 👋
Thanks
What is parasitic inductance of your traces on PCB ?
How you mitigate that ? Are this traces capable
to carry such current at 40 *C ambient all day long ?
There's some problem in the secondary side , this is a prototype not final project
Very Nice!
Thanks
Very nice
Thanks
Can we have assembled & tested board for sale
Sorry,
Maybe in future
I tried the design but only 1 MOSFET on the the dc side heating up very high , y is that???
What if you remove that 1 MOSFET?
@Electronic_For_You then some other MOSFET in parallel heats up
To clarify below is the connection
i have 6 MOSFET for each side of primary, ie 6 parallel MOSFET(irf1404) for one side of primary winding and another 6 for the order primary winding ...(In ur case u had 4 paralleled..)
Input is 30khz, ... 12V
There are lots of things that can make MOSFET heating, Ic failure , check the output signal , and Transformer turns difference between primary half can also make one side MOSFET heating
@@Electronic_For_You yes I checked the gate drive is perfect and symmetrical. The transformer turns ratio 3-0-3 is also right . .
Yea my suspect is i used 2mm wire for 3-0-3 , and the winding is not 100% in shape I say. ..may be switch to a small capacity transformer??
Recreated the design with 2 , 4, 6 parallel MOSFET (irf44N, irf3205, also 60n60 igbt ).. but same only 1 heats up in parallel, if I switch the primary sides then another MOSFET heats in the other parallel group
I too doubt the low winding resistance and inductance ...
If you switch the primary side and other side MOSFET heats , then it's a Transformer problem,
Hello. A very good project and I want to repeat it. As I understand in the description, the cost of a different circuit with an EE28 transformer and a power of 500 watts. What changes need to be made to get a 700-1000 watt inverter?
Hello
You can check through the first pinned comment you will find video of prototype, you can adjust the wattage as you need,✨
@@Electronic_For_You what should I do to get maximum power?
Should I just use this board and transformer on the EE55?
@УмиджонАлламуратов-м7ы
This circuit is not well optimized, I recommend using the SG3525+LM358 Module
It's inverter only! Without battery charging?
Yes
Beautiful, but your tester mesures 10-times different value.
Look at datasheet of this MOSFET,
sir how to order board like that to you
From JLCPCB website
@@Electronic_For_Yousir the file you uploading in gerber not working plss send me a diagram sir 🙏to make my own pcb in jlcpcb im yung subscribers sir
Check the pinned comment
@@Electronic_For_You sir do you have a facebook account?
do you have a facebook sir?@@Electronic_For_You
I have followed the same EGS002 module and EG8010 datasheet schematic of low power frequency transformer for making 500W inverter. Currently I am facing an issue with voltage loss under load condition that is initially when I turn on the Inverter, it starts smooth with 230V 0.5A AC but as I connect the load of 100W its voltage drops to the 110V and starts decreasing gradually. Same issue happening with the drill machine, when I trigger the drill machine voltage starts decreasing. Please help me to resolve this issue, ands feel free to reply if someone faced the same issue previously. Thanks ;)
I never had this problem, I think the issue is your transformer
Is your feedback circuits okay
Because it's related to feedback issue
Nice
Thanks
Hello friend I rewinde core but mosfet hot without load can you tell me which frequency use here
try using 30-40khz
How to get this pcb from you.
You can order from JLCPCB
Please schematic.
First comment
Hi, I'm looking for an inverter of this type, and I found this one, and it seems like I can use it for my project, I'm from Brazil, there's no one here, can you send me a diagram?
Aye, engineer. Did you design a 2-layer file?
No sorry
Circuit diagram?
First comment
i need schamatics
It's in video
Schematic lm358?
ua-cam.com/video/HhRgXBVkSgs/v-deo.htmlsi=pUVAIUO6LJrIWhSl
@@Electronic_For_You thanks
@@Electronic_For_You fantastic
You are welcome,
And Use 4 turns winding for the EGS002 module , 12v and 5V supply
boss ap ki ye geber file upload krni or same aisi pcb hume mile gi right ? pls cnfrm kr dena me ne same inverter bnana hai
Hello this PCB has Some errors that need to be fixed, there is another Gerber file link in description based on the EE-35 taken from another UA-camr You can Use that PCB 👍
@@Electronic_For_You bhai hindi me bta do
@@Electronic_For_You bhai ap ne jo old inverter bnaya tha kya wo pcb sahi hai ? kya hum same wo bna skte ?
Sorry I don't know,
What you want to say , Please can you tell me your problem in English so I can solve it !
I cannot translate your comment!
I have Updated the link ,
There is a different version of PCB based on EE-35 Transformer and everything is same
Проделана не малая работа. Есть мелкие огрехи но это стартовый проект как я понял. Защиты не хватает!!! Я делаю подобный проект, но я заморочился с защитой по току. Выложу наверное то-же на обзор.
Да Это мой первый проект синусоидального инвертора! И в этой схеме так много проблем, которые нужно исправить, большинство проблем на вторичной стороне 👍
Я рекомендую вам сделать инвертор на основе модуля SG3525+LM358, который доступен на AliExpress, он решает множество сложных задач.
لا توجد pcb للمشروع
Hello,
There are some problems in my PCB you can try this improved PCB (EE35)
drive.google.com/file/d/1XE8lxa76rcEoItWQ4dki0yfskfhJ20tH/view
I want this pcb
Order from JLCPCB website
Wrong wire selection and core
Diagram send
Video Description
good job friend can you tell me your whats app number
Ask any questions here!