Love it! Just ordered 20. I love flying drones and this really helps make custom battery packs. Your work is loved and respected, I hope you're making the money.
The most interesting thing for me is that all the videos show how they launch this board with 5+ volts, but no one shows that it works better with 4.4v with lower heating.
There are some losses you need to consider and exact 4.2 or 4.4v doesn't make sense to create for a charger as "more complexity" Here he used a bench power supply so it was possible And we always charge battery with +2v. I.e for 12v we use 14v or 15v charger
Przy prądzie 1A układ TP4056 grzeje się mocno, nie warto przekraczać tej wartości bo długo to nie popracuje.// At a current of 1A, the TP4056 system heats up a lot, it is not worth exceeding this value because it will not work for long
It will not work for long hot glued to a piece of wood but if there is space under the module for air circulation and maybe even a fan it will stay cool and work for a long time.
O que não diz o vídeo, se houver uma falha no potenciômetro no caso o trimpot por um momento seguer o ci terá corrente máxima excedendo o suportado e queimará, por isso no projeto é um resistor fixo, mas com um arranjo simples em chavear outros resistores em paralelo isola totalmente um provável incidente...
@@ZAFERYILDIZ52 vi um vídeo há alguns anos gringo que fez com um potenciômetro e daí momento houve uma falha deixando o circuito aberto sem resistência o CI adota corrente máxima e queima...
Я совсем не знаю ихние язык, но я хорошо понял что он имеет ввиду! Теперь мне кажется что я знаю его язык. Мне как раз пригодился этот способ Я слегка понизил потребление заряда. благодарю автор за информацию!⭐⭐⭐⭐⭐
@@sanfrrraa Can you explain why not? Because as I understand it two devices with no potential difference will give no current flow, or maybe I'm wrong?
When you say the charging current is one amp does that mean that the TP4056 module only changes the voltage (from 5.20'ish to 4.20) like a PWM solar controller and not like an MPPT that takes the energy input and converts it to a the battery charging voltage while (in the case of most MPPT's that reduce voltage) increasing the current?
The Tp4056 is a very intelligent battery charger. Between a battery voltage of 3V and 4V it charges at 1A. If the battery voltage is lower than 3V it charges with very small Amps to get the battery to 3V If the battery is about 4V, it lowers the amps step by step until the battery is at about 4,2V It stops charging when the battery is full. If you change the value of the resistor R3, you can get the charging current between 3V and 4V from 1A down to 0,2A.
@@Sinista123 Ciao Sinista123. Ho delle 18650 da 700-800 mAh. Posso caricarle anch'esse col TP4056 1A? O me le incendia ? Grazie in anticipo per la tua attesa risposta. Antonio
@@AntonioANT-z7c If it's only one single 3,7V 700mAh Lithium ion battery, then 1A is maybe a little to much. You should charge them with somewhere between 0,5 and 1 times the capacity of the battery. It's possible to modify the old micro USB version of the Tp4056. This version has a bigger R3 resistor. Replace the resistor R3 with a 2K Ohm resistor or try to find someone who does it for you. 4k Ohms is about 300mA charging 3k Ohms is about 400mA charging 2k Ohms is about 580mA charging 1.66k Ohm is about 690mA charging 1.5k Ohm is about 780mA charging
@@Sinista123 Ciao Sinista123. Grazie davvero di cuore. Le resistenze di cui parli, oltre ai K Ohm, hanno anche una sigla per le loro dimensioni? Vorrei comprarle evitando di sbagliare... Buona giornata.
@@AntonioANT-z7c You can use standard ¼W resistors or smaller. It doesn't need to be perfect. I would use 2x standard 1K Ohm resistors, put them next to each other and twist the ends of one side together. Then use both ends on the other side and replace the resistor R3 on the micro USB version of the Tp4056 with that. I would not get the USB-C version of the Tp4056. Because the resistors on the USB-C version are so small, it's almost impossible to replace them with something else. If you want to use USB-C, you can get a USB trigger board and set it to 5V and then connect it to the 5V input of the Tp4056. Then it should also work with every modern USB-C charger.
Hi can you explain why if we charging the battery in tp4056 with load on it will damage the tp4056 module .. and how we can charge the battery while the load is on is there any solution to charge and using load together Best regards .... mousa Alabbasi
Selamünaleyküm Zafer hoca çok güzel bahsetmiştim de yalnız ben sizden başka bir şey soracağım örneğin bir tane tp4056 kullanıp aynı anda 7-8 tane 18650 lityum batarya şarjlı paralel bağlayıp şarj edebilir miyiz Yani çıkış amperini 5amper yapabilir miyiz bunun için hangi komponentleri üzerinden değişmemiz gerekiyor veya aynısını yeniden yapmamız gerekirse nasıl yapabiliriz
Buena idea para reducir el amperaje para cargar baterías que lo ameriten, pero aumenta el amperaje no es bueno porque el modulo con 1 amperio se calienta demasiado
2:56 Hi, Zafer Yildiz. Thank you, very much for doing interesting video. Can you explain how to connect a Li-Ion 72V=40A BMS in a 36V-40A Li-Ion battery? I tell you, it is possible, since we do it here in Mayari, Holguín, Cuba. Thank you very much I see all your videos, they are jewels. It's been a pleasure. Joakin
Merhabalar Zafer bey. Elimde trimpot bulunmadığı için kısa süreli kullanım amacıyla normal potansiyometre kullansam sakıncası olur mu acaba? Şimdiden teşekkürler.
@@alexps6463то линейный преобразователь, при 4.5 гарантированно все испытуемые платы нормально работали, отдельные экземпляры даже при 4,3 нормально заряжали.
I want that when the battery reaches full charge, the current doesn't cut off. The current should continue to flow at 4.2V. This is because the current cuts off at 4.2V, but the battery voltage drops to 4.15V or 4.1V, and after that, if the current continues for some time, the battery will be fully charged. Is there any method for this?
lipoyu 1a ile şarj etse ne olcak? yada yani 0.2a ile optimum şarj oluyor ise batarya, bunu nasıl bileceğiz? elimdeki bataryanın kaç a ile şarj olacağını nasıl bileceğim?
Sir! Nice video. Can you please help me to fix my Bosch bms Li5s4l01 board for bosch vacuum cleaner 14.4v. Apparently there is issue with a circuit. I have taken picture for it. Can you please help me find a replacement one. How can I contact you for help!
This is only relevant for Lithium (LiPo) batteries. But yes depending on the C-value of a battery you should charge the LiPo with different current so that it will not be charged to fast!
Hocam merhabalar. Elimde tp4056 modülü var bu modüle 18650 pil bağlıyorum çıkışından olması gerektiği gibi 5 volt veriyor. Bana 6.5 volt bir çıkış lazım mutlaka voltaj yükseltici devre kullanmam lazım mıdır yoksa bu devre üzerinde bir değişiklik yaparak çıkış voltajını 6.5 volta ayarlayabilir miyim?
zafer abi lifepo4 piller icin maksimum şarj gerilimi 3.7 volt olması gerektiğini duydum. bu devre üzerinde bu şekilde bir oynama yapabilir miyiz. yavaş yavaş bu pillerle karşılaşmaya başlıyoruz. tp4056 üzerinden bir çözüm bulursak gayet kullanışlı olur diye düşünüyorum.
Тогда какой смысл брать для этого явно неподходящую плату? Просто бери промышленный зарядник и заряжай чё хошь. Тут он просто поделился, как из говна сделать чуть более полезное говно.
Идея хорошая только не там автор ток заряда смотрит! или только настоящие мастера заметили? (у него на блоке питания лабораторном показывает не ток заряда, а ток по 5-вольтовой питающей линии)
Дійсно, але погрішність невелика. На БЖ показує зарядний струм плюс струм власного вживання контролером заряду. Вважаю що він невеликий, тому їм можно нехтувати. Так що по більшому рахунку вимір коректний і відповідає дійсному струму заряду.
Это линейный стабилизатор. Так что 99% тока проходит через него до аккумулятора. Разница между 5В на входе и напряжении АКБ на выходе - рассеивается в виде тепла.
Спасибо! Возьму на заметку!👍
возьми в рот
Love it! Just ordered 20. I love flying drones and this really helps make custom battery packs. Your work is loved and respected, I hope you're making the money.
Zafer, красавчег!
That Good and Number one for you ❤❤❤❤
Thank you very much for your comment and support.
Thank You!!!!!!!!!!
💚💛💙🤍
His video is very much clarified!
The most interesting thing for me is that all the videos show how they launch this board with 5+ volts, but no one shows that it works better with 4.4v with lower heating.
Be that as it may, You can find 5V USB supply pretty much everywhere. You can't find 4.4v though.
Apples and oranges.
There are some losses you need to consider and exact 4.2 or 4.4v doesn't make sense to create for a charger as "more complexity"
Here he used a bench power supply so it was possible
And we always charge battery with +2v. I.e for 12v we use 14v or 15v charger
Przy prądzie 1A układ TP4056 grzeje się mocno, nie warto przekraczać tej wartości bo długo to nie popracuje.// At a current of 1A, the TP4056 system heats up a lot, it is not worth exceeding this value because it will not work for long
It will not work for long hot glued to a piece of wood but if there is space under the module for air circulation and maybe even a fan it will stay cool and work for a long time.
Great video again.
I need to fabricate an 8 AA cells battery charger, sny idea on what module or circuit could I use.?
Clamping a board over its components (0:08) is not a very good idea.
Спасибо. Хорошее видео. Очень полезно.Thank you. Good video. Very helpful.
Спасибо за ваш комментарий и поддержку.
Технічно відео не коректне !!!
@@СергійЯловенко-е7зWhy?
brother i want to charge my batteries up to 4v instead of 4.2 using tp4056 pls help
THANKS, ZAFAR IS BOSS IN ELECTRONICS👍
Creative video, thanks :)
Thanks for video 🙂 Could You make more videos about such circuits Mr Zalpher?
ilmu yang sangat bermanfaat, terima kasih videonya bagus
Çox sağol Zafer Yıldız.
Teşekkürler. 👏👏👏
That good 👍❤️🤪
Thank you for letting me know useful information.
Whow !!!! you are great !!! many thanks Zafer!!!!
Thanks! You inspired me, I'm already ordering components.
T4056 uses linear regulation. Meaning anything greater than 1Amp makes it extremely hot.
just using a small heatsink, its simple & work very well
Wow . How simple! Thank you!
O que não diz o vídeo, se houver uma falha no potenciômetro no caso o trimpot por um momento seguer o ci terá corrente máxima excedendo o suportado e queimará, por isso no projeto é um resistor fixo, mas com um arranjo simples em chavear outros resistores em paralelo isola totalmente um provável incidente...
👍❤
@@ZAFERYILDIZ52 vi um vídeo há alguns anos gringo que fez com um potenciômetro e daí momento houve uma falha deixando o circuito aberto sem resistência o CI adota corrente máxima e queima...
@@ZAFERYILDIZ52você é português??
A fixed resistor should be used in series with the trimpot to limit the maximum current.
последовательно ставишь 1,2 ком и все
Também gostei Luiz, valeu 😉👍
Я совсем не знаю ихние язык, но я хорошо понял что он имеет ввиду! Теперь мне кажется что я знаю его язык. Мне как раз пригодился этот способ Я слегка понизил потребление заряда. благодарю автор за информацию!⭐⭐⭐⭐⭐
You have a regulated power supply, using it you can easily charge any battery...
It's two different things by myself.1st only adjustable power source,2nd circuit board which knows (programed) how to charge Li ion battery correct)
The power supply won’t stop charging when the battery is fully charged.
@@mikebond6328 actually it will! if you set the voltage to 4.2 it will stop there :)
@@clausqp no it doesn't
@@sanfrrraa Can you explain why not? Because as I understand it two devices with no potential difference will give no current flow, or maybe I'm wrong?
Good job ever
Puedes modificar el voltaje de carga/descarga ? Para usar la bateria entre 20%-80% (3,5v-4v?) Seria interesante un video asi
Thanks. I didn't realise one of those pads was just GND. Much easier than trying to connect to 2 SMD pads.
How to edit voltage??
Puedes desmontar la resistencia variable, medirla y sustituir la resistencia por una smd fija y quedará más curioso. Gracias X tu
There is a chart for the tp4056 that shows how much resistance to use for specific amperage. You can find it on google.
Merhaba ustam ben bu devre ile bir lityum pili şarj ettim pil 4.8 volta ulaşmasına rağmen mavi ışık yanmadı kırmızıda kaldı neden olabilir sizce
great thanks
Zafer bey voltaj ayarını nasıl yapabiliriz örnek olarak lifepo4 pil şarj etmek istiyorum
Me too
Super Video Sir Amazing
Excelente la explicación sobre tradear BTC con otros pares y viceversa. Saludos
Ciao Zafer. Col tp 4056 posso caricare anche una litio 21700 ?
Excelente.🇧🇷
To reduce the heat dissipation of the 4056 chip, you need to apply no more than 4.6-4.8 Volts to the input. 🖖
Excellent job
Sangat keren 👍👍👍
Eline sağlık kardeşim peki daha düşük ma ile şarj etmek istersek kaçlık trimpot kullanmak lazım
Видео 👍 пожалуй скачаю .
Great
Genial Ing.
Is possible to limit charging voltage, to stop charging for example on 4.15V?
I need the same information also. Thank You!
How about adjusting the voltage output to charge 4v lead acid battery, can it be done?
I have a 10000mah battery, I want to charge it using the tp4056 module, what resistor value can I put at the charge limit resistance?
Так и менять ничего не надо. На плате и так стоит резистор на максимальный ток заряда 1A.
Merhaba Zafer bey gerilimi düzenleyip lifepo4 pilleri şarj etme imkanı var mı?
Very good
When you say the charging current is one amp does that mean that the TP4056 module only changes the voltage (from 5.20'ish to 4.20) like a PWM solar controller and not like an MPPT that takes the energy input and converts it to a the battery charging voltage while (in the case of most MPPT's that reduce voltage) increasing the current?
The Tp4056 is a very intelligent battery charger. Between a battery voltage of 3V and 4V it charges at 1A.
If the battery voltage is lower than 3V it charges with very small Amps to get the battery to 3V
If the battery is about 4V, it lowers the amps step by step until the battery is at about 4,2V
It stops charging when the battery is full.
If you change the value of the resistor R3, you can get the charging current between 3V and 4V from 1A down to 0,2A.
@@Sinista123 Ciao Sinista123. Ho delle 18650 da 700-800 mAh. Posso caricarle anch'esse col TP4056 1A? O me le incendia ? Grazie in anticipo per la tua attesa risposta. Antonio
@@AntonioANT-z7c If it's only one single 3,7V 700mAh Lithium ion battery, then 1A is maybe a little to much.
You should charge them with somewhere between 0,5 and 1 times the capacity of the battery.
It's possible to modify the old micro USB version of the Tp4056.
This version has a bigger R3 resistor.
Replace the resistor R3 with a 2K Ohm resistor or try to find someone who does it for you.
4k Ohms is about 300mA charging
3k Ohms is about 400mA charging
2k Ohms is about 580mA charging
1.66k Ohm is about 690mA charging
1.5k Ohm is about 780mA charging
@@Sinista123 Ciao Sinista123. Grazie davvero di cuore. Le resistenze di cui parli, oltre ai K Ohm, hanno anche una sigla per le loro dimensioni? Vorrei comprarle evitando di sbagliare... Buona giornata.
@@AntonioANT-z7c You can use standard ¼W resistors or smaller.
It doesn't need to be perfect.
I would use 2x standard 1K Ohm resistors, put them next to each other and twist the ends of one side together.
Then use both ends on the other side and replace the resistor R3 on the micro USB version of the Tp4056 with that.
I would not get the USB-C version of the Tp4056. Because the resistors on the USB-C version are so small, it's almost impossible to replace them with something else.
If you want to use USB-C, you can get a USB trigger board and set it to 5V and then connect it to the 5V input of the Tp4056.
Then it should also work with every modern USB-C charger.
Hi there. What is the max Amps you can adjust it to?
1A
Hi can you explain why if we charging the battery in tp4056 with load on it will damage the tp4056 module .. and how we can charge the battery while the load is on is there any solution to charge and using load together
Best regards .... mousa Alabbasi
Good ❤
Nice video! How can I change the output voltage? I want to use it for a remote controller Flysky. I need 6v on output
U can't. U should use voltage booster
i think you need a Step Up Converter like the MT3608
Selamünaleyküm Zafer hoca çok güzel bahsetmiştim de yalnız ben sizden başka bir şey soracağım örneğin bir tane tp4056 kullanıp aynı anda 7-8 tane 18650 lityum batarya şarjlı paralel bağlayıp şarj edebilir miyiz Yani çıkış amperini 5amper yapabilir miyiz bunun için hangi komponentleri üzerinden değişmemiz gerekiyor veya aynısını yeniden yapmamız gerekirse nasıl yapabiliriz
The data sheet recommends charging no more than two cells with one tp4056 module.
Buena idea para reducir el amperaje para cargar baterías que lo ameriten, pero aumenta el amperaje no es bueno porque el modulo con 1 amperio se calienta demasiado
eller dert gormesin arkadasim sagolasin
❤👍👍👍 from 🇮🇩
2:56 Hi, Zafer Yildiz. Thank you, very much for doing interesting video. Can you explain how to connect a Li-Ion 72V=40A BMS in a 36V-40A Li-Ion battery? I tell you, it is possible, since we do it here in Mayari, Holguín, Cuba. Thank you very much I see all your videos, they are jewels. It's been a pleasure. Joakin
Thank you. May you show us how to adjust voltage on this module. Thx in advance
I need the same information also please Mr Zafar, Thank You!
Buen video - Pregunta: ¿Puedo cargar una batería de litio 1450 con el cargador TP4056?
Gracias por su tiempo
Спасибо большое за информацию.
Merhabalar Zafer bey. Elimde trimpot bulunmadığı için kısa süreli kullanım amacıyla normal potansiyometre kullansam sakıncası olur mu acaba? Şimdiden teşekkürler.
A trimpot is a potentiometer.
And this sentences are some bad because my English is some bad and i'm using translate of Google.
Если питать от лабораторника, то питание лучше выставить 4.5В, будет меньше нагрев.
Если регулятор может работать нормально с падением 0.3В, то да
@@alexps6463то линейный преобразователь, при 4.5 гарантированно все испытуемые платы нормально работали, отдельные экземпляры даже при 4,3 нормально заряжали.
Спасибо за видео, дёшево и сердито. Будем использовать.
Can't soldering in right side on R3 ?left side soldering good but the right isn't
Emeğine sağlık ustam bunu el fenerlerinin bataryalarına 18650 pil takarak tp4056 modülü ayarlayabilir miyiz
I miss you measuring output voltage.
He didn't, after reading some of the comments I will be testing to see after I change the resistor.
Обычно при таком токе 1а, чип дико греется начинает и ток начинает падать. Но подсоединил он резистор странно у меня как положено в стоке схемы
За звичай, на вхід даємо від 4,4-4,6 Вольт, температура дуууже знижується. Перевірено роками 🖖
Окэй умняшка, как нибудь зазвичаю😊...если ты мне говна не желаешь...то вам лай и подписка
Bununla gopro endero batarya şarj edilebilirmi
can we do the same on output side
I want that when the battery reaches full charge, the current doesn't cut off. The current should continue to flow at 4.2V. This is because the current cuts off at 4.2V, but the battery voltage drops to 4.15V or 4.1V, and after that, if the current continues for some time, the battery will be fully charged. Is there any method for this?
lipoyu 1a ile şarj etse ne olcak? yada yani 0.2a ile optimum şarj oluyor ise batarya, bunu nasıl bileceğiz? elimdeki bataryanın kaç a ile şarj olacağını nasıl bileceğim?
i think TP4056 will be ultra hot if you rise the charging current
Evet 1.3 amperin üzerine çıkmayın hatta soğutucu ekleyin
Yes, do not exceed 1.3 amps and even add cooler.
Add a heatsink, it'll work, stick it on with an silicone thermal paste that's also an adhesive
Это было не вольт а ампер
Sir! Nice video. Can you please help me to fix my Bosch bms Li5s4l01 board for bosch vacuum cleaner 14.4v. Apparently there is issue with a circuit. I have taken picture for it. Can you please help me find a replacement one. How can I contact you for help!
This is only relevant for Lithium (LiPo) batteries. But yes depending on the C-value of a battery you should charge the LiPo with different current so that it will not be charged to fast!
Hocam merhabalar. Elimde tp4056 modülü var bu modüle 18650 pil bağlıyorum çıkışından olması gerektiği gibi 5 volt veriyor. Bana 6.5 volt bir çıkış lazım mutlaka voltaj yükseltici devre kullanmam lazım mıdır yoksa bu devre üzerinde bir değişiklik yaparak çıkış voltajını 6.5 volta ayarlayabilir miyim?
Nice
Is there a way to set the tp4056 to say only charge an 18650 battery up to 4.00volts only
max voltage is 4.2v if you want to stop the charging in 4v monitor it using multi tester or voltmeters
zafer abi lifepo4 piller icin maksimum şarj gerilimi 3.7 volt olması gerektiğini duydum. bu devre üzerinde bu şekilde bir oynama yapabilir miyiz. yavaş yavaş bu pillerle karşılaşmaya başlıyoruz. tp4056 üzerinden bir çözüm bulursak gayet kullanışlı olur diye düşünüyorum.
4.2 а не 3.7
which one to use. 3296w 10k
Zafer ustam 8610 bağlantılarını yaptım ama ses gelmiyor neden olabilir
comment modifier ma securité de decharge ??? moi je veux deconnecter les consomateurs quand la batterie descent a 3V
Make a video on voltage adjuster please
Aku pake batre 3 beda kapasitas di rangkai 3s pake tp4056 3 biji di paralel kok langsung jebol tp4056 ny bang solusi dong
Лучше бы не регулятор тока, а порог напряжение регулировать. Что бы заряжать действительно разные аккумуляторы.
Тогда какой смысл брать для этого явно неподходящую плату? Просто бери промышленный зарядник и заряжай чё хошь. Тут он просто поделился, как из говна сделать чуть более полезное говно.
И что? Ты будешь вливать 5 ампер в аккумулятор, который рассчитан максимум на 0,2 ампера?
порог напряжения зашит в данную микросхему
@@martinger в этом и проблема
@@bratecyo почему же проблема? Для этой цели есть другие микросхемы. Причем, значительно эффективнее.
teşekkürler
Si se calienta bastante tube que agregarle un disipador de aluminio
Hello sir, I am your regular visitor. How to charge a 3.80 volt lithium battery with this module, ie the cutout will be 4.35 volt.
عالیه اولین کامنت
با تشکر
I like Zafer Yildiz video. But I can't watch it because the music confused me. It's loads and noisy
Ползунок звука есть ?😊
Posso usar essa plaquinha TP4056 para carregar um Pack de 6v
Not. Because the charging current stops at 4.2 V .
Идея хорошая только не там автор ток заряда смотрит! или только настоящие мастера заметили? (у него на блоке питания лабораторном показывает не ток заряда, а ток по 5-вольтовой питающей линии)
Дійсно, але погрішність невелика. На БЖ показує зарядний струм плюс струм власного вживання контролером заряду. Вважаю що він невеликий, тому їм можно нехтувати. Так що по більшому рахунку вимір коректний і відповідає дійсному струму заряду.
Это линейный стабилизатор. Так что 99% тока проходит через него до аккумулятора. Разница между 5В на входе и напряжении АКБ на выходе - рассеивается в виде тепла.
ölçtüğünüz akım, güç kaynağından şarjöre giden akım değil mi? bunun şarjörden battery ye giden akımla aynı olduğunun garantisi nedir?
Вопрос к автору видео... А если подстроечник в ноль закрутить по нечайке.... Микруха выдержит? Думаю, нет.
значит, надо впаять ограничительный резистор
Is it possible to convert to use at 8.4v?
No. You only control the current. Not voltaje. Check datasheet ic