I bought a couple of the Wemos D1s for the same reasons you talk about but had a hard time figuring out how to work with it. Your videos cleared everything up, thank you!
YOU my fine man, have given a good and very insigtful tut. of this board. It's a LOT of info regarding this board out there, but none addressing the real problems like You. I have taken the liberty to share Your vid. with struggeling programmers on some m. boards, where these problems have been addressed recently. Nicely put together, accurate info & good dictation....You really know Your stuff.. Respect..
At first I had a bit of a hard time following your steps and reading the blurry tiny font on the screen but at the end it was very helpful and got my board connected and working thanks to you.
THANK YOU!! This is this the the perfect program to just make sure the board is working. And you showed all of the little steps that are required but not obvious. Thank you sooooo much!!!
Hi, I saw 5V power output as same as UNO. Can we work use this 5V to sensors than back to Digital Input with 5V? As I know ESP8266 only can work with 3V3. Thanks.
If i connect the ESP8266 D1 board to the WIFI at home can i just run any code on arduino IDE after and then view the results on a web browser with the IP address from the board?
DEAR SIR, I WANT TO CONNECT A FINGER PRINT MODULE TO THE WESOM D1 R2 BOARD. I USE THE ADAFRUIT LIBRARY EXAMPLES. IT CAN'T DETECT THE MODULE. WHAT ARE THE PINS TO CONENCT TX AND RX OF THE MODULE? HOW TO WRITE THE CODE?
I have R2 version of the board and found that the boards listed in the Arduino core json for version 2.5.0 only showed R1... Installed beta 3 version and can now select R2 board from the list (as well as mini and R1) Everything now working as expected (blink and wifi scan)
Sketch uses 257316 bytes (24%) of program storage space. Maximum is 1044464 bytes. Global variables use 26816 bytes (32%) of dynamic memory, leaving 55104 bytes for local variables. Maximum is 81920 bytes. Serial port not selected ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,I have this error in the Blink also I turn off the windows security
I bought a couple of the Wemos D1s for the same reasons you talk about but had a hard time figuring out how to work with it. Your videos cleared everything up, thank you!
YOU my fine man, have given a good and very insigtful tut. of this board.
It's a LOT of info regarding this board out there, but none addressing the real problems like You. I have taken the liberty to share Your vid. with struggeling programmers on some m. boards, where these problems have been addressed recently.
Nicely put together, accurate info & good dictation....You really know Your stuff..
Respect..
Thank you for your nice words and comment.
At first I had a bit of a hard time following your steps and reading the blurry tiny font on the screen but at the end it was very helpful and got my board connected and working thanks to you.
THANK YOU!! This is this the the perfect program to just make sure the board is working. And you showed all of the little steps that are required but not obvious. Thank you sooooo much!!!
Vielen Dank, Sie helfen mir sehr, denn die gute und einfache und langsame Präsentation ist gut zum Lernen und Üben. Danke nochmal.
A very big help to me because I'm having a problem finding the right board on board manager..thank you so much
A small issue I faced. In serial monitor also you need to choose baud rate as 115200 on bottom right, else text shown is not readable.
Hi, I saw 5V power output as same as UNO.
Can we work use this 5V to sensors than back to Digital Input with 5V?
As I know ESP8266 only can work with 3V3.
Thanks.
So straight to point clearly . very nice sir
If i connect the ESP8266 D1 board to the WIFI at home can i just run any code on arduino IDE after and then view the results on a web browser with the IP address from the board?
Excellent video. Easily understood, clear and concise.
Thank you so much!!!! Good people make a difference!
DEAR SIR, I WANT TO CONNECT A FINGER PRINT MODULE TO THE WESOM D1 R2 BOARD. I USE THE ADAFRUIT LIBRARY EXAMPLES. IT CAN'T DETECT THE MODULE. WHAT ARE THE PINS TO CONENCT TX AND RX OF THE MODULE? HOW TO WRITE THE CODE?
இதே வீடியோவை தமிழில் வெளியிட்டால் பயனுள்தாக இருக்கும் சார்.
I have R2 version of the board and found that the boards listed in the Arduino core json for version 2.5.0 only showed R1... Installed beta 3 version and can now select R2 board from the list (as well as mini and R1)
Everything now working as expected (blink and wifi scan)
nice video! Is there one that shows how to setup RPi to this borad?
very good lectures
UPDATE: If installing ESP8266 Community version 3.0.0 (the latest), then select Board: "LOLIN (WeMos) D1 R1"
Sketch uses 257316 bytes (24%) of program storage space. Maximum is 1044464 bytes.
Global variables use 26816 bytes (32%) of dynamic memory, leaving 55104 bytes for local variables. Maximum is 81920 bytes.
Serial port not selected ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,I have this error in the Blink also I turn off the windows security
Hello, these my error
Tarjet d1 (plataform esp8266, empaquetado esp8266) no found
I go to device manager its not show CH 340 USB
Can we Switch 3.5 to 5 V
Sir ack and wifi module led not blinking on my board what will be the reason ?
sir can u tell me how to connect wemos d1 with mobile using esp8266 wifi
Thank you, you help me a lot becourse of the good and easy and slow presentation iT,S good for learning and practising. Thank you Again.
Thanks for the helpful tutorial
why do we have to change the speed sir?
in serial monitor what is the baud rate to be set?
Hi Saravanan AL, thanks very much, it is so fun
Hello. Great video. The link to the code does not work
used on D1 is CH340 its not show to me port
You're my hero.
Super, thank you very much for this tutorial.
Excelente, facil y sin complicaciones , In spanish please in colombia many people
Thank you so much .It's useful.
Thanks for the explanation
pleasea the settinkgs are same for D1 R2 with D1 r1??
No, different board; see this video: ua-cam.com/video/hPBVMCfOzr8/v-deo.html
Can you share digital pin mapping?
my port is not opening what i have to do open the port
GREAT VIDEO THANK YOU
Great video, thank you
nice video. Thank you so much
Thank you
my savior
thanks
Why only one analog pin in both nodemcu and this board ?.. So how can we connect multiple analog sensors to the board if required ??
One suggestion would be to get an analog multiplexer.
Thank for heppy
Awesome
Gracias...
Nice boy
thanks boy
Thank you so much!!!! Good people make a difference!
I have D1 version maby there is problem with USB cable because it show only red induction
I plug in Arduino but it not show in portable device CH340
Thank you