Just fitted them yesterday what a difference they make absolutely amazing what a difference when reversing last night. Thanks Simon and the team brilliant idea cheers Carl
Most modern cars are the same regarding the reverse light output, they're terrible. All they seem to do is show a white light at the rear so other road users can tell you are reversing. Nice video and nice kit too, well done.
Just fitted these, the video instructions are great, thank you. I did find a surprise electrical connection when removing the passenger rear light cover, it has what looks to be an antenna stuck to the back of it with a small coaxial cable clipped to the back of the trim also. It didn’t hinder the fitting but it occurred to me that it would be awkward to upgrade these trims to the chequer plate versions you have. I wonder if the antenna is the wireless phone booster that was fitted on my 2022 110 HSE Commercial 300D. I have images if you need them, thanks again
Hi 🙋♂️ much better than the factory fitted specially good in off road dark area where is no light 💡 but I think it’s nice if they come with black glass instead white and matching with the rear lights. Even this is nice 👍 too. Good upgrade. Thanks 🙏
Fitted this kit this morning. Easy job, just wish my fingers were a bit thinner ! Thanks for the idea and materials. Great result. Regards Non Stick Nick
LOVE the product and appreciated Simon & Tyler's video. Here's some pointers from my experience. I have a 2022 MY 110 in the US. Dynamic-HSE. There was an aerial in the left quarter panel. It easily unclipped at the purple bottom connector. Take it to a bench and pry apart the bracket it's on. It's only 2-sided tape. Be careful. Remove residue and apply new 3M tape to the new quarter panel if doing at same time. If not, just disconnect if keeping same quarter panel. Tips from my install. 1) I used heat shrink connectors. 2) For the quarter panel to re-attach, those fat connectors REALLY have to be out of the way. It's a tightish fit, but it eventually works. 3) The black backing (the one with the double sided tape) did not work for me if I put it in before the quarter panel. REALLY jam it to the in-board side, but still not enough room. I added it after. More of a fiddling, we'll see if it stays secured. 4) I don't think it was clear (to me!) but you need to return the two part trim. I saved the back, but painted the bottom. I thought the new backing would screw onto it. Unfortunately, without the old backing there was nothing to screw onto. I double side taped it. We'll see how long before I have to sacrifice that back trim! In use it is a GREAT upgrade. Highly recommend getting this product. Keep bringing New Defender upgrades, PowerfulUk!!
Hi - Are you in the US - I think the extra antenna is on USA models. We have some new molded mounts coming out soon - I am sure we can upgrade you to these if your current ones have problems. Thanks for the tips.
I would recommend that you use heat shrink over the connectors to seal them against water ingress also I would do the same with the unused wiring in the harness
Simon, just received a kit and the LEDs included have three leads so you have both white and amber colors available. I’m thinking that I might wire the amber to either the turn signals or the rear fog lights. What do you think of this idea?
This is a great little up grade. I did have a issue with the stainless steel screws, I found them a touch too long. They pushed the assembly away from the main panel when tightening up. Cut a couple of mm off the end and was good to go.
Hi - thanks for the feedback we will take a look at this. Crazy that the standard reverse lights are not enough to see with the cars own reverse camera system !
I've ordered the wide wheel arch for the new 90, according to landrover fitting instructions I need to remove the lower door trim to fit arches. l was just wondering if it's really necessary, and if so which replacement clips will I need to order to re fit the door trim. Grateful for any advice 👍
@@richaedsnith711 Hi - not sure on this one - not had a look at a 90 yet ! See link below showing the clips you need for the door trims www.dropbox.com/s/1ci9mtr4jefojj0/90%20side%20mouldings.JPG?dl=0
Another neat job Simon...and a big improvement as well. I also like the black relief DEFENDER insert...they should sell well!! Well done again! 😀😀😀😀Richard
With drilling a small hole in the bumper would this work for an L405... A remote switch in between the cable and light then you can have the extra light if you want...
If you could do a double light - orange and clear - connected to indicators and reversing camera it would also solve the right indicators/hazards being obscured when the tailgate is open. Or orange right, clear left.
Excellent, easy mod. Well done guys. Change the link to this video on your web site's item page, right now it's linking to the interior lights fitting. When will these become available for sale? Black screws would be nice, but I guess it would be easy to apply a dab of paint to the heads once they are fitted.
Yes thanks for the heads up - got the video link corrected and got them on the website - for sale. I reduced the price a bit too ! www.powerfuluk.com/vehicles/land-rover/defender/new-defender-2020/land-rover-defender-2020-reverse-light-upgrade-kit.html
Bit of a problem, the clip for the electrical point won't come apart. It's almost as if it is glued together. Pushed the clip in as the video states, pulled, wiggled and tugged and nothing. Got some added leverage with a tool and to no avail, My husband even gave it a go and he said "there is no way was that was coming apart". Now off to the shop to have it looked at. It is either glued together or corroded, there is white "gunk" all around the electrical fitting, any idea what it could be. My girl is always garaged, I was very excited to try this project myself yesterday but sadly had to put my girl back together without any new parts fitted. And wasted 2 white clips to boot. 😔
Sorry to hear you could not get the clips apart - it is interesting that it has some white stuff around the connector - this could be grease ? did you take a picture you could post ? Contact customer service and we will send you some more clips free - Simon @ Powerful
Hi Simon When are these Reverse Lights and the New Design Rear Bumper Protector Coming? Are the Boot Interior Lights the same as the door welcome lights? Just looking for 2 BRIGHT boot lights. Also on the reverse lights - if you are struggling to get the lights - have a look at Denali Dual Mount Flush Back Up Lights... maybe you could do a kit with them? They are more expensive - but look it too. Question on the fitting of theses reverse lights - why did you need to remove the plastic under the light - where you mount these? is there not enough room to get the connector out with it still there? Many Thanks - Your Defender still in with issues on the locks? Keep up the good work...
Hi Simon - we are getting the lights back in stock soon and we are redesigning the mount as well. We took the plastic under the light to access the connector without removing the light. The Defender is still in the dealership waiting for its key coding / new activity key etc.
@Charles Taylor Looking at getting these in silver and black ( anodised ) finish - just need to work on the water proofing and fixings to go into the holes.
Looking forward to these coming back in stock. Whilst I’m thinking about lighting, can I pick your brain? What’s the best way to intercept a front main beam headlight signal?
Good question - I guess you want to drive some auxillary lighting ? A Violet and orange wire on RH headlight - pin 10 seems to be the best way according to wiring diagrams,,, this comes from the body control module - pin 20 There does not seem to a fuse that is driven by the high beam
@@L663 Yes, I’m looking at some front LED lighting and couldn’t figure out the best way to pick up a main beam signal without resorting to the CAN bus. Thanks for the tip, I’ll give it a go!
It seems to me you only need to remove the checker plate pieces and not the bottom pieces unless you are going to paint them. Did I miss something? I received these from you yesterday and will be installing this afternoon.
@@L663 I took them off after all, it was quite easy. All is good but I did crack or bend the permanent tabs on the checker plates as I took them off, but I got them all slotted back in. It looks like the same thing happened to yours. I also had a shop install the recovery hooks I got from you this morning. All went well and they look great. Earlier I had ordered the blue door lights and the upgraded gas and brake pedals - everything looks and works great. What’s next? 🤪
powerfulukltd that’s a pain on a new car, but sure hopefully you are all heathy, great videos and love the banter with your lads👍stay safe and keep them coming
You are correct of course... add in the clips... 4 connectors.. and the wiring ... and the laser cut parts and it add up ... We have made the kit so it is no cut and no need to touch the wiring loom.. but this all costs money.
We have these for sale on the website now ! www.powerfuluk.com/vehicles/land-rover/defender/new-defender-2020/land-rover-defender-2020-reverse-light-upgrade-kit.html
Sorry to be a nit-picker but the Road Vehicle Lighting Regulations 1989 Schedule 14 Reg. 20 states that you can have a maximum of two reversing lights. They also must carry an approval mark (CE or similar). Probably nobody cares but it could fail an MOT.
@@L663 I live far from Dubai, when I drive for more than an hour, it clicks when turning, as if there is resistance preventing traction, but when I turn off the engine, the fault goes and the car returns to its normal state.
@@L663 I went to all our industrial workshops, but it seems that they have not reached a solution to the problem, and also they deal with Land Rover like Toyota, despite the big difference between them.
Excellent work..except of the screw color. Black screws would be improve the overall impression of the vehicle.
Just fitted them yesterday what a difference they make absolutely amazing what a difference when reversing last night. Thanks Simon and the team brilliant idea cheers Carl
Most modern cars are the same regarding the reverse light output, they're terrible.
All they seem to do is show a white light at the rear so other road users can tell you are reversing.
Nice video and nice kit too, well done.
You should offer smoked lights to match the car and make em look more OEM👌🏻
Nice design!
Cool idea!
Just fitted these, the video instructions are great, thank you. I did find a surprise electrical connection when removing the passenger rear light cover, it has what looks to be an antenna stuck to the back of it with a small coaxial cable clipped to the back of the trim also. It didn’t hinder the fitting but it occurred to me that it would be awkward to upgrade these trims to the chequer plate versions you have. I wonder if the antenna is the wireless phone booster that was fitted on my 2022 110 HSE Commercial 300D. I have images if you need them, thanks again
Hi 🙋♂️ much better than the factory fitted specially good in off road dark area where is no light 💡 but I think it’s nice if they come with black glass instead white and matching with the rear lights. Even this is nice 👍 too. Good upgrade.
Thanks 🙏
Fitted this kit this morning. Easy job, just wish my fingers were a bit thinner ! Thanks for the idea and materials. Great result. Regards Non Stick Nick
Well done Nick - you just need to test it out tonight !
LOVE the product and appreciated Simon & Tyler's video. Here's some pointers from my experience. I have a 2022 MY 110 in the US. Dynamic-HSE. There was an aerial in the left quarter panel. It easily unclipped at the purple bottom connector. Take it to a bench and pry apart the bracket it's on. It's only 2-sided tape. Be careful. Remove residue and apply new 3M tape to the new quarter panel if doing at same time. If not, just disconnect if keeping same quarter panel. Tips from my install. 1) I used heat shrink connectors. 2) For the quarter panel to re-attach, those fat connectors REALLY have to be out of the way. It's a tightish fit, but it eventually works. 3) The black backing (the one with the double sided tape) did not work for me if I put it in before the quarter panel. REALLY jam it to the in-board side, but still not enough room. I added it after. More of a fiddling, we'll see if it stays secured. 4) I don't think it was clear (to me!) but you need to return the two part trim. I saved the back, but painted the bottom. I thought the new backing would screw onto it. Unfortunately, without the old backing there was nothing to screw onto. I double side taped it. We'll see how long before I have to sacrifice that back trim! In use it is a GREAT upgrade. Highly recommend getting this product. Keep bringing New Defender upgrades, PowerfulUk!!
Hi - Are you in the US - I think the extra antenna is on USA models. We have some new molded mounts coming out soon - I am sure we can upgrade you to these if your current ones have problems. Thanks for the tips.
Just installed mine. Very happy. How did you know I would need exactly 4 replacement clips 😂😂
Psychic powers !
I would recommend that you use heat shrink over the connectors to seal them against water ingress also I would do the same with the unused wiring in the harness
There were my thoughts but then I have to ask, are the loom plugs/connectors sealed where the wires enter?
Simon, just received a kit and the LEDs included have three leads so you have both white and amber colors available. I’m thinking that I might wire the amber to either the turn signals or the rear fog lights. What do you think of this idea?
This is a great little up grade.
I did have a issue with the stainless steel screws, I found them a touch too long. They pushed the assembly away from the main panel when tightening up.
Cut a couple of mm off the end and was good to go.
Hi - thanks for the feedback we will take a look at this.
Crazy that the standard reverse lights are not enough to see with the cars own reverse camera system !
I've ordered the wide wheel arch for the new 90, according to landrover fitting instructions I need to remove the lower door trim to fit arches. l was just wondering if it's really necessary, and if so which replacement clips will I need to order to re fit the door trim.
Grateful for any advice 👍
@@richaedsnith711 Hi - not sure on this one - not had a look at a 90 yet !
See link below showing the clips you need for the door trims
www.dropbox.com/s/1ci9mtr4jefojj0/90%20side%20mouldings.JPG?dl=0
@@L663 thanks very much, appreciate your time.👍
Another neat job Simon...and a big improvement as well. I also like the black relief DEFENDER insert...they should sell well!! Well done again! 😀😀😀😀Richard
Hi Richard - sold 5 sets of the black relief inserts over night !
You can get a waterproof crimp connector of the same type which would a better option for corrosion protection
good idea !
With drilling a small hole in the bumper would this work for an L405... A remote switch in between the cable and light then you can have the extra light if you want...
Looking very professional!
For a moment i though you meant i looked professional... but i hope you are referring to the reverse lights !
If you could do a double light - orange and clear - connected to indicators and reversing camera it would also solve the right indicators/hazards being obscured when the tailgate is open. Or orange right, clear left.
Yes i am going to work with the manufacturer for this design.. with a smoked lens ! That will be the sweet spot !
Just checked with Land Rover reference if this upgrade would affect my warranty. Unfortunately they say it would invalidate the whole warranty!
When will this kit be available again?
Mr Landrover man. If you go in water which is at say 80cm and you need to revise will those connections short circuit
I cant see this being a problem as water is not that conductive and also i dont think i will be reversing in water that deep !
@@L663 keep Landrover calm and smiling
Do you think changing the plugs on the loom, this kit could then be used on a L405 to fit these under the lower tailgate.
If you add a slot towards the top to the hole in the backing plate you run no risk of forgetting to pass the wire through the hole befor soldering....
Sure wish you linked the video to the panel removal. Can’t find it anywhere.
Which panel removal ?
The body panel with the brake lights which is super difficult to remove gracefully.
I like the add in loom could you do them for the D4? As I want to add a set of roof level auxiliary lights.
Excellent, easy mod. Well done guys. Change the link to this video on your web site's item page, right now it's linking to the interior lights fitting. When will these become available for sale? Black screws would be nice, but I guess it would be easy to apply a dab of paint to the heads once they are fitted.
Yes thanks for the heads up - got the video link corrected and got them on the website - for sale.
I reduced the price a bit too !
www.powerfuluk.com/vehicles/land-rover/defender/new-defender-2020/land-rover-defender-2020-reverse-light-upgrade-kit.html
Bit of a problem, the clip for the electrical point won't come apart. It's almost as if it is glued together. Pushed the clip in as the video states, pulled, wiggled and tugged and nothing. Got some added leverage with a tool and to no avail, My husband even gave it a go and he said "there is no way was that was coming apart". Now off to the shop to have it looked at. It is either glued together or corroded, there is white "gunk" all around the electrical fitting, any idea what it could be. My girl is always garaged, I was very excited to try this project myself yesterday but sadly had to put my girl back together without any new parts fitted. And wasted 2 white clips to boot. 😔
Sorry to hear you could not get the clips apart - it is interesting that it has some white stuff around the connector - this could be grease ? did you take a picture you could post ? Contact customer service and we will send you some more clips free - Simon @ Powerful
1st, the torch has a magnet on the bottom, it would have sat higher if you had used the magnet to stick to to towing eye.
Indeed the light does possess the power of magnetism !
Hi Simon
When are these Reverse Lights and the New Design Rear Bumper Protector Coming?
Are the Boot Interior Lights the same as the door welcome lights?
Just looking for 2 BRIGHT boot lights.
Also on the reverse lights - if you are struggling to get the lights - have a look at Denali Dual Mount Flush Back Up Lights... maybe you could do a kit with them?
They are more expensive - but look it too.
Question on the fitting of theses reverse lights - why did you need to remove the plastic under the light - where you mount these? is there not enough room to get the connector out with it still there?
Many Thanks - Your Defender still in with issues on the locks?
Keep up the good work...
Hi Simon - we are getting the lights back in stock soon and we are redesigning the mount as well.
We took the plastic under the light to access the connector without removing the light.
The Defender is still in the dealership waiting for its key coding / new activity key etc.
really nicely done
Would be better with black screws instead of silver ones.
beat me to it! lol
Agreed but i went for stainless so they wont rust !
Spot of gloss black paint on the screw head after assembling the light would solve that
I noticed the L-track on the side of the defender, are you going to do a video on that, fitting and their use?
Its a work in progress...just developing it.... was hoping it would catch someone's eye !
@Charles Taylor Looking at getting these in silver and black ( anodised ) finish - just need to work on the water proofing and fixings to go into the holes.
Good result
Hi, when will you have this kit back in stock? Thank you.
Looking forward to these coming back in stock.
Whilst I’m thinking about lighting, can I pick your brain? What’s the best way to intercept a front main beam headlight signal?
Good question - I guess you want to drive some auxillary lighting ?
A Violet and orange wire on RH headlight - pin 10 seems to be the best way according to wiring diagrams,,, this comes from the body control module - pin 20
There does not seem to a fuse that is driven by the high beam
@@L663 Yes, I’m looking at some front LED lighting and couldn’t figure out the best way to pick up a main beam signal without resorting to the CAN bus.
Thanks for the tip, I’ll give it a go!
Sounds so much better than the sewing machine diesel I have ☹️
Yes so far i am happy with the 2L petrol !
It seems to me you only need to remove the checker plate pieces and not the bottom pieces unless you are going to paint them. Did I miss something?
I received these from you yesterday and will be installing this afternoon.
Hi - you may be correct but it may be a bit tight - let us know how you get on !
@@L663 I took them off after all, it was quite easy. All is good but I did crack or bend the permanent tabs on the checker plates as I took them off, but I got them all slotted back in. It looks like the same thing happened to yours.
I also had a shop install the recovery hooks I got from you this morning. All went well and they look great.
Earlier I had ordered the blue door lights and the upgraded gas and brake pedals - everything looks and works great.
What’s next? 🤪
@@KY4M The checker plate parts are made from PP ( Polypropylene ) and seem softer than the original ABS painted parts. Glad its all in and working !
Illuminating guys😉, great video, quick question have you managed to get your passenger door fixed?
Hi not yet - got a quote and the insurance company are reviewing it.
powerfulukltd that’s a pain on a new car, but sure hopefully you are all heathy, great videos and love the banter with your lads👍stay safe and keep them coming
@@L663 OK - how much? it *did* look like an expensive repair.
@@johnwillett4086 £3300 +vat is the quote
I love your work... BUT..those LEDs are available on eBay for less than £10 a pair. You can set them flashing too if that’s your bag
You are correct of course... add in the clips... 4 connectors.. and the wiring ... and the laser cut parts and it add up ... We have made the kit so it is no cut and no need to touch the wiring loom.. but this all costs money.
Simon. Great idea. Would this invalidate the warranty ?
There is not cutting of the loom so i cannot see any reason for concern
On AliExpess the price is from 0.75 to 2.48 $ for 1 piece, depending on the country.
Thanks for sharing ! but we are confident our product is a complete solution.
I think what it came with is fine
With over 1000 sold i think other people do not agree !
Or you fold the excess cables ends and tape them up. This will leave you more cable if you ever need it.
good idea !
We have these for sale on the website now !
www.powerfuluk.com/vehicles/land-rover/defender/new-defender-2020/land-rover-defender-2020-reverse-light-upgrade-kit.html
Sorry to be a nit-picker but the Road Vehicle Lighting Regulations 1989 Schedule 14 Reg. 20 states that you can have a maximum of two reversing lights. They also must carry an approval mark (CE or similar). Probably nobody cares but it could fail an MOT.
Bit of tape over the old ones for MOT ? I believe the lamps are CE marked. We like nit pickers ! its you guys that keep us all clean and nit free !
Cracking mode... black screws would be good
Yes agree - i went for stainless for peace of mind !
Rear drivers side wheel arch bit isn't on properly, follow your helper to the north 🧭
But no one spotted the new aluminium side rail below the window.... come on Greg... loosing your touch ?
Nice!
Thanks Alan !
have it on good authority that area was supposed to be a hop up to roof but was too shallow!
Hi - it does seem to lack purpose !
Restock plz !!!
We have new stock and an improved support coming !
Brother, thank you for the information. I have a 2009 Range Rover Sport that has a problem that no one knows to fix. Can I contact you via WhatsApp?
I doubt i can fix but please share your problem ? where are you ? I have friends in Dubai ?
@@L663
I live far from Dubai, when I drive for more than an hour, it clicks when turning, as if there is resistance preventing traction, but when I turn off the engine, the fault goes and the car returns to its normal state.
@@L663
I went to all our industrial workshops, but it seems that they have not reached a solution to the problem, and also they deal with Land Rover like Toyota, despite the big difference between them.
Doesn’t look good. Factory looks best to me
But the factory ones are not bright enough !