Great video. I am a dog groomer with some Andis clippers. I came across this video while researching maintenance, and now it's saved for the future. Thanks.
Hi…very informative and thorough, thanks. I have a hard time moving the switch up and down, the outside grey with red lock button. Like that when bought new. 🤷♀️
question. I rarely use my agc2 clippers. but now that I'm using them, they cut well for about 30 seconds, then suddenly the clippers seem to jam up, stop cutting, and the engine hums a little louder. At this point I flip the trimmers over and brush my dogs hair with them while on for 20 seconds, then magically the engine hum disappears and they work again for another 30 seconds. what's my problems?
Isaac Mooneyham I can not diagnose with looking at it sorry. But sounds like it was dropped and something broke and seized the armature. you'll need to take it apart and find out what seized it up.
Not sure what it's called but that plate that you take off for the blade drive, mine keeps popping off and I keep it clean and it still seems to not want to stay snapped in.
Hello, I have an AGC that I purchased last year, but started using recently. Only used them twice and then they started pulling through hair. I bought new blades and I’m getting the same issue. I took them apart and cleaned them and I’m not sure what went wrong. Both blades seem to be moving fine
Lindsay Surmeier hello. Most of my customers buy new blades and have me sharpen them right out of the package but if you do not want to pay for sharpening there's a warranty on the back of the box. If the blade is moving and pulling hair the blade is probably dull. You might have the wrong size of blade for that type of hair, also. I give free estimates after I look at them. Have a nice day and thanks for watching.
Question from Ireland Cam bearing isn't working as it should,without blade on I sometimes have to push the plastic drive bearing to get it started,when I but the blade on it doesn't move at all but I can hear it working...any ideas
sounds like you need a cam assembly bc it is probably striped from the aremature or the aremature is bad and has a dead spot on the communtators of the motor.
Hello Nick, after watching a bunch of your videos (and subscribing) I picked up an Andis AGC 2 speed off Ebay. Can you recommend an online store to buy spare parts, clipper oil, etc? Keep up the good work! Thanks
Yes the aremature is bad bc it either was never serviced or oil got down into it. The switch and aremature will need to be replaced bc it blew the switch fuse also
I hope you have an easy explanation for me. I replaced the terminal board on my 2 speed ultra edge due to a blown resistor. I put the new board in and it also blew a resistor. Any ideas. Thanks. TB 22681 rev A
"sorry for your loss" Funny. Thought I'd give it a shot anyways. I'm a capable DIY'fer. Thanks for the info. I will be watching more vids on how to care for the clippers. Your videos are easy to watch. To the point. No blah blah and the background music is not too loud and annoying. If you guys sell refurbished clippers let me know.
Diesel Bourbon NP. glad you enjoy the videos. I have some available refurbs but for pre existing customers or if you have clipper blades sharpened or scissors. thanks for watching.
Great video. I am a dog groomer with some Andis clippers. I came across this video while researching maintenance, and now it's saved for the future. Thanks.
Np. Thank you for watching
Hi…very informative and thorough, thanks.
I have a hard time moving the switch up and down, the outside grey with red lock button. Like that when bought new. 🤷♀️
Thanks for watching. If you ever need a major repair, send it in and we'll fix the switch on the case.
question. I rarely use my agc2 clippers. but now that I'm using them, they cut well for about 30 seconds, then suddenly the clippers seem to jam up, stop cutting, and the engine hums a little louder. At this point I flip the trimmers over and brush my dogs hair with them while on for 20 seconds, then magically the engine hum disappears and they work again for another 30 seconds. what's my problems?
Isaac Mooneyham I can not diagnose with looking at it sorry. But sounds like it was dropped and something broke and seized the armature. you'll need to take it apart and find out what seized it up.
Not sure what it's called but that plate that you take off for the blade drive, mine keeps popping off and I keep it clean and it still seems to not want to stay snapped in.
The plate under the hinge? Because there is no plate Under the Blade Drive
Hello,
I have an AGC that I purchased last year, but started using recently. Only used them twice and then they started pulling through hair. I bought new blades and I’m getting the same issue. I took them apart and cleaned them and I’m not sure what went wrong. Both blades seem to be moving fine
Lindsay Surmeier hello.
Most of my customers buy new blades and have me sharpen them right out of the package but if you do not want to pay for sharpening there's a warranty on the back of the box. If the blade is moving and pulling hair the blade is probably dull. You might have the wrong size of blade for that type of hair, also. I give free estimates after I look at them. Have a nice day and thanks for watching.
My and is Clippers just barely cut and even worse when I have a guard on them. What's the problem?
It could be a variety of issues. Not always easy to tell without inspecting them.
Hi Nick. Thank you for your videos. Where can I find electronic cleaner like the one you have?
its only sold in 5 gallon can to distributors. they sell little cans at walmart. look for electronical none conducting cleaner
Question from Ireland Cam bearing isn't working as it should,without blade on I sometimes have to push the plastic drive bearing to get it started,when I but the blade on it doesn't move at all but I can hear it working...any ideas
sounds like you need a cam assembly bc it is probably striped from the aremature or the aremature is bad and has a dead spot on the communtators of the motor.
Just purchased ACG ultra Edge. IS THERE SUPPOSED TO BE A SPRING UNDER THE HINGE ASSEMBLY?
JEFF BROWDER no it has a latch not a pressure hinge.
Thank you so much for the quick response!
Where do you get the red lube that you put on the thing by the blade drive?
Oster gear lube www.theedgepro.com/
Hello Nick, after watching a bunch of your videos (and subscribing) I picked up an Andis AGC 2 speed off Ebay. Can you recommend an online store to buy spare parts, clipper oil, etc? Keep up the good work! Thanks
RobertL hello. Np. I buy my parts from Fort worth shaver and appliance. Thanks for watching
If my clippers smelled like something was burning and then it stopped working it my motor burned up?
Yes the aremature is bad bc it either was never serviced or oil got down into it. The switch and aremature will need to be replaced bc it blew the switch fuse also
Hola. Desde Argentina. Una pregunta: Es posible reemplazar los rodamientos de motor?
Hola. Solo el cojinete de leva es reemplazable en la armadura.
I hope you have an easy explanation for me. I replaced the terminal board on my 2 speed ultra edge due to a blown resistor. I put the new board in and it also blew a resistor. Any ideas. Thanks.
TB 22681 rev A
Diesel Bourbon armature is bad or wet but if wet its usually bad
WOW that was fast. Replace the armature and get another board. About a $75 fix for me. What could you guys do it for?
Diesel Bourbon I can't beat that. sorry for your loss.
"sorry for your loss"
Funny. Thought I'd give it a shot anyways. I'm a capable DIY'fer. Thanks for the info. I will be watching more vids on how to care for the clippers. Your videos are easy to watch. To the point. No blah blah and the background music is not too loud and annoying.
If you guys sell refurbished clippers let me know.
Diesel Bourbon NP. glad you enjoy the videos. I have some available refurbs but for pre existing customers or if you have clipper blades sharpened or scissors. thanks for watching.
if my copper wire from the motor has come out of it's slot is this fixable. Thanks
Kirsty Russell all parts are available.
where at at what part would I be looking for
Kirsty Russell google search Andis distributor. I do not know what piece you need. I can't fix it without me diagnosing it.
donde puedo encontrar una pieza q necesito para la andis agc 2 vel.la pieza es la q muve la leva se le barrio la cuerda y no aprieta soy de tabasco
Trate de Fort máquina de afeitar y el aparato
www.clipperoutlet.com/
Julio Hidalgo quiero comprar
me interesa la azul cuánto cuesta deme el precio xfa
My clipper speed runs good until I start to cut the dog. Then it slows down.
It can either be a blade problem or an armature or brushes. Maybe your blade needs oil.