Great, but way too big for my TL072 op amp! Thank you for covering this as I've just started working with op amps. You have perfect timing. Have a great day and have a coffee for yourself!
Dear Sir, Your explanation about dual power supply is very helpful to me. I need one more answer. Could you please explain how to include digital volt and ampere meter in that power supply? model number: DC 100v, 10A (48 x 29 x 21mm)
Hi Haseeb, Will it still possible to combine 23.2v and 24v using this method. Both of them with 16ampacity each. SMPS output is fixed and non-adjustable, same manufacturer and brand. Been planning to combine their amps prior to my upcoming project. Thanks.
Great Video! Quick Question - So with this, I can have: -12V, 0, +12V and 24V by connecting +ve to positive and -ve to negative correct? In this scenario GNF will be floating thru the jumper Connection, no need to connect?
I think with this combination we can only use resistive load for negative voltage(I think so, correct me if I am wrong). Because if we connect an equipment with polarity(positive and negative), the equipment may not Power on or it may damage or cause damage to SMPS(negative voltage). Please correct me if I am wrong. Thanks in advance. Great day...
superb this configuration is similar to differential power supply. when we need a + /- power supply, especially when we use to test differential circuits (like opamps, comparators, digital to analog converters, analog to digital converters) for normal use, it can be used same a series connected power supply configuration =, just -ve will be used as common
@@HaseebElectronics The negative output (-) is the return point (GND) for the secondary side of the power supply. If both the PS are the same and if the positive terminal from one of the supply is connected with the other, the connecting wire between them will act like a pure resistor of very low value which will start to draw all the currents from the first PSU to the second. Let's say we'll use 10 AWG wire for the ground and let the current pass to make it a common ground for the dual supply. In a way, this common ground will be very noisy making it unusable for it will inject this noise directly to the load. Please explain if this is not the case.
Sir I need your help if I have 2 12 volt 60amp power supplies with 3 position & 3 negative terminals of each amps how to connect in parallel sir and I want 12 v 120 amp power please do a video about this sir please 🙏🙏🙏🙏🙏🙏
आपके बहुमूल्य शब्दों के लिए बहुत बहुत धन्यवाद। आपको मेरा उर्दू चैनल "HASEEB ELECTRONICS URDU" अवश्य देखना चाहिए। उस चैनल पर मैं उर्दू भाषा में वीडियो साझा कर रहा हूँ। यह विशेष रूप से मेरे भारतीय और पाकिस्तानी भाइयों के लिए है।
Good job keep it up 👍🤗
thanks a lot
Great, but way too big for my TL072 op amp! Thank you for covering this as I've just started working with op amps. You have perfect timing. Have a great day and have a coffee for yourself!
Like excellent informative vedio dual supply connection tutorial great work best wishes good morning 🌅🌻🌹
thanks a lot
JazakallahuKhir..👍👍
Excellent job keep sharing
thanks a lot
Здравствуйте благодарю вас за прекрасный ролик мне очень понравилась желаю вам удачи вашем деле друг!👍
особая благодарность и наилучшие пожелания
Dear Sir, Your explanation about dual power supply is very helpful to me. I need one more answer. Could you please explain how to include digital volt and ampere meter in that power supply? model number: DC 100v, 10A (48 x 29 x 21mm)
it's never too late to learn!! :D
Thanks for this!
now, I have a question..... is it possible to use separate AC inputs for each PSU.....??
nice sharing and good information
thanks a lot bhai
Non smetterò ha guardare le tue interessanti video. Grazie 👍
Buon giorno. grazie speciali e auguri caro fratello
Very Very nice sir
Hi Haseeb,
Will it still possible to combine 23.2v and 24v using this method. Both of them with 16ampacity each.
SMPS output is fixed and non-adjustable, same manufacturer and brand.
Been planning to combine their amps prior to my upcoming project. Thanks.
Haseeb bhai Namaskaar 🙏
Namaskar bhai
What would be the best way to add a on off switch for this
Thank you very much sir 🙏 🙏 🙏
Most welcome
Beautiful information
thanks a lot
Good sharing
Lk 61 brother 👍👍👍
Many many thanks
Thank you sir, for 5v 50A power supply which diod should use...
Great Video! Quick Question - So with this, I can have: -12V, 0, +12V and 24V by connecting +ve to positive and -ve to negative correct? In this scenario GNF will be floating thru the jumper Connection, no need to connect?
I think with this combination we can only use resistive load for negative voltage(I think so, correct me if I am wrong). Because if we connect an equipment with polarity(positive and negative), the equipment may not Power on or it may damage or cause damage to SMPS(negative voltage).
Please correct me if I am wrong.
Thanks in advance.
Great day...
superb
this configuration is similar to differential power supply.
when we need a + /- power supply, especially when we use to test differential circuits (like opamps, comparators, digital to analog converters, analog to digital converters)
for normal use, it can be used same a series connected power supply configuration =, just -ve will be used as common
@@HaseebElectronics The negative output (-) is the return point (GND) for the secondary side of the power supply. If both the PS are the same and if the positive terminal from one of the supply is connected with the other, the connecting wire between them will act like a pure resistor of very low value which will start to draw all the currents from the first PSU to the second. Let's say we'll use 10 AWG wire for the ground and let the current pass to make it a common ground for the dual supply. In a way, this common ground will be very noisy making it unusable for it will inject this noise directly to the load.
Please explain if this is not the case.
Great stuff.......thank you!
best regards
Can we do it with single SMPS as there are two output for each + and -
yes
if have + / - power supply, and it have common line as zero volt return.
then it is already dual power supply,
do i use dual power supply for electric door lock
you can use a relay to revese the connections
and you will use only one power supply
Can i use this for.. Sound amplifier??
wow really great man
best regards
Very good very good very brother
Thank you so much 😀
could i do the same with computer power supplies?
yes we can do it
I can’t seem to get them to work. I’ve tried diods in both directions. Just using two cps units. Not ATX units. Can you send me in the right direction
Thanks and my question is ,where does negative voltage work..my thinking is that only +12v is productive
👍👋👋
thanks a lot dear friend
Can i use this connection for my home theatre
Super
can i substitute pc2561 with pc2581. sir?
yes brother you can replace it
@@HaseebElectronics thanks u sir
It works only if the main supply and the output lines are loosely coupled.
wooow....
how to join 2 psu 12 5 amper to 24 volt 5 amper. coz i need for ampli TPA 3116d2. please help me Sir..
Sir I need your help if I have 2 12 volt 60amp power supplies with 3 position & 3 negative terminals of each amps how to connect in parallel sir and I want 12 v 120 amp power please do a video about this sir please 🙏🙏🙏🙏🙏🙏
Watch his 597th video bro, you need a schottky diode, its easy you can do it
What if I have one smps
Great video ---thank you. I gather that there is no connection between power supply ground and negative output.
You are correct. as the ground is taken from +ve terminal
Hey What's up ✌️
welcome dear
समझ मे आ गया भाऊ लेकिन यही आप हिंदी मे explain करते तो बहुत लोग समझ पाते😢
आपके बहुमूल्य शब्दों के लिए बहुत बहुत धन्यवाद। आपको मेरा उर्दू चैनल "HASEEB ELECTRONICS URDU" अवश्य देखना चाहिए। उस चैनल पर मैं उर्दू भाषा में वीडियो साझा कर रहा हूँ। यह विशेष रूप से मेरे भारतीय और पाकिस्तानी भाइयों के लिए है।
Come first still wt 📌
thanks a lot
Kayse up mare vi
Ji bhai Aah ka shukr he