LED Turn Signal Resistor Kit Installation
Вставка
- Опубліковано 4 сер 2016
- Freddy shows you how to install a LED Turn Signal Resistor Kit on your 2016-2020 F-150.
Purchase Product Here:
www.cjponyparts.com/led-turn-...
Eliminate that terribly annoying hyper blinking by installing this LED turn signal resistor kit. Accompanying this kit is two resistors and four scotch-lock connectors. Featuring eight inch leads, an easy two hour installation and a resistance rating of 60ohm, 50w. Fitting most vehicles, this LED turn signal resistor kit is a high-end solution to your pesky hyper blinking problem.
Check out more F-150 parts from CJ's here:
www.cjponyparts.com/ford-f150-...
Subscribe to CJ Pony Parts on UA-cam here:
ua-cam.com/users/subscription_c... - Авто та транспорт
Hey guys, (CJPony Parts) great video, however, the wires you are tapping into are not completely correct. The ground is, however the blue with grey tracer is actually the park light circuit. The correct wire for the turn on that side is green wire with orange tracer. Hope this helps anyone doing this install. Be sure to mount these resistors to bare metal....
Don't want to melt the factory wiring.... so lets mount it with sticky tape that will melt. Brilliant idea!
That double sided tape is gonna melt lol
Jumped to the comments to see if anyone mentioned this and if there was a rebuttal... first comment... no response. Prolly a bad idea.
🤣🤣🤣🤣🤣👌🏻😎
Surely you read the part about how the resistors get really really hot , so good luck with the double sided tape. They put screw holes for a reason.
Fantastic video, thanks for putting it together! All the other videos on youtube gloss over the actual work, and show everything already done. Your camera angles are fantastic, I can clearly see what to do. Great background music too!
Thanks for the tutorial. For the rear resistors (might have been useful to mention they're 6 ohm), it is better IMO, to install them on a metallic surface with at least one of the two screw holes, not with double sided tape. And to close the video, it would have been nice - as someone else has already mentioned - to show the LED lights working sans hyper flashing.
very useful guides. thanks
Thanks for watching, glad we could help!
Thanks for the music I was rocking out
What about changing the flasher ,instead of putting load resistors on cheap scotch locks
It would have been nice to see the views of the blinkers working after the install.
Rock44260 you did see a lil the mirror turn signal was flashing normal speeds but yeah would of been nice to see the whole rear and front
Thanks for the video. However, to reiterate what others have mentioned, it is much better to secure the resistor body by screwing it metal-to-metal (for greater heat dissipation) than using two-sided tape shown at 3:43, even better if both ears are screwed to a metal surface.
I mount the load resistors in the metal of the truck with Resistors Plug n Play
Can you do a demonstration on a 2017 Silverado??
My passenger side has yellow w/brown(outside) blue (middle) black w/yellow (outside).... what 2 do I connect the resistor
I checked all the wires & installed the resistor. I made sure the brake light, tail light & turn signal worked...and it did (all in the same bulb). Then I installed the LED bulb. Only the brake light & turn signal worked. I flipped the bulb around and the only the parking light would work. Hmmm? Any ideas/suggestion? Thanks!
i have a 2015 f150 and followed this, the interior light on the cluster hyper flashes still but the lights dont?? any help
the rear blinkers has 3 wire I know one is ground the other blinker and brake when I tested it with my test light 2 of the wires both blinked does it matter what one I use from the 2 as the positive?
man those resistors really needed to be mounted to something metal as they get very hot and will easily melt through any plastic parts I modified mine to get more length on those resistor wires and used self tapping screws to mount them to the back side of the crash bar well away from plastic parts
Marvelle Washington THIS^ Thank you!
The resistance heats up, because you fix it with that glue, could it melt it? Another query, the resistance goes in the section of the lighthouse where water can fall behind, something will happen with the resistance if it drops water or is water resistant?
I’ve tried with the resistor but still have hyper flashing did what he did so could it be the bulb itself?
Can I use this for with my 2018 mustang fog light removed so it doesn’t hyperflash ?
question I replaced front and rear blinkers and brake lights on my 2011 FORD Escape with new LED's and I added LED Decoder Adapter Anti Hyper Blink Flash Error Cancel Canbus Brake 12V, just the back light, turned the blinkers one it was blinking normal, but as soon as I turned the lights on it started blinking fast again, any ideas how I can fix this
HELPPPP!!!! CHEVY MALIBU 2017 - I bought 7443 Switchback lights I plugged the LED lights in but now my car is saying check front and left turn signals. It is giving me rapid flashback feed in which I need resistors plugged up to it. I have the resistors but what cords do I need to connect it too in my car? There are 4 colors fro my switchback which are PURPLE, BLUE & WITE and 2 BLACK CORDS. How do I know which 2 cords I need to connect the resistors too?
Thanks,
Victor
Use self tapping screws to mount. The equalizer is a heat sink and will get very hot. Do Not use tape, it will melt.
How can I stop my brake lights from over riding my turn signal ?
This was very helpful, and the close-up the video was excellent. However, I do wish I could watch and listen without the same old 'monkey-see-monkey-do' rock music. It just seems out of place when all you're doing is taking apart a head light.
If you only do this with the rear(replacing with LED's and adding resistor) Can you have regular incandescent bulbs in the front or do you need to do leds on all signal lights?
in all LED bulbs
Will they prevent parasitic draw from leds?
Cant you just go in with forscan and change the setting
So it also has no error on canbus cars?
Does the double sided tape need to be anything special to deal with the heat
im having the same problem on my 95 tahoe since its an older truck if i did the same and put in resistors would it work? i just put in all new led lights
Probably yes.
Do you need these for a mustang 2009
good
Are you sure about the color code, I did it just as you did and got no results . The dash lights are still flashing like crazy? Thanks
Perfect instruction, but the music was too overbearing.
I did the same but mine didn't work. I am sure the wiring I made has no mistake. When I first start the car, there is error code and when I blink the signals, the first 3 blink is fast (hyperflash) then it blinks normal. After using both signals, the error code is gone. Turning the engine off and starting again, the whole process repeats. How can I solve it?
Is it bad if we dont install resistors?
Btw from my earlier comment, the installer has given out the wrong color code. It is NOT the blue wire you need to tap, he has the ground correct but you need to grab the other wire. Nearly burned up my wiring.
For a 2014 Chevy Cruze... Im trying to figure out the front and rear turn signal wiring.. Which is the ground.. And the blinker wire? Front is blinker wires are brown and violet? Anybody know?
Don't know if you figured this out yet, but grab a multi-meter, set to VDC (volts dc), connect black lead to any ground (battery - terminal, chassis), turn on blinker, and probe pins of signal connector with red lead. The pin that pulses voltage is your blinker power wire.
Is it standard for Ford to use a blue wire for the power and a black with yellow striped wire for the ground? My Ford Fiesta has the same color scheme in the turn signal wires and I'm nervous about jumping into it without testing the current in each wire.
Ford is not always consistent with their wiring colors. Black with a stripe is a common ground color though.
+Bill Tumas Thanks for the reply I appreciate the info!
Why using four 50w resistors who draws a total of 200 watts to replace four 21w incandescent bulbs who are drawing 84 watts total? Should four 25w resistors for each bulb or one 50w resistor for each side (front and rear) not be sufficient? If I'm not mistaken, each side is one circuit so one resistor of 50w for each side should be enough to prevent hyperflash.
the Resistors Wattage Rating is defined as the amount of heat that a resistive element can dissipate for an indefinite period of time without degrading its performance. So up to 50 watts. Not operating at 50 watts. 6 Ohms is the resistance.
LONG PROCESSING, THANKS
Do you need resistors on a 2014 chevy ?
MORE MONEY yes
I ned HELP!!! I did exactly what you do in video, but i still getting the annoying blinking lights . I also remove ALL LED bulbs from headlights & i still getting blinking lights. This situation is stressing me any HELP will be appreciated. Ty
Ruben Martinez I'm having the same problem.
@@1wolfdaddy I feel your pain
I have 2 questions... was wondering if someone could give me hand? I need to install these resistors for my back lights: Turning signals and brake lights. Reading some of the comments, I noticed that it seems a bad idea to use double side type to hold the resistor in place. 1st question: Do they get hot? Is this normal? 2nd question: In my car, there is room to place one of this resistor, thus it is going to be very tight. Some of the original wires will be against the resistor. Does this resistors get so hot that could melt the original wires jacket/insolation? Any advise? Thank you.
Hey Bud, also trying to
Do this on my Accord.
Answer: from what I’ve seen on videos, resistors can reach up to 115-200 degrees
So try to install on metal away from any Plastics, cables, rugs etc
Good luck
I put resistors on mine they work on the outside but the inside still flashes fast can you help with this?
Feel the resistor while the light is flashing fast. If the resistor is not getting hot then it's improperly installed or its defective. It should get hot pretty quick.
@@cjponyparts okay I'll try that
Those resistors get extremely hot 400f + double-sided sticky tape is not going to hold that on. I even used quick setting automotive glue yep it came off to.
does it get hot all the time or only when the lights are on?
ALPHA GAMERS CLAN just when they are in use
ALPHA GAMERS CLAN Only When Ur Using Flashers When Lights are on or Ur Pressing on Brake Lights There Not In Use Only When Using Ur Flashers That's When They Get Hot
Also wouldnt the double sided tape just melt off?
Nope, it holds up just fine.
Kevin Pierre I Put Mine Up With Double Sided Tape As a Buddy of Myne Did I Was Kinda Having Second Thaughts About It But Going on 4 Months & There Still On Haven't Melted Off
Who do I know which one is the ground wire?
He explained on the video
Ive heard that one can just buy the upgraded relay or flasher that is for LEDs and theres no need for resistors???
yep they are available on Amazon
Ya this is stupid and a huge waste of time and shows a big lack of knowledge. Heavy Duty Flasher Relay.. Done.. idiots
do you have a link? :)
LED Flasher Relay and yes they work your Hyper Flash will be no more, don't do this dumb shit on this video, their fucking idiots!
www.amazon.com/gp/aw/d/B0031GR7BA
Rumeel12708 yes but a lot of newer cars doesn't have a relay
Should of just shown the turn signals on after u installed them
jeeeeezus, all of that to remove the headlights. pita!
hung mammoth those damn Fords
You should see how to change a fog light or blinker on a 2013-2015 Ford Escape. 🙄🙄😒😒
Just buy them with built in resistors
Why install resistors when you can upgrade to an electronic flasher for less money and much less work.
Dude, great video but please don’t use music, verydistracting
Not black and blue
holy crap, it's almost like Ford doesn't want you to be able to replace your own front headlights, that's ridiculous.
Next time... just admit you you f*cked up instead of having a tutorial with wrong instructions... a simple disclaimer saying, "We're mechanics, not electrical experts." Would be good enough. SMH
Is the music necessary? Not everybody that works on their own car likes to head bang while doing it. Sounds like a Beavis and Butthead episode.
How about less annoying music!
Only fools use scotch locks