First start Willys L-134 Jeep engine rebuild

Today is the day! Time for the first start of this old Willys L134 engine! Below is the full list of parts that I used for this project. Thanks for watching!
Use code REDEYEGARAGE10 to save 10% of your entire order from www.kaiserwillys.com
Engine Overhaul kit:
www.kaiserwillys.com/products...
Starter:
www.kaiserwillys.com/products...
NOS Connecting rod:
www.kaiserwillys.com/products...
12V coil:
www.kaiserwillys.com/products...
Distributor:
www.kaiserwillys.com/products...
Water Pump:
www.kaiserwillys.com/products...
Thermostat:
www.kaiserwillys.com/products...
#willys

[@HitokiriRaiden]

Just goes to show how tough these old motors are. Nice to see it saved and not tossed like most would have.

[@geoffreyclark2805]

Just goes to show, you can't keep a good engine down. Called "Go Devil" for a reason, it goes like the devil. Great work Seth with alittle help from Kaiser Willy's.

[@user-rv4ob4tg9x]

I knew you knew it was going to do better than smoke and sputtering. Nice job sir!

[@redeyecafegarage7484]

Thanks 👍

[@rchuyck]

Sounds just like my '47 2A!!!!

[@creativeloafer9792]

Dang, sounds great! A lil fine tune, she’ll be ready for work!

[@redeyecafegarage7484]

Thanks! I think she has potential.

[@greywolfwalking6359]

THE SWAMP THING IS AAALLLIIVVEE!! Amazing!! Like you said, check,check..n..
fine tune and off to
another trail run!!
Thanks for sharing!
TEACH!!!!!
👍🧙‍♂️🐺🤙

[@redeyecafegarage7484]

Yup she’s back to life! Thanks for watching!

[@garagemdocadinho]

Next month I’ll bring my old cj3a from my fathers house. She is at least 13 years without running. My plan is doing my best at my garage and why not record it? Your channel is good inspiration to me.

[@redeyecafegarage7484]

Excellent!!

[@bobuncle8704]

I knew all along that you’d be successful 👍👍

[@maxvanrunkle1052]

Good job Seth!! Thanks for sharing and God bless! Max

[@redeyecafegarage7484]

Thank you! You too!

[@andykirkendall8285]

🎊 Congratulations 🎈🎉 😎😎😎😎😎

[@vintagejeep]

Looking good! 👍

[@187manowar]

Nice work!! That's impressive.

[@redeyecafegarage7484]

Thank you! Couldn’t have done it without your support and lots of good parts. 😆 😊

[@187manowar]

@@redeyecafegarage7484 HAHA. 99.9% parts and .1% positive thoughts from my end.

[@LuminousBlueVariable]

Absolutely amazing!! Good job man!! Well done!

[@redeyecafegarage7484]

Thank you!

[@amx19733]

Always Great content!!!!

[@redeyecafegarage7484]

Thank you!

[@scottpetrie8707]

Your first 1:36 was the best. Don’t polish shit! To many others edit the hell out of stuff.There are only a handful of what is good. Mustie1 is a mechanical genius and Vice Grip Garage. Genuine people.metalshaper as well

[@redeyecafegarage7484]

There’s a balance between showing everything and not publishing a 47 minute long boring video 😆 some people also need to trim the fat. No one wants to watch you fumble around looking for tools or tightening all 27 oil
Pan bolts. If it a not a step by step video I edit out the fluff. Also… eveyone will just tell you everything you do is wrong anyway ha!!