BOSH AXXIS Washer Machine Insane Brutal Spinning Sounds Like A Jet Plane
Вставка
- Опубліковано 15 жов 2024
- This is a very powerful machine. The Bosh Axxis dryer also is installed on the top. This washer sounds like a jet plane and the maximum spin is extremely powerful, able to leave the clothes almost dry. What you see is what happens when the washer is not installed correctly. If the washer is not leveled properly, this is what happens. Also remove any piece in the base which can cause some unevenness. This washer is great but must be installed properly, or it will cause an earthquake in your home, even with the softer spin cycles.
bosch washing machine bosch washing machines bosch appliances washers bosch washing machine manual bosh washer dryer washer dryer combo b0sch appliances spin dryer tumble dryers axxis bosch
lavadora lavar ropa lavadora secadora bosh axxis
video taken with iphone4s quicktime mov
1:44 someone called the cops
Even the cops got alerted :D
just love the sirens in the back after the machine went haywire and stuff falling apart .. hahaha I loled my ass off.. haha
.
LOOOL!
You are right, this is an idiotic installation. The guys of the store did not remove the transit bolts. The washer now works like a charm.
66 ujom
Who ever installed your washer shall be fired cause of this evidence
In mijn boekenkast het jaar
Well you're suppose to remove them or your washers drum would have been fucked up
the guy who installed the washer & dryer in your house need to be fired for good
and someone else who's smarter than that guy should have installed it properly
I've been looking for this video for so long
Me to When I was younger I always Watch This Video aus like 4 Years Old
This is why the transit bolts are required to be removed before the washer can be used or the Washing machine can anytime quake and interfere the machines action.
Open the door and undo the seal (held in place by a spring tensioned wire) and push the outer lip of the seal inwards into the drum. Now check the large concrete/cement counter weights attached to the outside of the drum. Put your hand inside the drum and rock it forcefully from side to side to recreate the knocking. This will locate the issue pretty quickly. Occasionally, if the washing machine has been previously over-loaded the drum counter weights can become dislodged so that they knock the inside of outer casing (left front) on spin cycle. Slacken the counter weight retaining bolts (8mm or 10mm) enough to again reposition the weight(s) to the circumference of the drum and retighten the retaining bolts until they are really tight. Rock the drum to be sure that the knocking has been cured and reinstall the front seal and spring tensioned wire retainer.
joseph prosser f
joseph prosser
joseph prosso.
joseph prosser t
Wth your wrong its transit bolts
1:02 washer spins like a jet plane.
1:25 washer dances while doing a fast spin
1:44 someone calls the police
2:02 start pause button pressed again
0:52 text labeled "2 MINUTES LATER" shakes
1:11 washer shakes around
Thanks
Someone calls police😂🤣
@@96Ss00 yep. they did lol.
It's funny how the ambulance went by after it broke
Never Leave the washer unleveled during the spin cycle other wise it will vibrate violently and cause noise
I could think differently....maybe Iam being gangstalked 😱😱🤣🤣🤣
I don't think waht happens in the "max" spin
Where the Trasit bolts? I have same situation with WAS32381, I install it by myself. Thank for your support
Idk man
Sorry
I like how the emergency services arrived as soon as the machine broke the dryer lmfao
Top new Quality Bosch generation
Do you still have the washing machine???
LOL Sounds like someone called the police
My washer is exactly like that one on the video but it won’t start the lights are blinking that’s it
Time for another "why is this in my recommended"
Next time before calling the cops, pls: make sure that transit bolts have been fully removed, secure the dryer with a proper staking kit and avoid washing single or super heavy items (e.g. xl bath towels) alone cause it would absorbs water and tend to stuck in one side of the drum leading to massive vibration during spin cycle!
im torn between these or the samsung onyx models
ha,ha,ha......precision technology from Germany!!!
Aristyides Cupido is a woman who has been a great grandmother for the first year in the world of the past three days and she has no idea how many people she has ever seen in their life and she is the only person that I really really want for a woman who has a great time to have the best understand that you are in your heart to your family and eeee you and you will be the first person you know and the person who really knows how much I hate them when I am a man who can talk with me and you just don't like you so much to say that I am the person you want but not for some one reason
AZXggbggggggg bbbbbbbane
The only problem with this app has to be that the app crashes and the app does it again it does all the time but the app does it all of I txcnnhch vh svxchfdcnddf h s dh scd do the
Ashton is the best in this year to WashingClothes
Aristyides Cupido
Aristyides Cupido
LOL 1:43 I heard cop sirens 🚨 I think they got alerted 😆
I hope now you have remove the bolts and the washer has begun to work good. :)
WHAT IS THAT THING THAT FELL FROM THE DRYER?
Nikos Podas the bottom cover
Reading seems to have become a difficult task for the people nowadays. And reading an instruction manual seemingly even more so.
H
Haha
It’s not about reading the manual. It’s about the transport bolts.
@@ericn.5263 Yes. But tell me, if you do not have any knowledge about appliances, what should you do before you start operating them? That's right - read the manual. And there, within the first few pages, it usually states that the transportation bolts have to be removed before plugging and operating the appliance. Hope that my comment is now clear enough for you.
Mine makes the same whine like a jet engine. I don't think this is the normal operating sound. If you spin it by hand, you hear the same sound - almost like a burned out bearing or motor. Also you can't just stack a dryer on top of it. You should have installed the mounting kit, which holds the dryer in place.
cause u didnt take ther dam tranist bolts off idiot
randomrazrr the motor doesnt burn cos the bolts werent removed.
replace the motor.
tolanstout
randomrazr to book now know HV
Transit bolts have to be removed then it has to be made a nivelation-to set the proper level so that the washer could not shake like this.I don't know who has installed this washer...Bosch work good, it could not be a fabric defect.
It sounds just fine to me...when I reduce the volume of my computer.
😂
I had the same issue. You can read the manual and you should see the where the 4 shipping bolts (with white plastic housing) at the back of the machine.
Dude page 12 of the manual, remove transport bolts before running machine
Mark Meleg ц
Bentleri ve bu gdsign at İzmir Anadolu
Meleg Design és divat
Meleg Design g
Ray Holden v
Wow did someone call the police because your washer was out of control! Have you took out the transport bolts at the back?
You should have -put the washer on top of the dryer.-
*Uninstalled the transit bolts.*
But if the washer was on top of the dryer it would be hard to reach the pipe work and maybe even the controls and dispenser drawer
unbalance or very load?? what is this???
transit bolts
this is the newer model 208 volts,check your wiring you must have it to 240 v. you need an electrician!!!!!There is also an 110 volt but its discontinued.
you dumb ass. Their are 4 screws in the back of the unit that is placed to prevent the drum from getting damaged during transportation. remove the screws removes the vibrations.wow
@@ernie787 I'd assume the motor actually runs on 230-250v as it seems to be running at its normal speed. If the motor were 208v and running on 240v it would be spinning faster as it would be overvolted.
The washer said to the dryer, " Bro get off of me!!!"
Where exactly where the detergent and fabric
I've had these machines. THAT is not normal
d
davewreslt ?
because he didnt remove the transit bolts duuh
what is the model number?
The Bosch Washing Machine Model Number is: WAS20160UC
🤔🤔...Iam gunna put it down to total coincidence that for 2 days I keep seeing washing machines on my UA-cam ( never seen them before may I add) and 2 days ago I just had a new washing machine delivered ... ( Which I fitted my self also 💪💪) which kids say makes a weird noise when spinning ( where it's new I tell them) ...and I get post s like this in my recommendation s 🤔..😁
you still have it?
1:44 Someone calls the cops
1:30 omg what’s wrong with Bosch this wonderful Power of Spin
THAT NOISE!!!
i hear the siren, what is that?
Must be Someone called the cops
hahahahahahhahahahahahhaahahahahhaha the effing cops sound at the back hahahahahaha
What should be done to level it
transit bolts should be removed (you know, the bolts which are at the back of the machine that always come with put at the back of the machine, and some technicians forget to remove it, so you have to remove them yourself if they forget to)
You didnt remove the transits bolts behind the machine
Have u taken off the transit bolts? T_T
You thought the dryer was gonna fall on top of you
where are the transit bolts?
at the back of the washer
the big like umm things at every side
For some reason they seemed to avoid numbers on this washer's control panel at all costs.
Run! even the emergency services came lol
Whirlynerds omg lol
Whirlynerds увам
lkjjjhhh
TRACTOR! TRAIN! PLANE!
Sounds more like an old locomotive 😂😂😂
How in the hell did you fit an F-18 in your bathroom?
Can anyone tell me the model number of the washer? I believe that the model number for the dryer is WTV76100US. I need to call for service.
transport bolt is holding the left bearing, pls remove before running again
thats was funny as hell:)
This machine a Axxis model only and regular spin speed, bur my Logixx 8 Sensitive making a bzzzzzz sound and jumping on 600 rpm
Damn it went crazy enough that the police even came? sounds like .. i don't know.. i'm trying to figure out why my spin cycle is making loud whirling sound like a jet engine. it's brand new still.
You havent heard a brushed motor
Once it spins it was an all nippon airways 787
read the. instruction, and remouve the shipping bolts
maybe next time a dryer and washer next to eachother saves you alot of money otherwise the dryer falls on the ground
Bosch WAS24761TR jumping on the spinning, and make a bzzzzzz sound
P
The washing machine called the police on the owners of whoever had the machine before the owner bought it.
em maybe you should try removing the transit bolts and you can't just have a dryer sitting on top of the washing machine like that. Most dryers have a mounting kit that come with them so you get the chance to stack it on top like that. Anymore shaking and the dryer would have fallen off. I have no idea who installed this machine but they are complete idiots for no remov no the transit bolts. Poor washing machine. Bosch is a very good make
Kieran g
Kieran 2
U
Kieran 0
Kieran h
The whaser had a big stone i think the stone is broked in two
GOOD IT STOPPED ELSE IT MIGHT OF BLOWN UP!!!!!!!!! :D
buy a lg. ... no problems with direct drive
Ttansit bolts bro, bosch is good
@@Carlosvjimm yeah bro
The problem is that the transit bolts where not removed
Suddenly it was an all. Nippon airways 787 taking off😹 (ANA 777🇯🇵)
First is if you put a dryer on top of a washer you must be nuts as that is exactly what happens you damage the whole unit
Shake it off, like a Bosch !
Take out the transit bolts then it will be balanced
Did you put a brick in it ?
What's the maximum spin speed
1000RPM
I saw sock is out drum
Sounds like the hisense the one I have
REMOVING THE TRANSIT BOLTS!!!
Bosch is a good machine my friend there is definitely something wrong with it!
omgs did u call the police ur washer out of control
I have the same one and it's worse .it doesn't shake but everyone in the house has to go outside when it spins it's so loud it hurts your ears .it's like a jet taking off.i will never by this brand again
you should like push the dryer very hard or else it will break really bad...Bosch is really bad :-(
Xtreme 87 no your mom is really bad, it's the transit bolts
Transport bolts !
Mario Lugi Mario Lugi Mario Lugi
No one cares
Take out the transit bolts
Gelmesini çok istiyoruz.
1:39 Stop washing machine bam bam
On the Back of your machine...
Mines black by the way 😁
Lavatrice bagno 😆
try by not filling to full capacity that's why its so unbalanced and by doing so u get better wash results lol:-)
Transit bolts
Remove the Bolts that secure machine
pls pls pls
Never stack bosch washers.
Carbon brushes sound whiny
Replace the washer
Prova a mettere i piedini maggiorati e s sostituire gli ammortizzatori vedrai che non balla piu
forse è meglio se prova a togliere i bulloni di trasporto che bloccano la vasca. Se ci fai caso non si muove di un millimetro
Haha destroying stuff haha tractor sounds
Bosch*