ooooOOOOO SSSSuuuummm dude !!!!! Your system took me 14 years back in my life , a music lover teenager , who used to die for a sound experience from a Panasonic 5 Cd Changer Sound System with 3D Sround and Wide Equlizers and Bass and Loudness and what not .. But financially , all he had was AM radio scanner, and a half broken Cassette player ... OMG man that was my time I had an idea of making a circuit that could work like an Amplifier ... But people told that kid , that his idea was not implementable ...
That's what I. Saying it won't produce more than 10 watt in it's maximum voltage at 60v where as MOSFET power limit is at it's peak according to datasheet and being class a it's highly inefficient amplifier I don't know why these people fool other saying it's 1000 watt something like that
There are class A amps like this, their power is in the mW range and gain is very low. However this one isn't even set up correctly. There is nothing to AC couple the speaker to the output, so a) the power resistor is useless and b) the DC offset would keep the cone off center all the time. However, the cone is not moving a bit when he connects power, and also no crackle when the jack is hooked up. My guess is, he hid a small amp module in the "power brick", connected via bluetooth. The "power rail" carries the actual audio signal, and enters the speaker through the medium sized resistor and ground.
He is misleading people by posting these barely functional circuits with ridiculous ratings. Some are dangerous or will burn out the speaker. Why do you think manufacturers use so many more components to get a proper operating safe circuit? How many people have wasted their time with the garbage he posts?
@@westelaudio943yes actually, when he places the battery on the table, there isnt any sound when the table and battery collides. also the battery is modified, its obvious, also based on calculation, side of the battery says, that its a 6volt battery actually. if we calculate the output wattage, it no more than 0.28Watt, or 280mW. Also when he connects the speaker, or the battery, if the speaker is already connected, there isnt any bumps, most of his diy amplifier isnt working in real condition, i didnt told you new thing i guess.
@@gordonwelcher9598 i actually once blew up my player :) like years ago, luckily i just had a 2-3$ mp3 player, due the decoupling capacior on input was reversed, and i decided to give power to little baby, (i used +12v and -12v on an atx psu.) note: it was 3years ago when i not even had solder iron, nor knowledge about amplifiers. today i built a nice 15watt amplifier for 4ohm, its an AB class amplifier based on quasi complementary pair, giving a whopping 35Volt for voltage rail, it draws half an amp on max volume, it have negative feedback to decrease distortion, it have bootstrap for additional power from the driver, it was a nice project. 2 transistors on the output, (two 13009) and for a driver: c1885 and a912 pair, and a c945 where the signal is boosted from aux.
Los cálculos de potencia para este circuito son 4.5 watts rms max. Considerando Vf=12v, y el amplificador clase A entrega un máximo de Vf/2, es decir la bocina recibe máximo 6vrms, y con 8 ohm de impedancia, la potencia es P=V*V/R, (6*6)/8= 4.5W Corrijo, esta potencia no es RMS, es potencia peak, gracias por la observación a 歸虛
Good job, connecting the battery right up to the speaker, cause that will totally work. For once I thought you were going to build an actual class A amp, but nope, lots of issues with your “circuit”
No hay ninguna duda de que eres una persona muy especial y profesional que bárbaro gracias por compartir tus conocimientos y experiencias con tus amigos y seguidores gracias por compartir tus experiencias con nosotros tus seguidores 😉 😊 👍 🙌 🙏 😊😊😊
Hahahahah Don't be fooled guys. that thing he claims to be a battery has a bluetooth player inside. The audio is actually coming from the media player inside the fake battery. Look at his connections, the red terminal in connected directly to one side of the speaker and the other terminal to the mosfet which I suspect has a short circuit ot the resistor connected to the mosfet case has a short or a wire was put through it to complete the circuit via the heat sink.. Also check when he puts the fake battery down you can see that it is light weight. I would have expected a battery of that side must have some weight . All his videos are fake.
I can test this arrangement with some caveat. So that there was audio output I had to connect the drain from the mosfet to the gate through the 10K resistor. Instead of connecting gate to source. The result was not 1300 W. I think it was much less than the speaker used 8 ohm for 60 W. The mosfet gets very hot.
Aportación? Que aportó, mentiras eso es el aporte que te da, sabes que el video es falso verdad? el amplificador a lo mucho da 3w de potencia, bueno todo el canal miente, de esto no se aprende anda
Bro , you know what , I am not an electrical engineering student , so I dont understand in depth, but I can follow you, the way u did in this video .. Can u make a video for a circuit that inputs music from my laptop or phone , and it must add High Bass , and Loudness & Equilizer sort of functions ??? It would be a blessing
no, dont do it, it will result in your phone/laptop input audio will gonna go in smoke, study first, also i would not recommend following this guy, due his amplifers are deadly for mobile and laptop input use.
while what you did is impressive... it is simply impossible to get 1300 watts from a single ended amplifier running on 12vdc Even if you double the voltage you will never get anywhere near 1300 watts from a single discrete transistor. The laws of physics and amplifier design havent changed. You might be getting between 4 and 5 watts out of your amplifier. Single ended amps are power hungry monsters and can only claim around 40% efficiency. So measure the current draw from your battery and multiply that by the voltage of the battery under load and that will tell you what the amplifier is drawing from the supply. The power output will be only about 40% of the input power. And you absolutely cannot get more power out than you are putting in!!!
He is misleading people by posting these barely functional circuits with ridiculous ratings. Some are dangerous or will burn out the speaker. Why do you think manufacturers use so many more components to get a proper operating safe circuit? How many people have wasted their time with the garbage he posts?
Has anyone tried this? I would imagine that the battery is 12v and probably 10Ah. I would like to see him runs a voltage test on the battery to show us that there is no amp inside it. I will try this in the near future and get back to you.
Yes Ak power amp version 1.0.1 brother AB mode per work karta hai 12 volt sai 30+30 volt(28.4 ampere) create karta hai ua-cam.com/video/HGtOfyjRcIk/v-deo.html
He is misleading people by posting these barely functional circuits with ridiculous ratings. Some are dangerous or will burn out the speaker. Why do you think manufacturers use so many more components to get a proper operating safe circuit? How many people have wasted their time with the garbage he posts?
You wrong, this transistor have P_max 94W and speaker have the sign 500W written with permanent pen, by a simple calculation we find the power (500+94)*2=1188 and this is almost 1300W. Amplifier ofcourse works in Class PM(perpetum mobile) and speaker is constructed from very advanced materials and cheap sticker on magnet :)
Las salidas de audio no se ven muy verdaderas, no se si sea facke o verdad, el audio sale de esa resistencia blanca, donde de cada lado está conectada la bocina no lo se rivk parece falso
Ele usou bateria porque dificilmente temos em casa fonte de 12 volts que forneça amperagem alta. Para esse falante de 500w em 12 volts nesse circuito a fonte precisa entregar 41 amper de corrente para usar a potência total do alto falante. Mas dá sim com certeza, só que a fonte deve fornecer no mínimo 41 amperes , caso a fonte forneça uma amperagem inferior ao que o falante de 500w precisa, ele não vai entregar tudo que pode.
Bro excelente video y q bien. Explicado gracias pero tengo una duda si aguanta trabajar la bocina con ese circuito bastante tiempo o solo es x un tiempo determinado
There are class A amps like this, their power is in the mW range and gain is very low. However this one isn't even set up correctly. There is nothing to AC couple the speaker to the output, so a) the power resistor is useless and b) the DC offset would keep the cone off center all the time. However, the cone is not moving a bit when he connects power, and also no crackle when the jack is hooked up. My guess is, he hid a small amp module in the "power brick", connected via bluetooth. The "power rail" carries the actual audio signal, and enters the speaker through the medium sized resistor and ground.
Rangkaiannya Keren Banget.. hanya saja kalau kita mau Menambah Potensio sebagai Penambah pengaturannya bagaimana Merakitnya..? ok Terimakasih atas Konten nya, Keren Banget jadi Menambah ILMU.. ☺👌👍
La fuente conmutada su entrada es de AC Y su salida DC. La bateria es DC 12V. No veo por que no. No creo que el amperaje de ese circuito electrico sea mucho. Con el multimetro checa donde tienes 12v y listo.
Bom mas esse padrão Rabo Quente na saída, acaba por distorcer os médios. Tenho vários projetos assim e se não for instalado um bom filtro, distorce mesmo.
A MI NO ME FUNCIONO Y LO HICE TAL CUAL, ADEMÁS NO EXPLICA LAS CARACTERISTICAS DE LA BATERIA, AMPERAJE Y VOLTAJE, OTRA COSA ES LA BANANA, SI ES DE TRES CABLES LA QUE MUESTRA, Y SOLO TOMA DOS, SON LA PUNTA Y LA TIERRA LAS QUE UTILIZA????
Hmmm... Really very powerful... Had that thing measured 5watts? Unbelievable... Even the laws of Ohm and power formulas are not what they have been 😳😳😳😂😂😂
He is misleading people by posting these barely functional circuits with ridiculous ratings. Some are dangerous or will burn out the speaker. Why do you think manufacturers use so many more components to get a proper operating safe circuit? How many people have wasted their time with the garbage he posts?
@@manu-06 pensé que cuando decía que era falso, se refería a que no funcionaba nada. Es de lógico que ese circuito no puede dar tan alta potencia. Gracias
*DIY Powerful Ultra Bass Amplifier SSD Computer , No IC , Simple Circuit* ua-cam.com/video/PVN2iqXv5kg/v-deo.htmlsi=jPtXuJCVo-xog2hT
Oye y si kiero k levanté unas 4 bocinas d esas omas grandes Sele ponen más integrados d audio
ooooOOOOO SSSSuuuummm dude !!!!!
Your system took me 14 years back in my life , a music lover teenager , who used to die for a sound experience from a Panasonic 5 Cd Changer Sound System with 3D Sround and Wide Equlizers and Bass and Loudness and what not ..
But financially , all he had was AM radio scanner, and a half broken Cassette player ... OMG man that was my time I had an idea of making a circuit that could work like an Amplifier ...
But people told that kid , that his idea was not implementable ...
This is a Class A amplifier, output is approx. 2.5w with 12v power supply.
That's what I. Saying it won't produce more than 10 watt in it's maximum voltage at 60v where as MOSFET power limit is at it's peak according to datasheet and being class a it's highly inefficient amplifier I don't know why these people fool other saying it's 1000 watt something like that
There are class A amps like this, their power is in the mW range and gain is very low. However this one isn't even set up correctly. There is nothing to AC couple the speaker to the output, so a) the power resistor is useless and b) the DC offset would keep the cone off center all the time. However, the cone is not moving a bit when he connects power, and also no crackle when the jack is hooked up.
My guess is, he hid a small amp module in the "power brick", connected via bluetooth. The "power rail" carries the actual audio signal, and enters the speaker through the medium sized resistor and ground.
He is misleading people by posting these barely
functional circuits with ridiculous ratings.
Some are dangerous or will burn out the speaker.
Why do you think manufacturers use so many more
components to get a proper operating safe circuit?
How many people have wasted their time with the garbage
he posts?
@@westelaudio943yes actually, when he places the battery on the table, there isnt any sound when the table and battery collides. also the battery is modified, its obvious, also based on calculation, side of the battery says, that its a 6volt battery actually. if we calculate the output wattage, it no more than 0.28Watt, or 280mW. Also when he connects the speaker, or the battery, if the speaker is already connected, there isnt any bumps, most of his diy amplifier isnt working in real condition, i didnt told you new thing i guess.
@@gordonwelcher9598 i actually once blew up my player :) like years ago, luckily i just had a 2-3$ mp3 player, due the decoupling capacior on input was reversed, and i decided to give power to little baby, (i used +12v and -12v on an atx psu.) note: it was 3years ago when i not even had solder iron, nor knowledge about amplifiers. today i built a nice 15watt amplifier for 4ohm, its an AB class amplifier based on quasi complementary pair, giving a whopping 35Volt for voltage rail, it draws half an amp on max volume, it have negative feedback to decrease distortion, it have bootstrap for additional power from the driver, it was a nice project. 2 transistors on the output, (two 13009) and for a driver: c1885 and a912 pair, and a c945 where the signal is boosted from aux.
Los cálculos de potencia para este circuito son 4.5 watts rms max. Considerando Vf=12v, y el amplificador clase A entrega un máximo de Vf/2, es decir la bocina recibe máximo 6vrms, y con 8 ohm de impedancia, la potencia es P=V*V/R, (6*6)/8= 4.5W
Corrijo, esta potencia no es RMS, es potencia peak, gracias por la observación a 歸虛
hahhahahahhhhaa 4,5? 1w max
Hola, y como se calcula la ganancia de este circuito?
Hesap çok iyi
I am sure that it is at least 10,000 watts 🙂
Edgar y como se hace si quiero colocarle otro speaker ? gracias
This is more like art than electronic achievement
Excellent!!! your are making an advertising for Microsoft surface too!
Good job, connecting the battery right up to the speaker, cause that will totally work. For once I thought you were going to build an actual class A amp, but nope, lots of issues with your “circuit”
Huge DC offset ... DC amplifier Speaker Burner 🤣😂😅
you make circuit using irf z44n great 🎉❤
what voltage and watts do you use as a power supply?
Batrainya berapa volt
No hay ninguna duda de que eres una persona muy especial y profesional que bárbaro gracias por compartir tus conocimientos y experiencias con tus amigos y seguidores gracias por compartir tus experiencias con nosotros tus seguidores 😉 😊 👍 🙌 🙏 😊😊😊
Hahahahah
Don't be fooled guys. that thing he claims to be a battery has a bluetooth player inside. The audio is actually coming from the media player inside the fake battery. Look at his connections, the red terminal in connected directly to one side of the speaker and the other terminal to the mosfet which I suspect has a short circuit ot the resistor connected to the mosfet case has a short or a wire was put through it to complete the circuit via the heat sink..
Also check when he puts the fake battery down you can see that it is light weight. I would have expected a battery of that side must have some weight .
All his videos are fake.
that's true ! wires are directly to speaker, we all can see at 8:00
thank's for hint !
nice lol, I thought it was legit until he wires the audio out to both sides of the power resistor, couldn't see how that would achieve anything.
Tengo todo el material pero en verdad funciona?no quiero perder el tiempo
@@ash0787 lolw, mine is under construction :)))) i use 5kg transformer :)) at 20volts :)))
I can test this arrangement with some caveat. So that there was audio output I had to connect the drain from the mosfet to the gate through the 10K resistor. Instead of connecting gate to source. The result was not 1300 W. I think it was much less than the speaker used 8 ohm for 60 W. The mosfet gets very hot.
@ Technical DIY How can you say 1300 W? But are we sure? What calculation did you apply?
GRANDE GRANDE GRANDE, MARAVILLOSA APORTACION PARA EL MUNDO,GRACIAS.
Aportación? Que aportó, mentiras eso es el aporte que te da, sabes que el video es falso verdad? el amplificador a lo mucho da 3w de potencia, bueno todo el canal miente, de esto no se aprende anda
Una pregunta.... la caja azul es una batería y de que capacidad
@@JoseRamirez-xc9dg es 12 v es la batería que usan las alarma
Galing na man salamat sa pag share ng talent mo bro
Bro , you know what , I am not an electrical engineering student , so I dont understand in depth, but I can follow you, the way u did in this video .. Can u make a video for a circuit that inputs music from my laptop or phone , and it must add High Bass , and Loudness & Equilizer sort of functions ??? It would be a blessing
ua-cam.com/video/HGtOfyjRcIk/v-deo.html watch video about Ak amp
no, dont do it, it will result in your phone/laptop input audio will gonna go in smoke, study first, also i would not recommend following this guy, due his amplifers are deadly for mobile and laptop input use.
If you are interesting in electrical engineering do yourself a favor and dont watch these videos, there are much more credible sources elsewhere
Nice video sir 👍🏻👍🏻👌👌👌👌👍🏻👍🏻
while what you did is impressive... it is simply impossible to get 1300 watts from a single ended amplifier running on 12vdc Even if you double the voltage you will never get anywhere near 1300 watts from a single discrete transistor. The laws of physics and amplifier design havent changed. You might be getting between 4 and 5 watts out of your amplifier. Single ended amps are power hungry monsters and can only claim around 40% efficiency. So measure the current draw from your battery and multiply that by the voltage of the battery under load and that will tell you what the amplifier is drawing from the supply. The power output will be only about 40% of the input power. And you absolutely cannot get more power out than you are putting in!!!
He is misleading people by posting these barely
functional circuits with ridiculous ratings.
Some are dangerous or will burn out the speaker.
Why do you think manufacturers use so many more
components to get a proper operating safe circuit?
How many people have wasted their time with the garbage
he posts?
1300PMPO possible 😅 lol
Cred că depinde mult și tensiunea de intrare ( semnal )
@@juliusortaleza1486in PMPO everything is possible.🤷🏻👍🏼
1300w PMPO
Excelente saludos desde Metán Salta Argentina
That's like 1 watts at maximum, 1300w would blow that speaker it would be bottoming out really hard smoke and blow, lol
GRACIOSO,,, sale la polilla por abajo del discipador justo cuando arranca el riser or filter de la música del video
🤣
En la caja de descripción pude observar por lo menos 2 mentiras: 1300W y Hi-RES. Haces buen trabajo creando pero por otro lado no mientas.
Si si es verdad, lo le dije son 1300 Watts de consumo, va ni eso, 1300 Watts RMS jamás puede ser 😀👍
What u have used in the end ..that something similar like iron plate
Try to use F-CK69 Gaetanium transistor, it will give 10.000W or how much you want. Don't forget to use Shitanium filter caps for output.
what are the filter caps for?
🤣😂🤣😂🤣
Jajajajaja
Mantaaap bang.bisa buat jual di pasaran ni..di toko toko udh ada blm bang hasil karya nya
1.300w? Or 13w?
13 w 😁😁😁😂😂
This amplifier delivers only 8w
@@sltrickshow3048 1300mW ... miliwatts 🤣🤣🤣
What ever happened to good old schematics and parts lists? It would nice to include a shot of the circuit for us old school guys. Nice video though!
Can use potensio for increas or dicreas?
Done is more than the perfection!
Congratulations blessed ball show stays with God hugs
Has anyone tried this?
I would imagine that the battery is 12v and probably 10Ah.
I would like to see him runs a voltage test on the battery to show us that there is no amp inside it.
I will try this in the near future and get back to you.
Hello, I wanted to ask you, have you assembled a circuit, does it work, how many amps does it consume?
@@ГеннадийМ-ь9ш Hi, thanks for reaching out. No I haven't had the time but I will let you know how it goes. Thanks!
@@irawardmusic thank you, I will wait for an answer from you!
Great work. So much views. 1300W is not a joke.
use Ohms Law it is IMPOSSIBLE here to get 13000W
Good job friend 😁👍👍
God work. ..and easily to make. .thankfully
Kembali lagi sperti biasa, ini ter kongkrit bagus jleger bom.. wow amazing
I like these simple designs....very easy to build for beginners. But 1300watts with a single fet from a 12v battery.....that's impossible.
Yes Ak power amp version 1.0.1 brother AB mode per work karta hai 12 volt sai 30+30 volt(28.4 ampere) create karta hai ua-cam.com/video/HGtOfyjRcIk/v-deo.html
Just try and you can tell💪
He is misleading people by posting these barely
functional circuits with ridiculous ratings.
Some are dangerous or will burn out the speaker.
Why do you think manufacturers use so many more
components to get a proper operating safe circuit?
How many people have wasted their time with the garbage
he posts?
Tem placa amplificada em algum lugar ai
Impressive for such a simple circuit
Hello, thanks, I made it like you, the sound is very weak??
How much is the output watt ?
How much power and Ampier should I give?
1000000v or fack
Both positive speaker and power line are soldered to a resistor that is grounded to the heat sink. That should be getting no sound at all. WTF???
Я в детстве тоже усилители собирал,только маркер тогда ещё не был в ссср,а так бы я нарисовал ,что у меня динамик10гигаватт
Yes, this a great design from 5W heatsink... Probably can output ~1W (maybe 1300 milliwatts?!) of power with huge distortion... HaHa...
this small speaker is 50w and this amplifier is 20w max
Не 50,а 5-10 от силы но чуйка возможно не плохая😅
@@あなたはここで何を見たいですか 10w speaker is printed. on magnet
You wrong, this transistor have P_max 94W and speaker have the sign 500W written with permanent pen, by a simple calculation we find the power (500+94)*2=1188 and this is almost 1300W. Amplifier ofcourse works in Class PM(perpetum mobile) and speaker is constructed from very advanced materials and cheap sticker on magnet :)
Мужики,вы меня дурите😄
@@paolbackman651 anyone can write 500W on a speaker, more likely a 10w speaker, freeze video where he's waving the speaker about 6min.50s
Excelente,pero vieras metido la bocina en una base o una cubeta de agua para ver que tal el sonido encerrado.saludos desde Campeche,Mexico
How would you remove humming sound while conducting to transformer Ac-to-Dc ?
Simple tested solution
Connect 1uf poly cap between audio input + and ground.
Good tiching karte hai 👍👌👌👌👌👌👌👍👍👍👍👍
Wtf? My Peavey Max amplifier had 24, 150 w Darlington power transistors in it, and it was 400 Watts per channel RMS.
excellent video I see what you do congratulations hand up
Can you make a video for making amp for using guitars pls
Las salidas de audio no se ven muy verdaderas, no se si sea facke o verdad, el audio sale de esa resistencia blanca, donde de cada lado está conectada la bocina
no lo se rivk parece falso
Será que pode usar uma fonte de 12volts ao invés da bateria?
Ele usou bateria porque dificilmente temos em casa fonte de 12 volts que forneça amperagem alta.
Para esse falante de 500w em 12 volts nesse circuito a fonte precisa entregar 41 amper de corrente para usar a potência total do alto falante.
Mas dá sim com certeza, só que a fonte deve fornecer no mínimo 41 amperes , caso a fonte forneça uma amperagem inferior ao que o falante de 500w precisa, ele não vai entregar tudo que pode.
@@ramos3246 será que vira testar em um carro?
essa bateria é de 12volt 12 amperes
Bro excelente video y q bien. Explicado gracias pero tengo una duda si aguanta trabajar la bocina con ese circuito bastante tiempo o solo es x un tiempo determinado
SON CIRCUITOS EXPERIMENTALES NO AGUANTAN PARA LARGOS PERIODOS DE AUDIO.YO SOY ARMADOR DE AMPLIFICADORES DE SONIDO.
4.36 из под радиатора выбегает таракан аудиофил))))
😂
Mantap, tp g dijelaskan pasang mosfet ke heatsink perlu isolator apa g, & besaran voltase ACCUNE jg g dijelaskan
улыбнулся)))
Бред какой то?
@@Саша-л4ж7ч рофл!)))
Mạch công suất âm thanh bé mà khỏe phết của nhà nhỉ
Ребят когда он показывает динамик посмотрите там 10 ватт 8 ом😂
how much powwer we need to give it it's glowing on if we give 12 or much higher volt and current
With this single ended drive, the max power output can be easily predicted by the supply voltage and speaker impedance....
Can i use this circuits for boost dc volt?
There are class A amps like this, their power is in the mW range and gain is very low. However this one isn't even set up correctly. There is nothing to AC couple the speaker to the output, so a) the power resistor is useless and b) the DC offset would keep the cone off center all the time. However, the cone is not moving a bit when he connects power, and also no crackle when the jack is hooked up.
My guess is, he hid a small amp module in the "power brick", connected via bluetooth. The "power rail" carries the actual audio signal, and enters the speaker through the medium sized resistor and ground.
Good idea i like 👉🎬
4:36 от девайса отделилась деталь и убежала . Если бы не убежала мощность была бы 13000W . 😄😄😄
китайских Chines 99999999 WATT
Какой-то лютый треш😂😂😂
Просто убираем нолики и тогда по честноку всё будет))
13 Ватт с КНИ-10%.
Это тараканы разбегаются
Rangkaiannya Keren Banget..
hanya saja kalau kita mau Menambah Potensio sebagai Penambah pengaturannya bagaimana Merakitnya..?
ok Terimakasih atas Konten nya, Keren Banget jadi Menambah ILMU.. ☺👌👍
От 12 вольт как то попахивает вранье
Да неа, вполне рабочий вариант. Только качества звука желает лучшего
При 12 вольтах? 1300 ? КПД-1000%-прорыв в физике,понятно,что у них другой "ГОСТ".
I have a weston tv kit but could define the audio section to cut it out so as to use it as an amplifier
muy buen video bien esplicado me gusta la electronica y me gustaria aprender
Where does 1300 Watts come from, if such an irfz44n dissipates a maximum of 94 watts?
Congratulations... excelent!!!!!
Amazing video
Cara!meus cinseros parabéns pela excelente qualidade do seu vídeo. Parabéns!!!!
I’m glad if u can fix the speaker on box. So everyone can hear the bass far better
And not just that if the title of the video is in English at least and English song as well..
@@ricardojuarez291 yup. More enjoyable the diy project.
Gostei 👏 parabéns ficou show de bola 👏 obrigado.
good job bro
Vc tem o layout desse projetinho?????
Mantab terimakasih atas ilmunya semoga sehat selalu aamiin. Bang
Parece ser tão simples de fazer
Ang galing mo talaga idol gawa mo ako nyan
cara gostei muito, só que a ligação do falante está invertida né? batendo pra dentro , o certo é para fora
Esse alto falante ai 500w😏
Se puede alimentar con fuente conmutada de 12 volts?
La fuente conmutada su entrada es de AC Y su salida DC. La bateria es DC 12V. No veo por que no. No creo que el amperaje de ese circuito electrico sea mucho. Con el multimetro checa donde tienes 12v y listo.
Muito massa...ganhou mais um inscrito 👏👏👏👏👏
Agar yah savan to dikha rahe hain aap vah bajega nahin to
👍👍👍 saya punya amplifier merk sunbuck suaranya normal tapi ada gak yang suaranya ada kresek2 itu apa nya ya Om 🙏
Sir, please make this circuit in the supply of three faces please
Can it be fitted with volume best treble control
RMS 5W? :-)
Esta en avalancha toda la potencia se va al parlante pero de seguro se te quema facil necesitan mucha proteccion a no ser que tengas bocinas de sobra
ขอบคุณครับ. หาของเจ๋งๆมาให้เล่น เบสสุดยอด
Est ce que cet amplie na pas de parasites!????
süper okul purojesi ❤👍
❤❤❤❤❤❤ what a great help!!!!
Bom mas esse padrão Rabo Quente na saída, acaba por distorcer os médios. Tenho vários projetos assim e se não for instalado um bom filtro, distorce mesmo.
Como fazer o filtro com potenciômetro?
A MI NO ME FUNCIONO Y LO HICE TAL CUAL, ADEMÁS NO EXPLICA LAS CARACTERISTICAS DE LA BATERIA, AMPERAJE Y VOLTAJE, OTRA COSA ES LA BANANA, SI ES DE TRES CABLES LA QUE MUESTRA, Y SOLO TOMA DOS, SON LA PUNTA Y LA TIERRA LAS QUE UTILIZA????
El amplificador esta dentro de la bateria, es todo fake
Hmmm... Really very powerful... Had that thing measured 5watts?
Unbelievable... Even the laws of Ohm and power formulas are not what they have been
😳😳😳😂😂😂
He is misleading people by posting these barely
functional circuits with ridiculous ratings.
Some are dangerous or will burn out the speaker.
Why do you think manufacturers use so many more
components to get a proper operating safe circuit?
How many people have wasted their time with the garbage
he posts?
Hola. Donde conectas la corneta, la caja verde que es.... Y donde va el positivo y negativo del cable jaks.. No lo dices..
Excelente amplificador, gracias..!
Ati te funcionó??
@@luisdamianduran2744 Saludos, aun no lo he armado aunque tengo todos los componentes.
@@carloszambrano3227 noooo bro no te da 1300w
A lo mucho 10
@@manu-06 eso es correcto, no más de 10w.
@@carloszambrano3227 ci y además un amplificador clase a no puede pasar los 30w
4:37 даже таракан🪳🪳🪳 сделал ноги 🤣🤣🤣🤣
Spk nya 500watt brpa in bang ?
4:35 cockroach .... jajaja good video..!
Yes jajaj I see .
Excelente, buena calidad de sonido. Muy económica y eficiente.
neeee este video es muy falso
@@manu-06 porque???
@@juliopena2336 no existe un amplificador clase a con 1300 watts ._.
Este proyecto a lo mucho 12w
@@manu-06 pensé que cuando decía que era falso, se refería a que no funcionaba nada.
Es de lógico que ese circuito no puede dar tan alta potencia.
Gracias
Dah nyoba gak bisa keluar suaranya
150 w sterio amp ekak hadanda puluvanda organ valata 12" speakers
Total RMS 15 watts
much less than 6 Watts
Qtal uno estéreo se puede hacer para un equipo de sonido que no se consigue la salida?
2 amplifiers is stereo...!
Nice share..
Amazing 👏👍👍