Hello, I have an Ariston Cares Premium 30 EU condensing boiler, until yesterday the heaters turned on regularly, the hot water came only with the heaters on, with only hot water without radiators on, it gave me error 5p2 or 501, now the error I give it both if I turn on the radiators and only open hot water, I noticed that the pressure switch often remains blocked, to unlock it and raise the pressure I have to give it light taps where the pressure gauge is, a week ago, I had cleaned the siphon of the boiler, I also proceeded to clean the duct connected to the collector (I think it's called that), I remember that last year by cleaning the black duct, the boiler worked for me at least for another year, what may depend on the problem? Thank you Simone
I have the same error on my new ariston genus ext 24. Error 5p3 and some times 5p6. Boiler is working fine but 1/5 times the ignition is delayed. Some times the ignition is so delayed there is small explosion sound. Grounding is good, checked. Pressure is in limits checked by the technician. Some say to remove the intake silencer to increase the air volume but I'm not sure.
@@michalaron4784 It is already set by default to the correct value (44). Tried to decrease this value (+re-calibrate) and it's much worse after. Might have to increase it?
Unfortunately not. I can't understand how the boiler can operate normally one day without problems and other times it won't ignite the flame or the flame lifts, it's weird. As if he was dependent on the weather :-), i am ready to order new PCB, but I'm afraid that even after replacing the pcb, the problems will reappear.
@@michalaron4784 @Michal Aron I'm not sure but I think I found the problem. I have Ariston Alteas One Net. It wasn't PCB. The stove has been operating normally for 2 days
@@M0NDO87 so what you did? I am agree - it is not PCB, it is BAD GROUND, this is what cause all kinds of errors.... mine is now working fine since I have made new grounding, it is very important for flame detection...
@@michalaron4784 There was a short circuit inside a combustion chamber. Electrode->white heat shield->heat exchanger. Debris soaked in the heat cover. Temporary I cut off that dirty place by knife but in the future I need to replace heat cover with new one.
salut! Cum ai rezolvat problema pana la urma? Eu am problema asta de un an si merge de obicei cu reset, dar aseara nu a mai cuplat defel dupa 4 incercari.
@@sergiumacavei A avut in sifonul de condens rugina. Am scos sifonul si l-am curatat. Am inteles ca apare din cauza temperaturii mici pe incalzire (35-40 C). Sper sa te ajute.
After 11 months, I got error 309 several times in a week. I cleaned up the condensate drain - again I had rust in it. I„m waiting to see the result.... Have the same board like you, Aron - just check. If not working, I„m prepared to change the 1nF cap.... hope not.
Acesta este finiș pentru centralele Ariston . exact asa face si a mea . trebuie schimbată o placa care costa 1200 lei (aproape cat jumătate din centrală noua-nu se merita) deci o las sa funcționeze asa pana cade de tot si o schimb cu alta marca oricum nu mai vreau Ariston 👎🏻Un mare 👎🏻👎🏻👎🏻 pentru Ariston
Whats the solution for error 504?
Hello,
I have an Ariston Cares Premium 30 EU condensing boiler, until yesterday the heaters turned on regularly, the hot water came only with the heaters on, with only hot water without radiators on, it gave me error 5p2 or 501, now the error I give it both if I turn on the radiators and only open hot water, I noticed that the pressure switch often remains blocked, to unlock it and raise the pressure I have to give it light taps where the pressure gauge is, a week ago, I had cleaned the siphon of the boiler, I also proceeded to clean the duct connected to the collector (I think it's called that), I remember that last year by cleaning the black duct, the boiler worked for me at least for another year, what may depend on the problem?
Thank you
Simone
Take a look on ionization electrode, clean with ScotchBrite, also check combustion chamber, dirt in sifon came from here. Good luck
@@michalaron4784 thanks where is the ionization electrode? Can you send me a link with a image. Thanks
@@michalaron4784 I think I have solved, correct me if I'm wrong, the ionizing electrode, it would be the white ceramic glow plug, right?
@@zicozichetto yes
@@michalaron4784 A part of the white ceramic glow plug was a little blackened, I sanded it, could that be the problem? Thanks so much
For 5P3 in my case i just restarted it a couple of times and it started working again...
I have the same error on my new ariston genus ext 24. Error 5p3 and some times 5p6. Boiler is working fine but 1/5 times the ignition is delayed. Some times the ignition is so delayed there is small explosion sound. Grounding is good, checked. Pressure is in limits checked by the technician. Some say to remove the intake silencer to increase the air volume but I'm not sure.
I would check soft start parameter in settings, right value is in instal manual for your boiler
@@michalaron4784 It is already set by default to the correct value (44). Tried to decrease this value (+re-calibrate) and it's much worse after. Might have to increase it?
I have the same problem. Any progress?
Unfortunately not. I can't understand how the boiler can operate normally one day without problems and other times it won't ignite the flame or the flame lifts, it's weird. As if he was dependent on the weather :-), i am ready to order new PCB, but I'm afraid that even after replacing the pcb, the problems will reappear.
@@michalaron4784 @Michal Aron I'm not sure but I think I found the problem. I have Ariston Alteas One Net. It wasn't PCB. The stove has been operating normally for 2 days
@@M0NDO87 so what you did? I am agree - it is not PCB, it is BAD GROUND, this is what cause all kinds of errors.... mine is now working fine since I have made new grounding, it is very important for flame detection...
@@michalaron4784 There was a short circuit inside a combustion chamber. Electrode->white heat shield->heat exchanger. Debris soaked in the heat cover. Temporary I cut off that dirty place by knife but in the future I need to replace heat cover with new one.
Update: after 3 days of working, problem came back :(
Nu merge încălzirea la calorifere, numai apa caldă merge
Cauta pe net forumul Elektroda : " Ariston Genus One System: Addressing Gas Boiler Errors 501,504,309,5p3 After Replacing Parts "
Какой транзистр ставили
whatch this, this could help you : ua-cam.com/video/5zcBxWMzmfw/v-deo.html
I had error 504 flame lift on Ariston Genus One 24 kw and I fixed it like this guy did: ua-cam.com/video/c1VTzf2SUHw/v-deo.html - it was full of rust.
salut! Cum ai rezolvat problema pana la urma? Eu am problema asta de un an si merge de obicei cu reset, dar aseara nu a mai cuplat defel dupa 4 incercari.
@@sergiumacavei what error code you have,?
@@michalaron4784 503 or 5p something. It is something related to the lack of flame.
@@sergiumacavei A avut in sifonul de condens rugina. Am scos sifonul si l-am curatat. Am inteles ca apare din cauza temperaturii mici pe incalzire (35-40 C). Sper sa te ajute.
After 11 months, I got error 309 several times in a week. I cleaned up the condensate drain - again I had rust in it. I„m waiting to see the result.... Have the same board like you, Aron - just check. If not working, I„m prepared to change the 1nF cap.... hope not.
Acesta este finiș pentru centralele Ariston . exact asa face si a mea . trebuie schimbată o placa care costa 1200 lei (aproape cat jumătate din centrală noua-nu se merita) deci o las sa funcționeze asa pana cade de tot si o schimb cu alta marca oricum nu mai vreau Ariston 👎🏻Un mare 👎🏻👎🏻👎🏻 pentru Ariston
Cea mai,,LEDY" Ariston...
Cauta pe net forumul Elektroda : " Ariston Genus One System: Addressing Gas Boiler Errors 501,504,309,5p3 After Replacing Parts "
Что за немое кино?