Classic mini KAD Internal Gear linkage kit and how to fit it. PART 2
Вставка
- Опубліковано 8 вер 2024
- This is a start of another transformation to my classic mini. I’m fitting a KAD internal gear linkage kit. In part two I finish off the fitment and you now have the measurement to cut the hole, sadly I did not. LOL. Wat h for the do and do not’s 😬😬😬😬
If you would like to see any more Mini mods being fitted to my car then why not subscribe and like this video.
If you like my channel and you would like to support me please buy me a coffee, all monies raised will go back into the channel. the link is below.
www.buymeacoff...
Thanks for watching
Great Video on this KAD kit, with the aprox measurements for the rod hole. Helpful intruction KAD should hand out too!
👍👍
Thanks and good luck 👍👍
Hi, just found this video, awesome video and very intuitive, we are currently building a classic mini for club sport and just about to start putting in an internal gearshift ourselves so this has been a real help.
We are uploading parts of the build onto my you tube channel.
keep up the good work cheers Marty.
Thanks buddy let me know you channel as I will subscribe. 👍👍
@@RRW no worries it's marty's projects
@@martysprojects all subscribed 👍👍👍👍
Thank you so much for this video. I appreciate the measurements you wrote on the bulkhead as well. That will help me as well as a ton of others in the future.
My pleasure, I really struggled so thought it would save everyone lots of hassle 👍👍
Oh I love your channel as well. So chuffed you commented on my channel. Thank you
@@RRW Thank you! You made a great video on a subject I really wanna do in my car. Had to tell ya so! :-) keep up the good work.
Great vide .Had a go at mine yesterday. Unfortunately can't get any of the gears, I didn't pay enough attention when taking apart my old linkage and think I added a small plastic bush to the inside rather that outside ... You highlighted a "washer" to retain the grease. Really useful to help me figure out mine 👍👍 . Looking forward to the other update videos 👌
make sure the lower knuckle by the gearbox, is tight loosen the top knuckle put the car into reverse then tighten the top knuckle going into the housing and then you should be able to find your gears . I also had the same problem. it all depends what gear your gearbox is in when you remove the roll pin.
are you on Instagram if so let me know your Instagram name. I will do video and explain to you what you need to do and that will hopefully help you out🤙🤙🤙🤙or message me
at #retromini1330 and I will reply👍👍
Just uploading a video on how to do it🤙🤙
Brilliant video 🤙
Thanks buddy
well detailed video, I appreciate the effort that has gone into this!
Thanks buddy 👍
I have done a how to set it up once fitted on my channel, thought you might like that as well👍👍
Thank you!!! I am going to install this system and your videos classify all my doubts! 👍
No worries buddy, I wad so worried about fitting it so I thought I would share it with everyone to help. Thanks for your comment. You will love it when you get it.
I think a magic wand gear lever gaiter would probably cover the hole you made? I bought a copy gear change that someone has made and that had a magic wand gaiter with it - I saw pics of it in the car and it looked right although I guess that gaiter was strictly designed for the earlier round tunnel so won't fit quite as neatly to a later square tunnel like yours (and mine!)
Cheers for the vid and especially the measurements as that was the bit I was worried about.
No worries, thanks for watching. I hope it all works out with measurements ok 👍
Hi! Great and Nice video on this KAD kit. Can you work handbrake ? I would like to know whether the handbrake is interfere for fixing-bracket parts of this kit.
Thanks buddy . The good news is you get a spacer in the kit that move the handbrake sideways a bit avoiding the gear change. But that said it is tight. 👍👍
Great vid mate!
Thanks bud 🤙