What these Internet Techs fail to realize is that there's still a few of us left that were taught by old dudes. Old School Men who got shit done and done right.
Fantastic video. Some people would complain if they had a job sampling ice cream. I like the way you answer all of the questions and stupidly of armchair quarterbacks, and know it all. It really amazes people when they see a real professional MAN at work.
I feel obliged to point out that if YOU use a 20 pound Ford Tune-Up Tool(aka Sledgehammer) on a Vulva, Vulva recommends YOU paint IT Pink first so YOU don't hurt the Vulva's feelings...🤣
If you think that 16 lb hammer is going to damage a bearing. Well what do think that is worse than 12- 14,000 lbs hame erring it on a pot hole or just bouncing down the with a full load on it. Come. On wake up people
gotta love those back yard shade tree super techs greasing those wheel bearings on their 6x4 or boat trailors gives them all the experience they need. Which of course gives them all the experience to know any thing about heavy industrial applications
People are really so stupid to say you’re destroying the bearing by pounding out a stud? If you could destroy that bearing with a hammer wouldn’t you think that the bearing would break apart after a couple bumps on the road with the weight of the truck at speed behind it?
❤ I had the exact same thing when using the air hammer I only use a 10 lb with the cut short I'm too old to swing a 16 lb you can swing a heavy hammer lightly but Not a light hammer heavy. keep swinging bob is smarter than a lot of people
You sir, are absolutely hilarious🤣 You have the braggadocio and the moxie to back it up. Just love your videos.👍 Who knew frame bending could be such fun!
i cannot believe that someone who watches this sayes it will hurt the bearings,i am a retired truck mechanic,did it for 45 years. a big truck loaded weighs 80,000 pounds ! so when it hits a pot hole that is more shock than hitting it with a hammer! i had a truck that went to jersey 5 times a week it hit a pothole near new york city and it knocked the lower radiator off! more than once ,so the wheels stayed on !!!! i did some alignment but nothing like you do. like to have done some.like your stuff keep up the good work . ps dont know how many axle studs i bent but it takes some skill swing that big a hammer.
dude hits a wall in a 75,000 lb truck, bearings are fine.... but if you knock the studs out with a sledge youre damaging the bearings all of the sudden lol
Keep doing you! Most of the comments are from people that don’t know how to do it but their book tells them you’re doing it wrong. Diarrhea of the mouth constipation of the brain…
Wow !!! Thankyou that was great 💪I was heavy truck tech for 27yrs it blood guts and muscle 💪 You got that perfect!!!!! Thanks again for showing what a real heavy truck tech is 👍👍 Keep up your awesome videos 👍👍👍💪💪💪
It has been awhile since I worked on trucks. But I would say hitting a concrete wall or a f150 would be alot harder on them there wheel bearings, then hitting them with a 16 lbs hammer. The only thing you are going to knock out with that air hammer is the filling in your teeth, when trying knock out large truck wheel studs with it!!!
I think its great just to watch you do your job, you are a pro and it shows. I had no clue as to how these trucks are repaired. Thanks for taking us along for the ride.
A taper roller bearing is one of the toughest steels, taking so many tons of weight for literally millions of miles, at the same time supporting about 200 pounds of wheel and keeping it in place over rough roads at 60 mph plus,,,,,,, 🤣🤣🤣😂😂😂🤣😂 I mean come on, as far as that bearings concerned, it’s being tickled with a feather. Every joint strip or pothole smacks that bearing way harder. Even if that hub was on a trailer from over a hundred years ago with plain bronze for a bearing it’d still shrug off those hammer smacks 😅😅
to hit a big truck hub hard enough to damage the bearings would require a wrecking ball. that normal swing maby has 4-500 lbs of force. then divide that up by the surface area of the bearings. and is basically nothing.
Bahaha YES!! Dude I love the way you react to people. Probably the same way I'd respond to dumb shit haha. If your ever up towards East TN I'd love to meet you hell I'd even buy you a beer . These "keyboard warriors " just won't ever understand what working on tractors is like
Using hammer for stud removal is a great idea even for little bitty cars no bearing damage unless there is already an issue with the bearing. I've also learned that using the focus fine tip punch on the air hammer works way better than the Hammerhead bit. time is money
Hold up! The 16# hammer blowing a stud out does more damage to the studs than the massive tractor that weighs, no idea, 30k #, that just ran into a wall. If hitting the wall didn't blow up a bearing, some dude hitting studs with a hammer doesn't even know its happening.
I had an aggravating day at the shop. Thanks for the humor! Some say there is a bit of truth in humor. This humorous video has a lot of truth in it. I wonder how many of those key board worriers ever got their hands dirty for a living?
The Internet is full of expert keyboard warriors and they all have one thing in common. They're all full of sh!t! Keep on keeping on and do what you do!
I love your content sir! And putting out the information to share with us, keep the videos coming and screw the people who don’t know what they are talking about!!!!
I work on garbage trucks and man I know exactly what kind of shop you work at. The one we send all the heavy af jobs too that takes an expert an hour & an apprentice a year! I'll be a happy filter fairy if ya'll will swap my spring packs, deal?
Brother ive been a heavy duty diesel mechanic since 1996 and the way you work is exactly the way you perform those repairs... I've been doing it that way for almost 30 years ... keep on busting brother
They is always some keyboard warriors 🙄 out there that will be putting their two cents in where it wasn't asked for! Like you said, "you do you." And the " not used to working with that large of a tool", had us rolling 🤣 🤣🤣🤣🤣🤣
I'm almost 63 and have been doing this since I was a little kid in my grandfather's shop. I used to get so greasy in my single digit years that my mom would wash me before I came into the house at night. What I can tell you is this. Most tech school mechanics suck. They don't have a clue. I don't know if it's the schools, or that they started too late in life. But they are all full of the kind of stupid stuff you are addressing in this video
I don't know why people question you about being competent. If you weren't good at your job, you wouldn't have one . I actually learn all kinds of things watching this show, and I've been around for 60 years. I do offen wonder 🤔 just how many bodies do you have barried behind that shop 🤔 ? ........ other than wondering about the corpses, you seem like you do a good job and definitely earn your money 💰.
I don’t think I’ve seen you do anything I would have a problem with! The one thing I really don’t have a problem with is your music selection, that is spot on!!
I knew a big freight company workshop when they had to remove chassis bolts they were cut off with an oxy because they replaced them with new ones. This looked crazy but it was efficient and cost effective. Cheers
Hahahaa keyboard warriors are wonderful. "if you ain't got nothing nice to say, why don't you shut the fuck up" It's all in the approach I guess. Keep up the great videos. How can you argue with a guy with hair like that anyways! Hahaha later buddy!
As a old doctor told me years ago, Everyone knows how to cut meat but a butcher.
“oOOOooo, I’m a MasTeR tEcH now”😂
Air hammers almost always suck.
What these Internet Techs fail to realize is that there's still a few of us left that were taught by old dudes. Old School Men who got shit done and done right.
Dude that though a 16lb sledge was gonna wreck those bearings apparently never seen a pothole 🤪
Those bearings hold their portion of 40 tons at any time. You're totally not damaging them with that 16-pound hammer.😂
Not to mention every pothole at 65 mph you hit with each axle at 40+ ton 😂
I thought the same thing.
Fantastic video. Some people would complain if they had a job sampling ice cream. I like the way you answer all of the questions and stupidly of armchair quarterbacks, and know it all. It really amazes people when they see a real professional MAN at work.
I feel obliged to point out that if YOU use a 20 pound Ford Tune-Up Tool(aka Sledgehammer) on a Vulva, Vulva recommends YOU paint IT Pink first so YOU don't hurt the Vulva's feelings...🤣
Oh thats what the air hammer was doing.
Hitting it in the right spot.
👀
If you think that 16 lb hammer is going to damage a bearing. Well what do think that is worse than 12- 14,000 lbs hame erring it on a pot hole or just bouncing down the with a full load on it. Come. On wake up people
Or hitting a wall
I think you've found your winning formula here. Mechanic work+ sarcasm and disdain.
I love the finesse in striking the cap… perfect
😅😅😅 Great Video and thanks for the laughs. Those who CAN NOT are always the HATERS. Keep the great videos coming.
I'm very impressed with your accuracy of smacking those studs out. I bet theres s ton of people who think they can do it but really cant.
gotta love those back yard shade tree super techs
greasing those wheel bearings on their 6x4 or boat trailors gives them all the experience they need. Which of course gives them all the experience to know any thing about heavy industrial applications
People are really so stupid to say you’re destroying the bearing by pounding out a stud? If you could destroy that bearing with a hammer wouldn’t you think that the bearing would break apart after a couple bumps on the road with the weight of the truck at speed behind it?
10 out of 10, would watch Bendin again.
I have been doing this type of work for 50yrs and you’re doing it right
But I don’t have to tell you that
❤ I had the exact same thing when using the air hammer I only use a 10 lb with the cut short I'm too old to swing a 16 lb you can swing a heavy hammer lightly but Not a light hammer heavy. keep swinging bob is smarter than a lot of people
40 year Master tech here and you've done it the way i have for all those years. Never a return for using a big hammer... Keep up the good work.
You sir, are absolutely hilarious🤣 You have the braggadocio and the moxie to back it up. Just love your videos.👍 Who knew frame bending could be such fun!
Hahahaha 🤣🤣 That ending was the absolute greatest....I almost pissed myself laughing so hard 🤘🏻
Emergency!!!
Every truck he has worked on must be condemned immediately!
😅
We enjoy watching you and Bob teach us some of the lost arts of getting it done 🤘
The only positive about the negative comments is we get fun videos like this to watch.
Everyone a professional on here. Fact is he gets the job done!
i cannot believe that someone who watches this sayes it will hurt the bearings,i am a retired truck mechanic,did it for 45 years. a big truck loaded weighs 80,000 pounds ! so when it hits a pot hole that is more shock than hitting it with a hammer! i had a truck that went to jersey 5 times a week it hit a pothole near new york city and it knocked the lower radiator off! more than once ,so the wheels stayed on !!!! i did some alignment but nothing like you do. like to have done some.like your stuff keep up the good work . ps dont know how many axle studs i bent but it takes some skill swing that big a hammer.
I fkn love this cat so much lol. The experience is extremely obvious it's funny when people try to pick it apart
Love your videos get good laugh from all the jealous people out there the way u give it back to them keep it up
If Sam Kinison was an awesome frame mechanic, he'd be this guy! R.I.P. S.K.
I'm a retired fleet mechanic I always used my small sledge hammer doing that same work I never owned a air hammer
Oh the trolling is strong with this one....😅
That was pretty funny. 😆
I like your style, knowledgeable and it’s easy to tell you are good at what you do. 👍
Love the knowledge, feed it to em
It's TKO in the first round brother we believe in you sir you are a smart man 💯🏁
I detect a slight note of sarcasm in your voice. LOL !
Been a Diesel mechanic for two years now snd I’d love to work under this guy
Awesome! Oh and make sure to get ALL the rag fuzz out so it does not tear up the bearing!
dude hits a wall in a 75,000 lb truck, bearings are fine.... but if you knock the studs out with a sledge youre damaging the bearings all of the sudden lol
YOU THE MAN.
Its funny the shit people complain about , Love Benden's chuckle after the cap, Cheers from Australia
So, hitting the studs with a hammer puts more force on the bearing than a loaded truck hitting potholes ?
Top man! keep them coming. UK
We hammer out studs all the time . Never had a bearing failure from it.
You should show how you put the new studs in, I'm sure that will really get the keyboard mechanics in a frenzy!!!!! Lol
That oil cap exploding made my day! 😂
Keep doing you! Most of the comments are from people that don’t know how to do it but their book tells them you’re doing it wrong. Diarrhea of the mouth constipation of the brain…
in my semi professional option beating on a wheel stud is nowhere near the same shit kicking those bearings take day to day, crazyness
hahahahah should watched the whole video first, hilarious stuff, keep on keepin on
Are you a Semi Professional, or a semi-professional? 🤣
@@A6Legit that's up for you to decide buddy!
@@tra6ic741 the world may never know. Lol
Nice work. Hitting each one while hub was turning is skill. One hit per stud.
Now I need a sledge hammer in my workshop
you are a legend!
Great clip man!stick it to the "Supa techs"!show em how it should be done🤙
Thanks for the show Devin 🍻
Wow !!! Thankyou that was great 💪I was heavy truck tech for 27yrs it blood guts and muscle 💪 You got that perfect!!!!! Thanks again for showing what a real heavy truck tech is 👍👍 Keep up your awesome videos 👍👍👍💪💪💪
Seems like a bearing that is designed to support 10s of thousands of pounds can probably handle a 12lb purse hitting it 🤷♂️
It has been awhile since I worked on trucks. But I would say hitting a concrete wall or a f150 would be alot harder on them there wheel bearings, then hitting them with a 16 lbs hammer. The only thing you are going to knock out with that air hammer is the filling in your teeth, when trying knock out large truck wheel studs with it!!!
I think its great just to watch you do your job, you are a pro and it shows. I had no clue as to how these trucks are repaired. Thanks for taking us along for the ride.
Don’t listen to the dummy’s that probably never had there hand’s dirty keep doing you man love your videos
Good video, your not doing anything wrong. Keep up the good work. Great frame straightening work too.
A taper roller bearing is one of the toughest steels, taking so many tons of weight for literally millions of miles, at the same time supporting about 200 pounds of wheel and keeping it in place over rough roads at 60 mph plus,,,,,,, 🤣🤣🤣😂😂😂🤣😂 I mean come on, as far as that bearings concerned, it’s being tickled with a feather.
Every joint strip or pothole smacks that bearing way harder.
Even if that hub was on a trailer from over a hundred years ago with plain bronze for a bearing it’d still shrug off those hammer smacks 😅😅
That last part was gold lmao. Are these people working on grand papys 5500 gmc? Wtf man! 🤦♂️
to hit a big truck hub hard enough to damage the bearings would require a wrecking ball. that normal swing maby has 4-500 lbs of force. then divide that up by the surface area of the bearings. and is basically nothing.
I like your style!
Love this channel. Keep doing it your way and listen to your customers, not the children leaving comments.
Love the wit there
Bahaha YES!! Dude I love the way you react to people. Probably the same way I'd respond to dumb shit haha. If your ever up towards East TN I'd love to meet you hell I'd even buy you a beer . These "keyboard warriors " just won't ever understand what working on tractors is like
ADHD for the WIN
rock on,i love your sarcasm!
I love watching you do your thing. It brings back memories of when I would help my grandpa work on earth moving machinery. I was his gofer.
Trolling the trolls. Gotta love it
There's only one stud i see in all these videos, and nothing is knocking him out.
Using hammer for stud removal is a great idea even for little bitty cars no bearing damage unless there is already an issue with the bearing. I've also learned that using the focus fine tip punch on the air hammer works way better than the Hammerhead bit. time is money
Those bearings would laugh off some hammer strokes..
Hold up! The 16# hammer blowing a stud out does more damage to the studs than the massive tractor that weighs, no idea, 30k #, that just ran into a wall. If hitting the wall didn't blow up a bearing, some dude hitting studs with a hammer doesn't even know its happening.
I had an aggravating day at the shop. Thanks for the humor! Some say there is a bit of truth in humor. This humorous video has a lot of truth in it. I wonder how many of those key board worriers ever got their hands dirty for a living?
Only time they get grease on their hands is from eating fried chicken. I eat fried chicken but I also work.
Perfect
Well sir. At the speed your knocking the studs out your damaging the rotor! 😂
Nah, he's just shot-peening it a bit to harden it up.
The Internet is full of expert keyboard warriors and they all have one thing in common. They're all full of sh!t! Keep on keeping on and do what you do!
8:55 ..... ZERO brinneling noted. Yer all good, Bruh. Thanks fer the skoolin!
I love your content sir! And putting out the information to share with us, keep the videos coming and screw the people who don’t know what they are talking about!!!!
Love the video
I work on garbage trucks and man I know exactly what kind of shop you work at.
The one we send all the heavy af jobs too that takes an expert an hour & an apprentice a year!
I'll be a happy filter fairy if ya'll will swap my spring packs, deal?
great stuff brother! found this channel recently. keep hurting those feelings!
Bro you are one of my favorite old school mechanics i love when you put people in their place with facts
Brother ive been a heavy duty diesel mechanic since 1996 and the way you work is exactly the way you perform those repairs... I've been doing it that way for almost 30 years ... keep on busting brother
They is always some keyboard warriors 🙄 out there that will be putting their two cents in where it wasn't asked for! Like you said, "you do you." And the " not used to working with that large of a tool", had us rolling 🤣 🤣🤣🤣🤣🤣
If the hub can't handle a swat from a hammer,how is it supposed to carry it's share of 9-20k pounds?
I'd be willing to bet that a pothole at 55MPH would be rougher on the bearing and they just keep working.
You are doing awesome, don't feed the cry babies, they love attention. Lots of good knowledge you are sharing with the world in these videos.
I'm almost 63 and have been doing this since I was a little kid in my grandfather's shop. I used to get so greasy in my single digit years that my mom would wash me before I came into the house at night.
What I can tell you is this. Most tech school mechanics suck. They don't have a clue. I don't know if it's the schools, or that they started too late in life. But they are all full of the kind of stupid stuff you are addressing in this video
That is great, show the haters some hammer time! good job.
Air HammerDrives Every Body Around Ya Nuts. Learn To Use The Hammer Like Bendo Duz. Frm A 35 Year Shop Floor Mechanic.
Man I love your humor. Gets me gigglin'. Nice job, why peeps got to direct a man that's doin' this every day. I have no clue
I don't know why people question you about being competent. If you weren't good at your job, you wouldn't have one . I actually learn all kinds of things watching this show, and I've been around for 60 years. I do offen wonder 🤔 just how many bodies do you have barried behind that shop 🤔 ? ........ other than wondering about the corpses, you seem like you do a good job and definitely earn your money 💰.
Hilarious seeing someone air hammer studs. I would have said.. Come on! This your first day on the job? 😆
A evil twin to Bob would be a say, 'Bart' & he has the middle finger/pointy thingy for them troll boy's benefit.
You could never swing that hammer and hit as hard as a pothole at 75mph with a full load. More people need to understand basic physics.
just what I was thinkin
Those of us that are paying labor by the hour--we thank you for saving us money !!!!
I don’t think I’ve seen you do anything I would have a problem with! The one thing I really don’t have a problem with is your music selection, that is spot on!!
You keep posting and I'll keep watching,!!! They need to watch some overseas frames straightening, that is what I remember from my youth!!!😅😅😅😅😅
I knew a big freight company workshop when they had to remove chassis bolts they were cut off with an oxy because they replaced them with new ones. This looked crazy but it was efficient and cost effective. Cheers
All good to me keep doing this you know what you are doing keep up the good work
That was funny!
Hahahaa keyboard warriors are wonderful. "if you ain't got nothing nice to say, why don't you shut the fuck up"
It's all in the approach I guess. Keep up the great videos. How can you argue with a guy with hair like that anyways! Hahaha later buddy!
Got my autographed bob, love it! Brought it into the shop definitely gonna use it anytime someone asks me something!