They had scroll technology around 60 years ago. They had a seal between the scroll and it routinely failed. The machining process gets the tolerance much lower now so the gasket is no longer needed. I’ve seen the cut outs of these scrolls but never seen a running cut out. This was very cool thanks for the video.
@@jamesv4463 the scrolls are covered in oil. The oil acts as a seal that covers the microgaps and prevents the air from leaking. It also covers the surface of the scrolls and prevents them from getting cold welded together.
@@aryanarya8741 from my understating the metal was actually making the seal, hints why this kind of compressor can actually improve over time. it wears into eachother
@@jamesv4463 it is impossible for a machine like this to run without oil in my opinion. the cold welds will increase the friction so much and will destroy the seal. no matter how perfect the seal is there is oil involved that protects the surface
That is a fantastic video! You are right there are three bearing, drive bearing, middle is the straddie bearing and the lower bearing.The lower bearing live in the oil so it does see as much wear.The straddie bearing take a ton of abuse especially on liquid flood back.I don't see that much wear on the upper bearing when I take them apart. Five Star video!
Wow. Great feedback @dizziedallas . I worked on a unit today that had a scroll that was vibrating terribly. My guess is the compressor had liquid flood back recently since there were no pressure switches installed and the system leaked out all the refrigerant. I found the compressor off on internal thermal overload
Thank you So MUCH for this video. For years I have wonder how a piston compressor could fit my window AC unit!!! Now I understand.. It never was one!!!
one of the failure modes for these compressors is the bottom bearing which is held in by 2 to 4 cap screws. the screws can loosen up and the bottom bearing will knock around,
I used to work at the factory that made that little plastic tube that you see attached to the side of the fixed scroll. Perhaps an older unit. The ones we made were of black plastic instead of white.
is the noise at 1:34 "like a moped" is normal ? My heating pump is doing same noise, I've had a pac for a few years, and I find it surprising that it makes this noise.
Hey Ulises I'm a little late on the vid lol I have a ZR125KC scroll that I want to tear open and see what's going on on the inside. What VFD do you recommend for that compressor ? We use 220V out here and 380V 3 phase. Just not sure what capacity I should use. It'll just be dry testing the motor like you reviewed here
I love VRV variable Refrigerant volume system that's why I love and like liked this video and I am HVAC technician so i loved the AC video but this one is really ossooom...✌️
@@actechformallyyomama746 the coldest part of the system. That's why you have a crankcase heater is to keep the compressor warm and avoid flooded starts. Sorry and I meant refrigerant migration not oil migration.
Honestly it would been nice if you could given a tutorial explanation in this operation and what the parts are actually doing for us Dummies 101. Thanks.
Karl-Alfred Römer their are ports for oil to run through the entire compressor to lubricate the moving parts. Oil runs through the entire refrigerant circuit.
Joe Shearer lol yeah I did. That vfd goes up to like 500 htz. I was scared to take it up to 100 htz. Almost double the rpms. I have another compressor. I might try to take it to 200 lol.
Farther down Joe Shearer prompted the original poster's reply: "Joe Shearer lol yeah I did. That vfd goes up to like 500 htz. I was scared to take it up to 100 htz. Almost double the rpms. I have another compressor. I might try to take it to 200 lol."
That's great that you did this. Even people who "know" what the scroll is can learn about them. Thank you,
They had scroll technology around 60 years ago. They had a seal between the scroll and it routinely failed. The machining process gets the tolerance much lower now so the gasket is no longer needed. I’ve seen the cut outs of these scrolls but never seen a running cut out. This was very cool thanks for the video.
I would like to know how they don't cold weld. It's hiding a secret. In the factorys you cant even take a phone Into where they make the scrolls
@@jamesv4463 the scrolls are covered in oil. The oil acts as a seal that covers the microgaps and prevents the air from leaking. It also covers the surface of the scrolls and prevents them from getting cold welded together.
@@aryanarya8741 from my understating the metal was actually making the seal, hints why this kind of compressor can actually improve over time. it wears into eachother
@@jamesv4463 it is impossible for a machine like this to run without oil in my opinion. the cold welds will increase the friction so much and will destroy the seal. no matter how perfect the seal is there is oil involved that protects the surface
This is exactly what I wanted to see,
thank you..
it's hard finding video like this show the inner workings of a compressor
That is a fantastic video! You are right there are three bearing, drive bearing, middle is the straddie bearing and the lower bearing.The lower bearing live in the oil so it does see as much wear.The straddie bearing take a ton of abuse especially on liquid flood back.I don't see that much wear on the upper bearing when I take them apart. Five Star video!
dizziedallas thanks man. I appreciate it.
Yes a fantastic video. BTW my COM07359 5ton has a one way high side valve so there is no liquid blow back.
Wow. Great feedback @dizziedallas . I worked on a unit today that had a scroll that was vibrating terribly. My guess is the compressor had liquid flood back recently since there were no pressure switches installed and the system leaked out all the refrigerant. I found the compressor off on internal thermal overload
Running cut out is amazing!!.. Thank you so much
Best teardown I've seen, thanks for uploading, man!
mike_HVAC thanks man.
@@UlisesPalacios please make a video how to make ? motorbike pump in using air conditioner compressor.
Thank you So MUCH for this video. For years I have wonder how a piston compressor could fit my window AC unit!!! Now I understand.. It never was one!!!
Ii have to thank you for your efforts, you knew how to research and figure out how to demonstrate for yourself and others how it works.
one of the failure modes for these compressors is the bottom bearing which is held in by 2 to 4 cap screws. the screws can loosen up and the bottom bearing will knock around,
Thank you for taking the time to shoot and share
I used to work at the factory that made that little plastic tube that you see attached to the side of the fixed scroll. Perhaps an older unit. The ones we made were of black plastic instead of white.
Sparky Arcblast that’s cool. I’m guessing that’s for oil. To drain back into the crankcase
Parabéns melhor vídeo já feito! Graças a ele consegui entender o funcionamento do sistema!
Very cool!!! You have no idea how cool an important and the amount I learned from this!! Thanks!!
Это пожалуй лучшее видео об устройстве спирального компрессора.
13:38 does it need that much power to run how much power does it need to run fully?
Awesome! Great piece of technology. I was so curious now I understand.
Pretty sure you’ve been taking things apart since about the age of three 😂. Extremely impressed with your lab work.
Sounds like a Ford model t
Peace
Great effort. Nice to see what happens inside a scroll compressor.
How to remove water mixed in oil incase submerged evaporater develop a leak?
is the noise at 1:34 "like a moped" is normal ? My heating pump is doing same noise, I've had a pac for a few years, and I find it surprising that it makes this noise.
THATS HOW THIS WORKS!? I NEVER KNEW. WHAAAAAT!?!? THANK YOU!!!!
I assume that is a three phase motor with variable speed drive.
VERY GOOD CONTENT! BECAUSE NO ONE KNOWS ABOUT COMPRESSOR HOW ITS WORKS ? THANKS FOR YOUR VIDEO
Super cool. Thanks for taking the time.
0:21 and 0:29 Was that the oil??
Did you try minimum freq and RPM, when the compressor starts to lubricate itself properly please? (Oil pump start pumping oil)
Good ilustration-SUBSCRIBED
Hey Ulises I'm a little late on the vid lol
I have a ZR125KC scroll that I want to tear open and see what's going on on the inside. What VFD do you recommend for that compressor ? We use 220V out here and 380V 3 phase. Just not sure what capacity I should use. It'll just be dry testing the motor like you reviewed here
Very cool! Thanks for sharing!
Fox Family Heating and Air Conditioning thanks Greg.
a little Madd scientist action , that was neat
JH HVAC & Plumbing thanks man
JH HVAC & Plumbing thanks buddy
Nice little VFD
Great video! What Model VFD controller are you using?
I'd love to know that as well.
Very good I was waiting to see it.THANKS
Variable DC power supply for this experiment?
Very good video to know about scroll compressor but safety is the first
Thank you. Great presentation.
Can you run compressed air thru the outlet and make a three phase alternator or is there a check valve to prevent this?
There’s a discharge check valve to prevent reverse rotation. Scrolls only run in one direction
What kind of amp draw is the compressor running with no load?
This is a great video. Thanks for sharing
Great educational video.Thanks for making it.
Did you take this from a portable ac? If yes, which one?
Thanks for the video. Did you find anything broken when you took it apart?
the small hole in the top of shaft is the "centering hole" for machining.
throttle bottle yeah. I figured it was for something like that.
Will scroll compressor get damaged if it's made to run in reverse?
Won't the vacuum side go low before the pressure side as it wears out?
Very good illustrative video !
Is That From Trane Central Air Conditioners?
This was so insane and cool
which VFD are you using?
very educative. Thank you
may be it is medium scroll type 1 , i 'm not sure but i think the motor lower bearing is in contact with the lubricants ..
Excellent tear down. 👍👍
Nor-Cal Refrigeration & H.V.A.C thanks man
hey smurf boner's dad!
Wow that is awesome! So not safe but that was great. Nice video dude
Excellent presentation....
Is this inverter?
I love VRV variable Refrigerant volume system that's why I love and like liked this video and I am HVAC technician so i loved the AC video but this one is really ossooom...✌️
Thank you for this video.very very amazing.
If it runs dry do to a leak will it recover original level of vacuum?
Compressor oil will mix with refrigerant gas?
SARAWESHWARAN BASHKARAN it will blend with the liquid refrigerant. The purpose of a crank case heater is to keep the oil warm so they don’t blend.
@@actechformallyyomama746 crankcase heater is for refrigerant migration.
Really where is it migrating to?
@@actechformallyyomama746 the coldest part of the system. That's why you have a crankcase heater is to keep the compressor warm and avoid flooded starts. Sorry and I meant refrigerant migration not oil migration.
awesome video!
Honestly it would been nice if you could given a tutorial explanation in this operation and what the parts are actually doing for us Dummies 101. Thanks.
That was cool Ulises. Did you put baseball cards in your bicycle wheels growing up?, ha ha.
polishtheturd mickelson lol 😂 thanks
That was a cool video. Good stuff. Have a good week at work, Don't let them work you too hard, lol.
cool，The video at the beginning shocked me。
How comes the lubrication oil come from the bottom of that thing to the scroll compressor in the top?
Karl-Alfred Römer their are ports for oil to run through the entire compressor to lubricate the moving parts. Oil runs through the entire refrigerant circuit.
That is cool. Eccentric oscillation.
what is the TORX screw size??? M7?
Can this compressor be fixed once burnt? just asking
is it oilfree ?
That's cool sounds like a lawn mower engine. Did you have it on a vfd
Best autopsy yet you can see how it oils that top bearing and everything!
Joe Shearer lol yeah I did. That vfd goes up to like 500 htz. I was scared to take it up to 100 htz. Almost double the rpms. I have another compressor. I might try to take it to 200 lol.
Ulises Palacios you thinkin about a scroll mod to that Honda ?
Joe Shearer lol 😂 they now have an all electric dirt bike. Alta 15 grand.
Joe Shearer yeah. That's what I wanted to see
This is cool! Thanks!
fantastic video
Nice video. Nice vfd also.
Congratulations for you
Thank you for this video.
Could one of these be used to compress air for tools?
These are used in air conditioners
Parabéns, muito bom
Did you have VFD controller here? What kind of motor controller setup did you use? Was this seized due to floodback ?
Farther down Joe Shearer prompted the original poster's reply: "Joe Shearer lol yeah I did. That vfd goes up to like 500 htz. I was scared to take it up to 100 htz. Almost double the rpms. I have another compressor. I might try to take it to 200 lol."
why would there be equalized pressure on a scroll brand new?
Unlike reciprocating compressor. On scrolls the pressures equalize in the compressor when it’s off
@@UlisesPalacios I realize that and thankyou...How bout when it is running.
looking for a scroll compressor without a built in motor.
As it ages and the system has leaked down a few times it won't build sufficient vacuum and the evap coil floods
Very cool video
Good one
Professor Al-Aziziyah, the reasons for the weariness of the mechanical part
Cool video 🤘🏾🤘🏾
Typically, what sizes of external torx do you come across when tearing this compressors apart?
Der Werkzeug König there are many different compressor. Different torque ratings for every bolt. Some are over 150lbs to as low as 4lbs.
tnks for you
very good
If it's working you can turn it into an air compressor if you have a welder and you fixed it 🤔
this is great
❤️❤️❤️❤️❤️
Informative
Compreesor not working power ok terminal ok whatis the reson
👍👍👍
Cool beans man! Don't put you eye running that thing.
Sounds just like a lawn mower engine.
#500!!!!
THANKSSSSSSSSSS
asmr
I guess your not doing HVAC anymore huh...shame
10:27 6.0 Powerstroke 😂
That's neet