Helicopters are really difficult to build from scratch! You need soo ma ny things and so many things have to perfectly align. I would say it's near impossible 😭
Fantastic design. It would also very helpful if you could specify how many from which parts need to be printed for making a gimbal. I can figure it out by trial and error, but would make life a lot easier.
@08:40 I wouldn't trust that bare Stick even without my life depending on it... Maybe consider adding a bore to thread an M3x30mm Screw all the way through it and into the Gimbal? 🤔
Trimsiz gimbalları kendim tasarlayıp basmıştım uzun zamandır kullanıyordum, trimli bir gimbal tasarımı düşünüyordum ki bu videoyu yüklemişsiniz. Şahane ötesi profesyonellikte bir proje olmuş. Ellerinize sağlık👍🏻👍🏻👍🏻
Sir, I liked your all videos and I am trying to make the same videos so make more videos as soon as early on new flying objects in detail. Thank you :)
Can you pls write a code to play fpv simulator with this joysticks using Arduino pro mini. And if I want to use it as TX, I have just switch the code. It will be amazing and so useful to everyone.
Merhaba, içerikleriniz çok faydalı. Ancak bu Joystick için hangi parçadan kaçar adet basılması gerektiğini bilemedim. Bir liste halinde yazabilir misiniz? çok yardımcı olur. Teşekkür ederim.
This one is amazing . I am not able to find these joystick anywhere now i am going to build my own joysticks please tell me what i set the size for these joystick from your files
Hi Kendin which slicer do you use and as i can see printer is creality. I have a new CR-6-SE with CURA slicer but cannot print well your STL files. Perhaps you can give me your slicer configuration. Thanks very much
I printed some parts with CR6 and others with Prusa MK3S+. I'm using Cura for CR6. The settings I use for this are Cura's "standard quality 0.2mm" settings (nozzle temp different... 210°). The filament is also important. I am using Esun PLA+.
Arduino does not control the brushless motor. It controls the brushless ESC. Brushed and brushless ESC are controlled by the same principles. No other code is required.
@@Kendin-Yap Thanks for replying Kendin but there is one more problem that in the description of the video you have written that you have used 220 degrees pot but now you have said that you have used 320 degrees pot will you please specify that which one you have used.
@@Kendin-Yap Thank you very much for supporting me. I live in India and here many of the Chinese e-commerce sites are banned that's why I am not getting 220 degree pot, will you please provide me the link of site from which I can buy other than that of chinese one. Here I have ordered 5k pot but i have not noticed that it was of 300 degrees. Will you please help me out here either by changing some code or by providing me the link of 220 or 60 pot.
Merhaba dostum. Aklımda bir proje var fakat nerden baslamaliyim bilmiyorum. Telefonlar ve tabletler için mekanik bir gamepad hayal ediyorum yön tuşları da dahil herşey mekanik olacak. Yani telefonu 8 parmak kullanabileceğimiz bir düzenek. Telefon yada tablette ekrana mekanik dokunuşlar ile karakteri yada aracı kullanabileceğimiz yapılabilir mi
Arduino joystickler yaylıdır. İlgili kumanda videosunda çıkartmadım ama gaz kolu için istersen çıkartabilirsin. Bu kullanacağın ESC nin çift yönlü mü yoksa tek yönlü mü olduğuna göre değişir.
wow i cannot believe someone did this, i was thinking about this since 2 weeks, because cheap thumbsticks have such bad range of motion about 20% of movement map to 0-100%. and 80% your finger move and does nothing its already at max.
Selam Hocam 1 tane joysticke kaç tane 0.4 ve 0.5 yay gerekiyor? (ve bunlar gaz joysticki ile aynımı yoksa 2 joystickde farklı sayıda yay mı kullanıyoruz?) cevaplarsanız sevinirim
Bu potanslar ile ilgili bir konu. Klasik potanslar ile tam hareket almak zor. Alıcı kodundaki map satırlarında ki 1000, 2000 değerlerini 700, 2300 yaparak biraz daha fazla hareket elde edebilirsiniz. Hatta bir çok model uçak için yeterli servo hareket alanın bu şekilde elde edilebilir. Bir de 0,255,1000,200 yerine 0, 255, 0, 180 yazarak deneyebilirsiniz. İdeal olan ise 60 derecelik potans kullanmaktır. Ama zor bulunuyor ve bu yüzden pahalılar.
'' multi function control unit 03 '' bu yazdığım sistemi yapabilir misiniz ? Bu sistem TR de satılmıyor ve dışarıdan sipariş üzerine alınınca çok uçuk fiyatlara maal oluyor.
Türkiye nin ilk ve tek gerçek DIY Kanalı.
I can learn to build many rc planes from this channel
So I love this channel and you.
Carry on bro
Love from 🇮🇳 India
Please make a rc helicopter
Me too
Helicopters are really difficult to build from scratch! You need soo ma ny things and so many things have to perfectly align. I would say it's near impossible 😭
Yeah but its a little bit tough
Up
@@_namenloses_4593 it is possible if you try bro
Such a wonderful creation. You deserve more bro!
I just made a multi-function remote control, refer to your diy video, but I have added a lot of functions, and I may need this device now. Thank you!
You became my favourite youtuber
You made rc transmitters are beautiful
Thank you very much for sharing this excellent work. It's great.
Fantastic design. It would also very helpful if you could specify how many from which parts need to be printed for making a gimbal. I can figure it out by trial and error, but would make life a lot easier.
Pls help me i also want to make a radio control er like this pls reply
I watched it twice its very nice. I need single axis for my project but it's tempting to print this beauty
WOOOWWwww that's neat!
and also open sorce? respect!
Healthy and friendly greetings from the Netherlands!
Rob
the print quality is insanely good.
@08:40 I wouldn't trust that bare Stick even without my life depending on it... Maybe consider adding a bore to thread an M3x30mm Screw all the way through it and into the Gimbal? 🤔
i wish i found this channel earlier ! 🤩
Trimsiz gimbalları kendim tasarlayıp basmıştım uzun zamandır kullanıyordum, trimli bir gimbal tasarımı düşünüyordum ki bu videoyu yüklemişsiniz. Şahane ötesi profesyonellikte bir proje olmuş. Ellerinize sağlık👍🏻👍🏻👍🏻
Where I can buy foam board in India offline market
Please reply
Bravo çok güzel olmuş. Güzel bir 3d projesi olmuş.
Please give the STL files link in description to make the parts
I added the STL link below the video
@@Kendin-Yap no se puede descargar
how to make a digital soldering iron station by 'arduino nano' please make it.
Please make a transmitter design with these
Sir, I liked your all videos and I am trying to make the same videos so make more videos as soon as early on new flying objects in detail. Thank you :)
Ellerine sağlık adamın Dibisin ❤️
Çok yaratıcı ve çok güzel olmuş
Elinize sağlık hocam. Modellerin STL dosyalarını paylaşma imkanınız var mı?
Teşekkürler. Videonun altına biraz önce linki ekledim.
Hi if possible can you help me to make a drone transmitter for my phone's simulation
muito top mano. Aprendo muito com você !!!
Such a wonderful job.
Is the first demonstration with solid works?
This should get more and views, very interesting and learnable video
You videos are super
Prima arbeit, sieht einfach gut aus
❤❤❤I like drone remove
Nice 😍😍😍😍 very beautiful 😍😍❤
Beautiful video
Sonunda istedimi birinci video yu yapmisin cok guzell olmuss
Great job!!!! Thumbs up
Awsome work!
Can you please give us the edited code with the changed value?
Can you please add it to the discription?
Can you pls write a code to play fpv simulator with this joysticks using Arduino pro mini. And if I want to use it as TX, I have just switch the code.
It will be amazing and so useful to everyone.
Please Make Ornithopter Step By Step ,Ttransmitter and Receiver make kit.
Awesome 👏👏👏👏
Very cool 👍
Tebrikler güzel çalışma. Bunu birde tam kumanda haline getirip süslerseniz harika olur
Muito Bom isso. São gênios!!
Muito Obrigado por compartilhar !!!
Hello. How can I add a snapback system where the controls stay in the center when I release them. Like how RC transmitter joysticks do
ha dude.....plz make a video on how to mix channels on this transmitter and receiver for a RC helicopter
You are so Cool~~ l like it!
Kanal çok kaliteli
superb sir
Merhaba, içerikleriniz çok faydalı. Ancak bu Joystick için hangi parçadan kaçar adet basılması gerektiğini bilemedim. Bir liste halinde yazabilir misiniz? çok yardımcı olur. Teşekkür ederim.
Bunu yapalı çok zaman geçti. Detayları hatırlamıyorum ama bir kol için trim kolu parçası 2 adet diğer parçalar birer adet olması lazım.
This one is amazing . I am not able to find these joystick anywhere now i am going to build my own joysticks please tell me what i set the size for these joystick from your files
Dimensions are approximately the same as a standard RC gimbal. And it is fixed.
Sir where did we get the potential metre?
can you please deliver it to my home? very very nice project bro
can we use plastic sheet instead 3d printing
benzersiz güzel bir çalışma tebrikler
Hi Kendin which slicer do you use and as i can see printer is creality. I have a new CR-6-SE with CURA slicer but cannot print well your STL files. Perhaps you can give me your slicer configuration. Thanks very much
I printed some parts with CR6 and others with Prusa MK3S+. I'm using Cura for CR6. The settings I use for this are Cura's "standard quality 0.2mm" settings (nozzle temp different... 210°). The filament is also important. I am using Esun PLA+.
@@Kendin-Yap Thank you very much
Can you make a plane that fly like a month and make auto pilot for it to please.
Can you make trimmer with push button?
great job !! Which is the black filament ? thank you
Thanks. Filament is Prusa Galaxy Black
un grand merci a toi, great job
Tebrik ederim çok iyi olmuş. Gergi yaylarını nereden temin ettin?
www.promodelhobby.com/urun/cift-kancali-cekme-yay-0-5x4x14-mm-4-adet
www.promodelhobby.com/urun/cift-kancali-cekme-yay-0-4x4x14-mm-4-adet
Is there a model without Trim !?
Please make a rc car gyro
Have you have easy steps to make it
Awesome
Unfortunately I can push like button only one time!!!!
Very nice. Good video.
Hi bro perfect. Cannot find 5k potentiometer. Can I use 10k??? Thanks very much. Anthony
Thanks.. 10K is not ideal, but usable.
@@Kendin-Yap Thanks very much. Also i have got ZERO stls and have made the 6ch tx/rx.Perfect!!!!!!!
RC arazi aracı yapar mısın?
Şimdi birde 3D yazıcı lazım. Eline sağlık usta....
Please make a rc Submarine
Please make this type joystick module with out 3d printer
You know what to make good 👍
Please make flysky i6 transmitter
Pls make cardbord version of this pls
esto sirve para jugar videojuegos arcade?
Please make diy osprey
How did you control the brushless motor with orduino nano?? Can you show me the code??
Arduino does not control the brushless motor. It controls the brushless ESC. Brushed and brushless ESC are controlled by the same principles. No other code is required.
@@Kendin-Yap how to do esc calibration with orduino nano??
Acaba parçaların tasarım dosyalarına ulaşabilir miyim? Step formatında ya da bir cad uygulamasında rahatça düzenleme yapabileceğim bir formatta.
Can I use 10k pot please reply fast
I need you to do "motor grider" please please please help
Request for tutorial How to make F117 sir. Thanks
This is lit... 🔥🔥
Use stm 32 instead of Arduino nano because it is more faster than Arduino and ha great storage than Arduino nano
You earned 1more subscriber . is this open source project ?? Thank you
Thanks. Yes this is open source project.
MÜKEMMELSİNİZ
Bro. I need this print file i want the print but i can't drawing this make, Can you provide the print file
Please check below the video. Link available.
Click "more" or "more info"
You can use 5k potentiometer I can use 10k potentiometer its working or not please tell me
It has to be 5K. 10K will work but the signal limit will be different.
OK sir but its working or not 10k potentiometer is good or not please reply
@@bagavathi9428 not good
Tek kelimeyle mükkemmellllll
Hello, kendin i am making the joystick but i am not getting 5k pot of 60 degree or 220 degree I am getting it of 300 degree rotation, now what to do?
The ones I use in the video are also standard pots. (320 degrees). And the code is for standard pots.
@@Kendin-Yap Thanks for replying Kendin but there is one more problem that in the description of the video you have written that you have used 220 degrees pot but now you have said that you have used 320 degrees pot will you please specify that which one you have used.
@@anuragsen3694 Sorry.. 320 is a typo. 220 is the correct one. And this is the standard pot value. Pots sold in general are of this value.
@@Kendin-Yap Thank you very much for supporting me.
I live in India and here many of the Chinese e-commerce sites are banned that's why I am not getting 220 degree pot, will you please provide me the link of site from which I can buy other than that of chinese one. Here I have ordered 5k pot but i have not noticed that it was of 300 degrees. Will you please help me out here either by changing some code or by providing me the link of 220 or 60 pot.
@@anuragsen3694 www.amazon.com/HiLetgo-Single-Joint-Potentiometer-Variable-Resistors/dp/B00N1ZIXKA/ref=sr_1_1_sspa?dchild=1&keywords=5k%2Bpotentiometer&qid=1630400507&sr=8-1-spons&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUFSQjI5QU84WjBFOEImZW5jcnlwdGVkSWQ9QTA1NTA3OTM0UlpCNEExRUswQ0smZW5jcnlwdGVkQWRJZD1BMDk3NTY1MTNWRjdJNjRSOU1MQUgmd2lkZ2V0TmFtZT1zcF9hdGYmYWN0aW9uPWNsaWNrUmVkaXJlY3QmZG9Ob3RMb2dDbGljaz10cnVl&th=1
Merhaba dostum. Aklımda bir proje var fakat nerden baslamaliyim bilmiyorum. Telefonlar ve tabletler için mekanik bir gamepad hayal ediyorum yön tuşları da dahil herşey mekanik olacak. Yani telefonu 8 parmak kullanabileceğimiz bir düzenek. Telefon yada tablette ekrana mekanik dokunuşlar ile karakteri yada aracı kullanabileceğimiz yapılabilir mi
Ben de kumanda yapmak için iki tane satın aldım bir tanesinen yayını çıkartmam gerekiyor mu çünkü bıraktığım yerde durmuyor hep ortada
Arduino joystickler yaylıdır. İlgili kumanda videosunda çıkartmadım ama gaz kolu için istersen çıkartabilirsin. Bu kullanacağın ESC nin çift yönlü mü yoksa tek yönlü mü olduğuna göre değişir.
Glue used?
Thanks in advance
Yes for some parts.
(Super CA Glue with Spray Adhesive Activator)
wow i cannot believe someone did this, i was thinking about this since 2 weeks, because cheap thumbsticks have such bad range of motion about 20% of movement map to 0-100%. and 80% your finger move and does nothing its already at max.
Selam Hocam 1 tane joysticke kaç tane 0.4 ve 0.5 yay gerekiyor? (ve bunlar gaz joysticki ile aynımı yoksa 2 joystickde farklı sayıda yay mı kullanıyoruz?) cevaplarsanız sevinirim
Gaz kolunda yay olmadığı için sol kolda bir tane. Diğer kolda 2 tane
@@Kendin-Yap Teşekkürler
How can I contact you?
Hocam yazılım kısmın da değişiklik yaptım ama servoların bazıları ya hiç dönmüyor ya da çok az dönüyor hatayı nerede yaptım acaba ?
Bu potanslar ile ilgili bir konu. Klasik potanslar ile tam hareket almak zor. Alıcı kodundaki map satırlarında ki 1000, 2000 değerlerini 700, 2300 yaparak biraz daha fazla hareket elde edebilirsiniz. Hatta bir çok model uçak için yeterli servo hareket alanın bu şekilde elde edilebilir. Bir de 0,255,1000,200 yerine 0, 255, 0, 180 yazarak deneyebilirsiniz. İdeal olan ise 60 derecelik potans kullanmaktır. Ama zor bulunuyor ve bu yüzden pahalılar.
@@Kendin-Yap çok teşekkür ederim 🙏
weight?
how much infill did you use?
0.2 layer printed with standard settings. (infill 20)
@@Kendin-Yapcan i use normal pla filament? I have either PLA , ePLA or ABS filament
'' multi function control unit 03 '' bu yazdığım sistemi yapabilir misiniz ? Bu sistem TR de satılmıyor ve dışarıdan sipariş üzerine alınınca çok uçuk fiyatlara maal oluyor.
Please make a biocopter