How To Fix Laptop Computer Motherboard Ribbon Cable Clip Fastener Tutorial
Вставка
- Опубліковано 22 сер 2024
- Ribbon Cables on computer Motherboards are usually held in place by a Retainer Clip. These clips are very easily broken and are almost impossible to find for sale. Often, you have to purchase a used or 'as is' Motherboard to get the clip. Even if you can find them, they are very easy to break when your installing it as well. This video will show you how to safely remove one and then how to install it onto your Motherboard safely. Without this clip, you often have to resort to electrical tape or some other means of fastening down the Ribbon Cable which is not ideal and can lead to the Cable easily coming loose. Feel free to comment or ask questions !! Please remember to 'Like' if this was helpful :)
Computer Repair Tools & Supplies: www.amazon.com...
Thanks for watching! Please consider subscribing to my new channel here: www.youtube.com/@jamminpcs.
I'm trying to move the easier hardware stuff there so that I can focus on the more in depth troubleshooting and diagnostic videos here :)
Alternate fix: The ribbon that gets clipped in has two sides, one with exposed connections and one covered in plastic. Cut a piece of electrical tape and stick it to the end of plastic side. This will give it just enough thickness to make the connection and hold it in place. If you're worried about it working loose you can either tape it down or put a bit of hot glue on it (the glue is not conductive, and easy to peel off)
The electrical tape suggestion worked for my situation where the black piece was fine but the white base was cracked. The connection was not tight but after adding the electrical tape on the ribbon cable and then giving it a solid push into the connector, the connection was tight enough to work again. Thanks for the tip!
Can't thank you enough for this tip. CHEERS!!!
I will try this thanks.
my man, you saved me!!!
@@user53473 Glad to help. That tape tricked saved me as well.
a thousand dollar laptop relying on a super thin plastic"wall" 1mm in length.freakin ridiculous.
Ya that stinks :( Hopefully you'll be able to find a replacement. If not, try purchasing a used or bad motherboard and taking one off of there :)
Stupidity at it's best.
My neighbor asked for my help. I had an old SSD drive and decided to install it in her laptop. Somehow I pulled the latch for the keyboard ribbon cable out. After 2 hours of fighting with it I looked up solutions on youtube. This video saved me. thanks!
This is exactly the type of tutorial I needed. Bought a Nintendo switch motherboard and the display connector had a pin out of alignment (fixed that) but the ribbon cable is damaged and the connector doesn’t have a clip, so I’ve bought new connectors to salvage the clips from them and this is what I’ll be watching whilst doing that! Thanks :)
Happy to help :) Always here if needed !!
How do i know if a pin is out of alignment
@@Mars4O4 You have to just look. They are small. You may need to use a magnifying glass to make it easier to see :)
Sorry but This is my last question the nintendo switch screen ribbon cable refuses to enter, could this also be a sign of bent pins?
@@Mars4O4 You will be able to see if the pins are bent. If it looks and feels flat then most likely, no pins are bent. It can take a few tries to get it in if your not used to it.
this helped me put back2 clip retainers of a customer laptop and avoid me go to a computer repair shop, thanks a lot
Happy to help :) Always here if needed !!
Just what I needed. Other videos were missing the clarity and video quality to understand what to do. You saved my butt... Thank you!!
Happy to help :) Always here if needed !!
Great video! One advise, i struggled too with positioning the clip @4:35
So i placed a (credit)card against the holder of the clip in front of it, then it has the right height for the clip to position it. That way it was very easy to clip it in. Hope it helps some.
And thanks, it saved my keyboard connecter in my laptop!
I never would have thought of that! Thanks for the info :)
You sir are a godsend and a life saver. I had a keyboard ribbon cable clip fall out while trying to reconnect the keyboard on an old Asus F501A laptop. Thank you so much!
Glad your all set :) Always here if needed !!
Four years ago I broke the retainer clip for the mouse trackpad, been using a seperate mouse, a few days ago I was lucky to find the same laptop for rubbish, I found and followed your video and I managed to repair the retainer clip, good idea about breaking the walls first, wanted to say thanks
Great to hear !! Always here to help :):)
Thanks for this very helpful video. I had given up on repairing the cable clip until I came across this.
Happy to help :) Always here if needed !!
Thank you sir you saved my laptop but i didn't buy a motherboard but i just some how un pluged the lock from its place but i kept it very safely after 7 months i thought to repair the laptop on my own and i remembered that i broked it months back so serched on you and you came and the rest is history 😂😂😘❤️
Happy to help :) Always here if needed !!
Thank you for mentioning that some clips attach differently. hearing that, I got out my botany hand glass and looked at my clip, and saw that unlike the ones you illustrated, mine is actually attached at each contact pointnot out at the edges.
The metal of each contact forms a tight C shape, as viewed from the side, with the clip swinging like a gate in the top part of the four Cs and the flat ribbon inserting below the gate with the lower part of the C shape making contact with the underside of the ribbon. So all I had to do was reinsert my gate into the C's that I had pulled it out of before I understood that there was a latching mechanism here. It wasn't trivial because I had to get the angle right and I had to bring just the right amount of force to bear on a tiny little thing.
Glad your all set :) Always here if needed !!
Thanks you save my cable clip, others showed the white part releases the ribbon , but mine like yours was the black part that releases the cable, tricky for sure
Happy to help :) Thanks for the nice comment and the like !!
@@PC_Monkey whats the white thingy on the clip ? I broke those thing
@@ThePASBERUK I think your talking about the port itself that is attached to the motherboard. If that is broken then there is a good chance that the ribbon cannot securely connect. You would need a replacement motherboard :(
Or buy and reflow just the connector. It's sell separately, not a big deal but it's not a pleasent job for sure.
Rr
Thanks for the video, i tough i broke the tab but after watching the video i understood how i had to reinstall it correctly. Saved me some good $$
Thanks !
Great to hear !! Always here to help :):)
NGL just watched this video and I've just been saved
Glad your all set :) Always here if needed !!
Thanks. I took this off by accident since I thought the ribbon broke off of it and tried to put it together. Didn't realize it just clipped in place.
Happy to help :) Always here if needed !!
Mine came out with the cables older laptop and all and they clipped back in once you showed me the correct orientation thank you very much
Happy to help :) Always here if needed !!
The big ones are easy but do you have a video with installing to small clip?
It would be the same operation just with a smaller clip. No, sorry I dont have a video for that.
Awesome! Thanks man!
Just got a laptop repair in today where a different tech busted one of these... he also managed to lose all of the original screws.
LOL I remember those days. Glad this helped :)
This has given me hope to fix my N3dsxl, thank you so much
Happy to help :) Let me know how it goes !!
i also broke a clip, do you know what other things i can do to fix it?
Hi, I met the same issue with u. Do u fix ur retain clips successfully?
@@silencedspec1711 no, i lost the piece inside of my 3ds and when i actually went back to fix it, the piece was missing
That’s exactly the video I need! Thanks
Great to hear !! Always here to help :):) Also, feel free to follow my other channel that I'm starting that will offer computer operation tips and general tech tips !! www.youtube.com/@JamTechTips
Wish you've shown installing the small clip, great video anyway I'm having trouble installing a small clip like this
These are very frustrating. High risk of breaking the clip or the port :(
Worked like a charm! Thank you for your efforts! Use tweezers and a magnifying glass to make it easier for small clips like mine, which I would have never fixed without this video
Happy to help :) Always here if needed !!
You saved my computer, thank you!!!
Happy to help :) Always here if needed !!
Very useful. Thankyou
Great to hear !! Always here to help :):)
OMG! This is what im looking for!! Thank you so much😄😄
Happy to help :) Always here if needed !!
Can you fix mine ? Samsung Galaxy tab 2 10.1 p5113 my clip went flying across the room with a small touch. I tiried tape and it semi worked but the screen now is nonresponsive. Touch screen doesnt work any more. I tried fix it for parts they want $19.99 for motherboard but out of stock. I tried making a clip out of old credit card. I tried a plastic peace from a bread package that holds the bread close. But it curled up tape works but screen unresponsive anymore.
Oh and I went through about 7 different videos before coming across your type connector which is like mine
Glad we did it then :):)
thanks, that saved my new motherboard.
Glad your all set :) Always here if needed !!
great video. very precise and enjoyable. no annoying music lol.
i broke a 55 pin display connector on a moto z2 play phone. i was using my pinky finger as was told online, (instead of a screwdriver). but it split in two.
maybe a plastic spunger would be a better choice from now on lol
im based in northern ireland, but could only order connectors from the united states.
so fingers crossed in 2 weeks, i can migrate the clip onto the old mobo
Yes, I try not to try and make a DIY computer tutorial 'entertaining' lol. Its just info :)
Good luck !! Let me know how it goes :)
Great video. picture this: the ribbon cable from a laptop power switch. one end of the cable is soldered to the power switch board and the other end goes to a connector on the motherboard. The cable goes into the connector but instead of a locking bar this connector keeps the cable in with a part that pushes down on the connector and cable to keep the cable in. Do you know what the name of this connector is called? thanks
I am have done this by pulling it out. it works
Glad your all set :) Always here if needed !!
Thanks for the video ! How can I fix a connector with broken walls ?
If the walls are broken you would have to remove that port and solder on a new one. If that isnt an option, then you would need to replace the board itself
@@PC_Monkey I thought so. Thank you for your prompt reply :)
Thank you so much! Lifesaver! ☺🖖
New sub as well! ;)
Thanks !! Glad this video was helpful :):)
are there any videos how to change not this rotating latch type but the sliding "drawer" type ?
mine is deferent the clip is inside, how can i attach photo, thank you
Thank You!
Your welcome !! Happy to help :)
The same trick can repair a little fpc clip? Thanks from Spain!
Glad your all set :) Always here if needed !!
How about the small clip I'm having trouble on installing it
You can see how to install it here. What part are you having trouble with?
Thank you so much sir
Your welcome !! Happy to help :)
Thanks man! That was a fantastic little tip!
Happy to help :) Always here if needed !!
Thanks for sharing
Your welcome !! Happy to help :)
Wish I’d had this info a few years ago.
How difficult would it be to replace the port itself? I really destroyed my palm rest cable port (and the gold connectors) on a x230. Of course, the laptop remains usable, just no track pad now.
That would involve soldering the new one on. Not the easiest thing to do but as long as you dont damage the motherboard in the process, theres really nothing to loose as its unusable anyway
@@PC_Monkey Thanks. Will just let it be then, as your method allowed me to unlock and enable bluetooth (and my mouse) on the laptop.
Hi I just upgraded the SSD on a HP Elitebook 8560w in post 1 and in process broke the "smart card reader door" connector to the MB - it is just 4 pin wide but a nuisance. Do you have any suggestions?
Video looks great -
If it broke, you would have to replace it. I usually get most of my parts on sites like Ebay, Amazon, etc
What if I take chose clips from a good motherboard..just like u said carefully.... Will that affect the motherboard in anyway.... Please let me know thank u
No :) They are a non-electrical component. Its wont affect anything :)
@@PC_Monkey thank for ur reply..... I will try this now... But i m afraid like hell
@@arjunpurty6590 Good luck !! Let me know how it goes :)
@@PC_Monkey i dont wana be annoying sir but are u 100%sure if break the walls of those FPC connector it won't damage the good motherboard......coz I m about to do this in a working laptop and i am scared that i will damage the motherboard or something
@@PC_Monkey I swere this is the last question... I need one last confirmation before I attempt this operation
The little clip broke off. Can I send my laptop to you for repair?
Sorry no. You would most likely have to replace the motherboard then if you cannot find the clip for sale.
Hi !
English is not my mother language and I’m looking for one of those clip !
Where can I buy it ? what is the exact name of this spare part ?
Thanks a lot !!
Can the latch part be replaced? The piece that flips up & down and locks the ribbon in place is broken.
Yes, you can replace the clip. You can try to find them for sale on sites like Ebay, Amazon, etc. However, many times, you wont find them for sale :( The next best option would be to find a broken or 'as-is' replacement for your motherboard that you can buy cheap and take the clip off there
If you have broken the cable clip, can you tape down the ribbon?
Yes. With electrical tape preferably. However, its not a very good solution. It can still come up.
Hi I have an Acer projector, it stopped working via on/off buttons and remote I removed the top and noticed zif connection to top has snapped in half due to heat I presume nothing wrong with projector apart from this
Unlikely to find a replacement?
If physical damage happened due to overheating, your most likely looking at needing a replacement. Is this a board of some kind? Sorry, I dont understand zif connection.
In case if I don't have the clip, can I use something like any kind of tape to hold it down?
Thanks in advance!
You can try to use tape but its no where near as secure as the clip :( The ribbon cable will find it easier to come out :(
Nice if you can show me one for a cable clip that’s the size of a small black ant. For a lap top fan would love to see how to put it back on
If its the same style then its the same as seen here. Just because its smaller, doesn't change how its handled. If its a different style, what brand and model computer do you have so I can try to see what your looking at?
I owe you my life
Happy to help :) Always here if needed !!
Any suggestions,.. Where can i get small retainer clip for Thinkpad x220T. This one connects trackpad belt to board
I usually get most of my parts on sites like Ebay, Amazon, etc. However, these parts can be hard to find. If you cant find it, you may have to purchase a 'as is' or bad motherboard and take the part off of there.
Need to replace the complete ribbon cable pins , do you have a video how to unsolder pins ,
No sorry. I dont have any solder videos on here as of yet :(
Hi,
I watched this video. But it wasn't helpful because, in my situation, and I think for most, it isn't the clip itself it breaks or it doesn't break alone. Rather, the piece holding the clip which is on the motherboard breaks. Just as you pointed out that the clip is fragile, so are the sides and if the clip breaks out of the sides, usually one or both of the sides do also. The question is, how can you replace that? How can you replace that rectangular frame that the clip holds onto?
This video shows how to replace a clip as its the only thing most people can do with limited skills. If the port breaks, then like most motherboard ports, its not easily fixable. It would need to be removed from the board and replaced or the board itself would need to be replaced.
So here's an adjacent question: I was tearing down a Stadia controller, and the front of the cable is connected to the rear with a ribbon cable. I tried to open the clip to remove the ribbon cable, and the entire clip came off, both the white and black parts. Is that repairable? If not the controller is trash, but I'd really like to save it. Any help is greatly appreciated!
Its repairable if your able to solder it back on or solder on a new one and source one from somewhere. Honestly its been ages since I tried purchasing one so I dont have much help to offer about where to get one.
you are a savior thank you
Happy to help :) Always here if needed !!
Hi nice video. But if you can not find clip. Then what can be done with ribbon cable so that current flow. Waiting for answer
You can try using a small piece of electrical tape but there really is no good solution to not having that component :(
my brother from another mother....board haha
Any idea how to get the ribbon to stay in place when you can't find one. I was hoping to use tape or glue some how to keep it in place. Laptop still usable but the cable connected touchpad but now I use a mouse.
Sometimes if I have to, I have used a small bit of electrical tape. But the best way is to replace the component if its damaged or breaks
My issue is the Ribbon cable won't go inside the connector the flaps are fine and it opens and closes fine but it just won't insert anymore ... the cable was badly damaged so I'm replacing the cable and hopefully it works if not I'm just hoping I can replace the whole piece it docks into
Yes, if the ribbon cable is too badly damaged, it may not correctly enter the port anymore. Good luck !!
The new main board I bought for my tv didn't come with the clip. I'm not sure if the main board is the problem yet. Is there a way to swap it without breaking the walls off of the original connector?
You can try to bend it out, but I usually break them 50% of the time doing that lol :(:(
@@PC_Monkey thanks for the reply, I'll give it a shot. Also thanks for the video, exactly what I needed to know. Keep up the great work!
@@jonathanbroczkowski3804 Thanks !! Good luck :)
How do u repair if that whole ivory piece broke off?
If the whole ivory piece broke off then you cant really fix it :( You would need to solder a new port onto the motherboard or replace the motherboard :(
Will the connection work without the clip?
Yes, the ribbon cable will still sit in the port fine. However, it will be very easy for it to fall out. You can try using electrical tape or something else to hold it in if you have lost the clip
Nice video but how to you get the black part off the broken port you're trying to repair? Thanks, Dave
This video does not show how to repair a broken port. It shows how to remove a clip and install a clip
In my case the white connector thing itself has come out.
That most likely means you need a new motherboard :(
My 40-pin Zif cable locking device has told me to `go pound sand` 1/10th of a thousand times.
Nice vid and I learn a lot but it seems like this would only be useful if you have a donor board as not all connector size is same..
Yes, in order to replace a clip, you would need a replacement of the same size lol.
Thank you bro. 😉
Happy to help :) Always here if needed !!
I used this video and got my keyboard ribbon cable back in place. Thanks PCM! However, not all the keys work unless I put pressure on top of the clip. I tried a tip from PenguinSavage here and put a piece of electrical tape on but then the clip won't stay closed. I tried taping it down. I folded up layers of tape (to make a lump) and taped *that* down hoping that when the keyboard was in place it would put the necessary pressure on. No go. Any ideas? It's an old laptop that I'm fixing up to have as backup, so I'm not worried about trying things.
Most of the time, if this clip is broken, it needs to be replaced. There are very few ways of securing it properly without a working clip.
@@PC_Monkey Yeah I'm getting that. Just hoping for a 'creative' solution. Thanks for your reply though.
@@danoconnell1833 Good luck !! Let me know how it goes :)
Thanks a lot lot the great video!
However, I have a question ; what if the two 'little walls' on my motherboard broke - meaning if ill place a new retaining clip it wouldn't fasten.
do you have a solution to resolve this problem?
Thanks again!
Then the port itself is damaged. Depending on your comfortability with soldering and the availability of parts, you can try to replace the port. Most of the time, that means you need a new board though :(
@@PC_Monkey I have no problem with soldering, however I don't see how that's possible since we are talking about plastic (retaining clips)
Thanks a lot
cool vid! like the slight NY/New England accent. When I needed to replace my SSD cable the retaining clip somehow popped off. no indication of damage though. doesn't like quite like yours, and the other piece actually moves a little on the MoBo. can I send a pic?
Ya, I grew up in Maine and now live in NH lol
Feel free to upload your own video and message me back here when you do. I can then view and advise further :)
Hello , thanks for the video démonstration, can i buy a ffc connector and take the clip from . Is it possible ?.
If you can safely remove the clip without breaking it then yes :)
@@PC_Monkey thanks for the answer cause i just bought some , i'll try it , and let you guys know !
@@redatheripper Good luck !!
Hi :) Swapping out a hard drive the sidewalls of the cable clip broke. Any suggestions on fixing this? Thanks.
If it broke, you would either have to replace it or replace the board. Usually, most people do not have the equipment or skills to replace the clip port so replacing the board is the only real option
@@PC_Monkey Thanks. :-) I found a video here titled "Simple Hack To Clamp Down A Ribbon Cable Connector With a Missing Clamp When Repairing a Laptop" that I'll try. Describes how to tape it down and maybe hot glue it down. Just bought a hot glue gun on Amazon arriving tomorrow. I'll see how it goes. It's a nice laptop. About $1K laptop with a 17.3" touch screen and nice components. I mainly use an M1 Mac Mini now but want to use Windows for some things and Parallels doesn't work that great and is expensive. Thanks for your help.
where can you buy replacement ribbon cable clips
I usually search for them on sites like Ebay, Amazon, etc. If I cant find them, which is often the case, I then try to find an 'as-is' or bad motherboard matching the one I have. Then I take it off there.
where can i buy the clip container? mine broke
I usually get most of my computer parts on sites like Ebay, Amazon, etc. If you cant find them, you may have to purchase an 'as is' / bad motherboard and take it off there.
What if the clip got broken? Is there some solution?
If any component breaks, you would have to replace it. You can sometimes find them on sites like Ebay, Amazon, etc. If not, you may have to buy a used or bad / 'as is' motherboard and take it off there for use on yours.
I have the same issue but with tablet ....my lcd screen has detached from the IC with the ribbon cable coming off the connection in ic due to the broken clamp @Pc_monkey what do i do ?
You would have to replace the broken clamp as seen here
alright, I have been through a handful of videos but can't find one on replacing the ribbon connector itself...
You would have to desolder that from the motherboard and solder on a new one. Usually more of a pain then its worth. Also, on printed circuit boards, which most are these days, thats not a very effective operation anyway
I have an acer aspire 5733z that I’m trying to fix. Touchpad motherboard clip broke and I got a dupe motherboard to swap out the clip. Only thing is the clip won’t go in without a fight and I don’t want to break another one.
Ya, thats always the trick :( Getting it back in. I have found that the best way is to approach it by laying the clip down in front of the port and trying to slide it in that way. Sometimes, you have to get one end in first and then jiggle the other end until it goes in. Not an easy task by any means. I broke sooooo many when I started doing that :(:(
Any links where I can get the clip online?
I usually try Ebay, Amazon, etc. By your make and model. Would you like help finding one?
My question is how do you do this for a Switch Joycon? I accidentally knocked one off while trying to make a repair and have been struggling for like an hour. Thanks!
Im not sure what a Switch Joycon is.
@@PC_Monkey it's a for a game console, the Nintendo switch
@@KeaneCabrera The ribbon cable ports dont look like this?
@@PC_Monkey it's that they're much smaller, making difficult to put the clamp back on.
But they do look like this
What if the white part broke off the mother board all together?
Then you would need a new motherboard. Replacing that part is almost impossible for most DIY users.
Idk if you will reply but I broke the metal lines inside the clip that holds the ribbon
Then the port is broken. You most likely need a new motherboard at this point unless its worth it to get the motherboard repaired. It can sometimes be more expensive though then just purchasing a used board on ebay
@@PC_Monkey thank you so much for replying appreciate it
@@halimahussein5591 Happy to help :) Always here if needed !!
I'm stuck trying to fix one where u push the black clamp horizontally
Those can be a real pain. Did it break? Are you trying to install a new clip or just trying to figure out how to use it?
@@PC_Monkey well the white was coming off in fragments but I put plastic to apply pressure, but I think I folded the strip too many times from trying to push it in. So I'm done all around need a new strip if that don't work idk
You didn't show how to insert the small clip.
It would be the same way you insert a large clip. Just with a smaller component :)
What if the black lock mechanism is broken?
Then you will have to replace it. Sometimes you can find them for sale on sites like Ebay. Usually, you may not be able to find them and you will have to purchase a motherboard and take it off there.
dose this relly work i need to know
No it doesnt really work lol. The video is just a really good animation ;)
How to find the plastic piece?
How do you fix it? If its broken, you cant fix it. You would need to replace it.
How do you straighten the anchor pins before you re-seat the locking clip?
OOO good question. Ive never had to do that before. When I need to straighten pins on a CPU chip, I prefer a small flat head screwdriver. So I would recommend that or a very small pair of needle nose pliers. Hope that helps :)
@@PC_Monkey
Hi, I have a Lenovo ThinbkPad T570 motherboard with the locking cilp of the hard drive conenctor broken off. I actually bought the connector and tried to take the locking clip out. The troubles I am facing is two folds: 1) some of the metal hooks of the connector holding the clip are bent or borken off; 2) the connector doens't have the walls on bothsides to take out (not like in your videos). I figure I have to open the clip in an angle to take the clip out. I ended up breaking two connectors without success. I have one left so far. PLease help. The connector is FH55-40S-0.5SH. Thanks, Josh
@@neverwasthere Prob best to buy another one at this point. Hard drive connectors are usually pretty cheap. Well under $15 USD usually
@@PC_Monkey I am talking about hard drive connector on the motherboard. Not the hard drive cable. It looks like the keyboard connector on the motherboard now.
Here is the link to the photo showing the hard drive connector on the motherboard on Lenovo ThinkPad T570 ot P51S.
forums.lenovo.com/t5/ThinkPad-P-and-W-Series-Mobile/p51s-sata-mobo-connector-is-broken/td-p/4030539
what if you need the white piece?
This video shows how to salvage a clip from another motherboard and how to install it to a motherboard. I dont understand your question.
@@PC_Monkey so basically i would need a saulter gun
But what should I do if I also broke the walls?
You would most likely have to replace the motherboard as most places will charge the same to repair the board as they will to replace it.
@@PC_Monkey thanks for answering!
@@GB-qx6si Happy to help :) Always here if needed !!
Not so easy with the small clip
Yes. Smaller is always harder
I’m tired of UA-cam ads
The white clip part itself?
I dont understand your question
@@PC_Monkey The white clip part itself. The flipper part hat secures the ribbon into place. Can that be replaced? That top of it on mine broke off.
@@grny28 If the Ribbon Cable port came off the motherboard, you would most likely have to solder a new one onto the motherboard :(
@@PC_Monkey Thank you so much...think I need to search for a used mother board for parts.
@@grny28 Good luck !! Let me know how it goes :)
finally !!
Happy to help :) Always here if needed !!
My fingers are to thic for some of these small ones, guess I’m not using my mouse lol
So uh. I didn't break the clip but I did pull it off the motherboard entirely.
Then can you reinstall it as seen here?
No we have to solder it back on.
@@InvalidUser18 Oh im sorry I misunderstood. Yes, if the port itself would have to be soldered back on. Or a new motherboard would have to be purchased.
@@PC_Monkey that's the thing. It's a custom motherboard so we can't just go buy a new one. And we don't have that much money.