I purchased these a few days ago after watching this video. I just got done installing them, and this video made it super easy. They look awesome! Thanks!
Need to add. Comments I have received and I actually agree with. "Those are the weakest looking amber lights of any on the road." "They look like lines and do not fill the entire glass area." Weak looking; dude get some real lights." Yes, they look good when installed and on. However, I would not purchase them again. Main reason was they mount from the inside out vs. others mouth from the outside in and rely on a friction fit to remain. And that does not work in all car washes. These are more secure; just too bad they did not invest in a more "fulfilling light." Some install notations.... Ended up installing the fuse to fuse 45, 10A located on the other end of that short row of fuses from the ABS module used in this video. It is immediately under the 15A (blue) fuse at the other end of the row. (You can see the blue 15A when he is plugging in the fuse at 15:21. This fuse is hot when the ignition is ON or START. And the fuse holder fits better. (I would add a photo but not sure how to post to this comment!) On my '23 there are a total of five T15 torx screws that need to be removed. Two torx screws on each side. Inner is for the plastic cover, outer may just be for the grill. However, I removed the two on each side just in case; not that hard. Also there is another torx screw in the middle just to the right of the hood latch; looking at it from the front of the vehicle. Forget those tiny tie straps. I used 3.5" black straps and they were hard enough to get locked; cannot imagine trying to use the small ones that came with the kit; at least after the lights were installed. Even though I did NOT remove the grill, it was a pain to align back up with all the locator locking pins and it appears both sides need to be pushed in at the same time. Or at least that is what I found on my vehicle. Also those six push pins, along with where that plastic cover attaches to the grill really hold that grill in place more than the side pins. Overall, not a hard install if you have all the right tools. At least you can do it all standing up.
I installed this today on my 2023 P4X. It was easy, however I did one thing different, I removed the shutter assembly to make it easier, that was easy to remove. I removed the Grille to, along with the hood latch assembly. Re Assembly was easy, I also trimmed that rubber strip on shutter assembly that rubber was pressing so hard on the lights and wiring, I took a sharp blade carpenter knife and sliced 5/16 off it entire length, now it fits just right. And THANK YOU for a Awesome quality product. One question.. in the future if a light burns out can a single light be purchased>?
Is that a new cold air intake tube Z1 is working on? I have the cold air intake from Z1 but it's a matte black tube, not that carbon fiber looking tube in that's truck.
"Deez Nuts" (add smirk here) Lights are looking good. Just bought a set. I think they'll look as good on my white "Midnight Edition" SV. I hope everything goes as smoothly as in the vid. Fingers crossed.
@@z1off-roadInstalled them today. Good quality product. Simple job.The hardest part was figuring out which fuse to pull. Nissan didn't mark them very well.But the lights look really good! BTW, there's a cover on the far right front of the fusebox that slides up & you can fish your wire through there instead of cutting the box.
I would guess he means "orange Permatex," since Loctite is a brand name and don't believe they make an "orange" threadlocker. However, I would most likely use 'blue."
I installed as shown in the video to the ABS module 10A fuse. Might be moving. UPDATE: Changed location to the backup light circuit, hot with ignition Start and On. 10A fuse 45. It is located in the same row as the one shown in the video but other end of that row, immediately following the 15A fuse.
@z1off-road I did! How tight of a fit is putting the lights fuse in? It seems like a hard push and barely wants to sit in there as the other cables are in the way. Any advice?
@MusicManiac931 That's purely your opinion bud. Mine looks amazing, and I paid 40$ for it on amazon. I've gotten countless compliments on it. It's about the installer and doing it right.
We have an authorized installer network listed at the bottom of the home page, but this install is very simple so almost anyone should be able to do it for you.
Grill Lights for 2022 2023 2024 Nissan Frontier Raptor Lights LED Grill Lights Front Grille Light for Frontier 3rd Gen Accessories PRO 4X S SV PRO X, Amber Lights B0CSFZNDR8 i got these of amazon they were allot easier and fit great you pushed them in from outside the grill and they snaped in
That smirk when he said "these nuts"... 0:33
“Deez Nutz” 😂
detailed and helpful! camera man killing it too
I purchased these a few days ago after watching this video. I just got done installing them, and this video made it super easy. They look awesome! Thanks!
Great to hear!
Am I supposed to take out a red fuse?Does that change anything with my truck?
Need to add. Comments I have received and I actually agree with.
"Those are the weakest looking amber lights of any on the road." "They look like lines and do not fill the entire glass area." Weak looking; dude get some real lights."
Yes, they look good when installed and on. However, I would not purchase them again. Main reason was they mount from the inside out vs. others mouth from the outside in and rely on a friction fit to remain. And that does not work in all car washes. These are more secure; just too bad they did not invest in a more "fulfilling light."
Some install notations....
Ended up installing the fuse to fuse 45, 10A located on the other end of that short row of fuses from the ABS module used in this video. It is immediately under the 15A (blue) fuse at the other end of the row. (You can see the blue 15A when he is plugging in the fuse at 15:21. This fuse is hot when the ignition is ON or START. And the fuse holder fits better.
(I would add a photo but not sure how to post to this comment!)
On my '23 there are a total of five T15 torx screws that need to be removed. Two torx screws on each side. Inner is for the plastic cover, outer may just be for the grill. However, I removed the two on each side just in case; not that hard. Also there is another torx screw in the middle just to the right of the hood latch; looking at it from the front of the vehicle.
Forget those tiny tie straps. I used 3.5" black straps and they were hard enough to get locked; cannot imagine trying to use the small ones that came with the kit; at least after the lights were installed.
Even though I did NOT remove the grill, it was a pain to align back up with all the locator locking pins and it appears both sides need to be pushed in at the same time. Or at least that is what I found on my vehicle. Also those six push pins, along with where that plastic cover attaches to the grill really hold that grill in place more than the side pins.
Overall, not a hard install if you have all the right tools. At least you can do it all standing up.
Just ordered these, cant wait to get em...just bought the 24 Pro 4X early August in the Super Black color and these lights are gonna look sweet.
You should always test before fastening everything back
I installed this today on my 2023 P4X. It was easy, however I did one thing different, I removed the shutter assembly to make it easier, that was easy to remove. I removed the Grille to, along with the hood latch assembly. Re Assembly was easy, I also trimmed that rubber strip on shutter assembly that rubber was pressing so hard on the lights and wiring, I took a sharp blade carpenter knife and sliced 5/16 off it entire length, now it fits just right. And THANK YOU for a Awesome quality product. One question.. in the future if a light burns out can a single light be purchased>?
We are always here to support in anyway we can. Just reach out to the team.
I need a good hood decal installed video?
Is that the fuse you are using, the ABS ECU 10A fuse?
0:32 I see that smile after saying Deez Nuts 😂
Those lights look great. I know you guys want to get the super charger right but dude, when are we going to get some more info on it? Me wants!
I wonder what that super charger does for the warranty?
@@Sand15676voids it 😂
when is the supercharger coming and whats stopping you as of now?
We are currently searching for beta testers as we speak.
what about the Titan? Such a huge market!!! You guys could capitalize on the titan market!!!!
White LED option coming soon?
What is the tire /wheel setup ?
35x12.5R17 Toyo Open County MT on our ATK-06s
please find a new video editor
Do you guys plan on making these for the 2025 model in the future?
These will still work for the new grill as well.
@@z1off-road Just tried to put them onto the grill and definitely don't fit the new grill.
@@805native1 These are currently in the grill of our 2025. They just don't fit in the openings right next to the emblem.
@@z1off-road Guess I would need to see on how you guy's installed them.
Is that a new cold air intake tube Z1 is working on? I have the cold air intake from Z1 but it's a matte black tube, not that carbon fiber looking tube in that's truck.
The carbon is for the supercharger kit, but if enough people start asking for it... maybe.
"Deez Nuts" (add smirk here) Lights are looking good. Just bought a set. I think they'll look as good on my white "Midnight Edition" SV. I hope everything goes as smoothly as in the vid. Fingers crossed.
The install is super simple, reach out if you have any questions.
These will look great with that Midnight Edition Grille
@@z1off-roadInstalled them today. Good quality product. Simple job.The hardest part was figuring out which fuse to pull. Nissan didn't mark them very well.But the lights look really good! BTW, there's a cover on the far right front of the fusebox that slides up & you can fish your wire through there instead of cutting the box.
Did you already post a video on the supercharger install?
No we have not, this one is still the prototype. Once we have the full kit ready for sale we will post one.
I would guess he means "orange Permatex," since Loctite is a brand name and don't believe they make an "orange" threadlocker. However, I would most likely use 'blue."
Don’t like the color of these lights. Look bad at night. Do they come in other colors?
What lift is that? Stance is tough
It is our titan swap kit with Radflo 2.0s and a 2" body lift.
Those are markers lights and you should tap on the markers fuse. Not ABS
I installed as shown in the video to the ABS module 10A fuse. Might be moving. UPDATE: Changed location to the backup light circuit, hot with ignition Start and On. 10A fuse 45. It is located in the same row as the one shown in the video but other end of that row, immediately following the 15A fuse.
Huh!? W one!?
@@omarroyval9737 the fuse marked “markers” under the hood
@@f5fstopWhy did you move?And should I use the fuse you suggest?
Dee’s nuts😂
Do you not have any rubber mat so you can put on top of the table to protect your body part on?
Please make em in yellow
Why does this video not properly show which fuse to tap into?
You can always refer to the install guided for any additional detail.
@z1off-road I did! How tight of a fit is putting the lights fuse in? It seems like a hard push and barely wants to sit in there as the other cables are in the way. Any advice?
2025 Ranger Raptor Doesn't even have these Cosplay Lights.
If your not driving a full sized Raptor its all Cosplay and we Know it!
The other kit the lights just snap in...much easier to do
And cheaper!
Those other kits look like shit though. You get what you pay for.
@MusicManiac931 That's purely your opinion bud. Mine looks amazing, and I paid 40$ for it on amazon. I've gotten countless compliments on it. It's about the installer and doing it right.
@MusicManiac931 lol follow the angle of the grill...keep the lights looking uniform. No one is judging you for spending more do ya thing
@@garym51124 Exactly! 💯
Who can I have install these on mine?
We have an authorized installer network listed at the bottom of the home page, but this install is very simple so almost anyone should be able to do it for you.
You need a new camera guy, he wont give us close ups of what your doing behind your hand where we cant see.
We are currently looking for one if you know someone.
Man this is doing too much
Grill Lights for 2022 2023 2024 Nissan Frontier Raptor Lights LED Grill Lights Front Grille Light for Frontier 3rd Gen Accessories PRO 4X S SV PRO X, Amber Lights B0CSFZNDR8 i got these of amazon they were allot easier and fit great you pushed them in from outside the grill and they snaped in
Nope
Will those lights fit the Nissan Titan? The grille looks the same size slots.