I would like to add a tip for anyone doing this, compress the bag to the height you want and wrap the fitting with electrical tape, it will slowly reinflate then and can really help you get the assembly into position on tight installations.
wow. This is maybe the BEST youtube video I've seen. Not one of those guys that posts stuff and likes listening to themself ramble. All business and very information. Thank You!
You are the man! I’m putting air springs on my f-150 , only because they were free, lol, and I removed the factory bed and replaced it with one I built, I made the top as low as possible for easy loading and unloading when I use the truck later, this resulted in very tight clearance over the back tires, it’s just barely enough, i had intended to add a leaf, then someone gave me two air springs that are for a dump truck, specifically they are the bags that put weight on the drop axle once it’s down. I’ve discovered they are nearly identical to those LoadLifter 5000 bags, I suspect the loadlifter bags can handle more than 5000 pounds, I think these I was given are 5000 each, but they are dimensionally identical, and the same ply. Not that I would ever even consider putting that much on a pickup, lol. I just found it interesting those loadlifters are the same bags. If you see this(video is an older one) I would be interested to know how you like the air springs after you have ran them for a while? THIS IS AN AWESOME VIDEO!!! Short and to the point. All the info I needed as well, I was only given the bags, I have to fabricate the hardware, I can see that in your vid well enough and you supplied enough on torque specs and location that I’m confident I can install them safely. Thank you! Was that hardware stainless steel? It looked like shiny stainless in the video. Also, I would like to mention, I have researched all this a lot last couple of days, there are some control systems out there that are pretty reasonable for controlling pressure in your bags from the cab. Looked pretty easy to install, especially the wireless version, of course is more expensive , I’m going with what they call the analog version, it comes with a small panel you mount on the bottom of your dash and gives you a gauge for each bag so you can check pressure at a glance from the drivers seat and adjust if needed by turning the control knob on the panel. You could even just look the set up over and get the parts to make it yourself most likely.
After running the load lifter 5000 for sometime now I really would recommend them they have been very good for me. I’m not sure if the parts were stainless steel, can’t remember but I’m sure that something that can be looked up. Thanks for watching.
I’m glad I actually bought the Firestone brand, and not this nightmare of a copy. Number one, the trust is absolutely bad. And two, great video, great help for whoever buys the kit you did.
I bought this setup for my 2002 F350 DRW late in 2018. Watched the videos and installed it. Turns out it probably overloads the bumper stops as he calls them. my 17 year old truck broke one of them. I then figured it was a fluke and bought a replacement at a local wrecking yard. A tough deal as my truck had angled ones. I had to replaced my u-bolts to install them and then went on a 400 mile round trip. Guess what? broke again. I have now purchased after market mounts from an ebay seller that will eliminate the bump stops and let the air bag ride directly on my dana 80 rear axle. The first repair cost me over $80 plus time and the second will be about $40 plus time. Wish I knew how fragile these were to start with. I also don't like the clamping method to hold it in place on the bottom. Real bush league. My new system will look like a real strong installation.
A while back I had the opportunity to change the shocks while I had the bed off but ran out of time. I may have to change them out in the future so stay tuned. Thanks for the comment
Are you not concerned that under a load body roll will increase because the T-Fitting will allow air to move freely between the bags? It seems like in a left turn the right side will have more pressure and force air into the other side causing more roll.
It seems to work quite well so far...I have had 2,300 lbs in the truck and towed a 35 ft. trailer with no problem. It definitely helps the handling under load because it keeps the truck level. Thanks for the question, hope this helps.
Curious, 1st Ive' read where someone intentionally tied the bags together. Then again my weight is in bed (3500+# slide in camper) so other than added weight handling is resisting lean/side to side roll. Tied together if truck leans to one side, instead of bag resisting, load would push the air into opposite bag, leading to increasing lean. Just an observation- if its working for you great-
Its not water that flows side to side. Seriously. I have a Kenworth that has 8 bag air ride and haul over 80,000 gross all the time and it makes no difference when cornering.
In your install, you used a "T" fitting so that both sides have same pressure. I'm wondering if now that you've had it this way for awhile if you would to that again or would rather have them separate? Reason I ask is, if one of them were to start leaking, how would you know wish one? I'm installing my Load Lifter tomorrow and was thinking of doing the "T" fitting but wanted to hear your feedback.
I would probably still do the T fitting. As of now I do not have a leak so all is well. The other advantage to doing them separate is that you can adjust the level by putting more pressure in one side, but for me this works well. Thanks for watching.
Getting ready to install these on my 250 super duty. We have a 33 foot camper that likes to sway. I am hoping this and a new anti-sway hitch will help.
Are you worried at all about the exhaust by the air bags? also any idea what size spacers are under the old bump spot, i bought some bags used and they never came with the spacer
Hi I have the same truck and the same kit. Did you have any trouble with the shock bracket in the way so you couldn't move the lower bracket over far enough to get the bag straight.
Could you offer a link to product please? I've got an f250 2007 and Amazon says it won't fit my truck (not that that's always the truth). Or maybe the product model number. Thanks!
The firestone ride-rites come with a heat shield/deflector for the right side to shield the tail pipe. The load lifter options don't seem to have that. Any knowledge of why or why not? It seems the spacing from the bag to the tail pipe would be about the same on either product.
I believe the tubes and fittings are 1/4" and I cut the tubes after I ran them to their correct location so that they would be the exact size needed. Hope this answers your questions, Thanks for watching.
Great video! I am looking at doing this with my truck. This has been really helpful. Did the T fitting for the air lines come with the kit? If not where did you get it?
That is something that you will have to investigate. Many people like different things and have different applications. Check out some forums on the topic and see what most people are saying is the ups and downs of your set up, Hope this helps, Thanks for watching.
Do you happen to have a hardware(nuts and bolts lengths and size) list for this exact install? I just bought a kit off a used truck and I have only half or less of the nuts and bolts that I need to install them. I believe I have all the brackets but I will need to purchase the hardware.
Where you routed the air lines through the frame, grommets would have helped to prevent chafing. Also, wonder why people always place the air fill in the worst place for dirt and grime, not to mention, under the truck where access is poor. Would be better up higher with a gauge to have preset load numbers.
It would be nice to have a pressure regulator, and air dryer, and air oiler in order to keep the tools well lubricated, a more convenient location for the air outlet, a larger air tank, and a larger compressor. But as it stands this set up works very well for what I use it for and is has for some time now. Thanks for watching.
It can be a harsh ride if the bags have too much pressure. I usually run a very little bit of pressure unless I am towing or hauling then I pump them up till the truck is level. Thanks for watching
Funbro 1 thanks for the Video! Anyone ... Ive got a couple questions had an issue with the B&W tractable Gooseneck frame plate being in the way of step 1?I also must have a newer version of the Airlift 5000 a few items were not assembled but I figured it out
Please test the air connections before you try to install. Mine leaked at the brass fitting insert that goes into the plastic end cap (yup they are plastic if you order them thru any online retailer). That cannot be repaired and I doubt you’d see any bubbles if you sprayed a soapy solution when installed. Called the company and they want you to submit an online request. They are not willing to overnight a replacement to a brand new defective part. Their warranty on a brand new product is too slow if you are planing a time to do the install. Makes me wonder what would happen if you’re on the road and there is a warranty issue. Ah sir, go on line and submit a request, while your truck suspension is out of service? Be aware.
Hola un saludo desde tomatlan Jalisco México en la costa norte de Jalisco mi pregunta es enque lugar compro e instalan estos equipos de suspencion grccs
You shouldn't t your intakes lines. In a turn you can push air from one bag to the other making for a harsher ride. Separate them and you'll be better off
Manufacturer sells and recommends using a T in some instances. The only way I would do them separate is if I wanted to park on a slight hill and "try" to level the load by using more air in one side. Other than that I would not want to have to fill up two separate bags all the time, instead I'll just slow down in a turn. Really I've never had an issue. Thanks for watching.
Listen up it seems nobody is talking about trucks with lift kit I have 4" lift and purchased this the solution is to flip the top brackets literally upside down and drill holes and mount
Listen up, This is a good fix for a 4" lifted truck but the video is not for that. It is for a stock truck looking to add airbags. Thanks for watching.
No need to be fearful, a little surface rust on a vehicle of this age is to be expected. Also no need for an inspection. Try not to be so timid, and thanks for watching.
???Inspection for what? a 10-15 year old truck? whos supposed to inspect it? Its not a DOT commercial vehicle. You must live in one of those restrictive communist states. I have a 2006 F250, and its never been "inspected" by anyone but me.
I always back up my jack with proper NON-Jack support when/if I get under the vehicle. How do you know there is not a NON-jack support. OOOOOOOOOO. Thanks for watching.
Do you live way up north? I remember back in 2010, Stuttgart Germany had a scandal where the automotive manufacturers bought all the salt for the roads in the city with the instructions to salt the hell out of the roads in order to corrode the vehicles as soon as they could so the could sell more cars. I took a brand new Tacoma over there and after just tow winters, the salt had corroded the brakes so badly it failed Germany's vehicle inspection. After Germany, I don't think I would ever have a newer vehicle where they treat the roads and corrode the vehicles. A vehicle is literally ruined by salt. Also @ 3:53 I've watched a few of these videos and read the instructions for my air bags. The instructions say "no more than 20 lb/ft torque" but all the videos say "tighten to 20 lb/ft"
I went with Air Lift brand, but there are other brands that will work for your truck. You will need to contact the manufacturer to find the correct one for your truck.
go to air lifts site, you can enter your truck then it shows you all the kits that fit it, and tells you if it fits fifth wheel hitches! I chose the air lift brand because it has lifetime warranty
I would like to add a tip for anyone doing this, compress the bag to the height you want and wrap the fitting with electrical tape, it will slowly reinflate then and can really help you get the assembly into position on tight installations.
Sounds like a good tip, thanks for sharing and thanks for watching.
wow. This is maybe the BEST youtube video I've seen. Not one of those guys that posts stuff and likes listening to themself ramble. All business and very information. Thank You!
Thanks for watching.
Do what if you have a gooseneck plate in the way?
Great video and step by step instructions. Probably the best one I’ve seen
You are the man! I’m putting air springs on my f-150 , only because they were free, lol, and I removed the factory bed and replaced it with one I built, I made the top as low as possible for easy loading and unloading when I use the truck later, this resulted in very tight clearance over the back tires, it’s just barely enough, i had intended to add a leaf, then someone gave me two air springs that are for a dump truck, specifically they are the bags that put weight on the drop axle once it’s down. I’ve discovered they are nearly identical to those LoadLifter 5000 bags, I suspect the loadlifter bags can handle more than 5000 pounds, I think these I was given are 5000 each, but they are dimensionally identical, and the same ply. Not that I would ever even consider putting that much on a pickup, lol. I just found it interesting those loadlifters are the same bags. If you see this(video is an older one) I would be interested to know how you like the air springs after you have ran them for a while? THIS IS AN AWESOME VIDEO!!! Short and to the point. All the info I needed as well, I was only given the bags, I have to fabricate the hardware, I can see that in your vid well enough and you supplied enough on torque specs and location that I’m confident I can install them safely. Thank you!
Was that hardware stainless steel? It looked like shiny stainless in the video.
Also, I would like to mention, I have researched all this a lot last couple of days, there are some control systems out there that are pretty reasonable for controlling pressure in your bags from the cab. Looked pretty easy to install, especially the wireless version, of course is more expensive , I’m going with what they call the analog version, it comes with a small panel you mount on the bottom of your dash and gives you a gauge for each bag so you can check pressure at a glance from the drivers seat and adjust if needed by turning the control knob on the panel. You could even just look the set up over and get the parts to make it yourself most likely.
After running the load lifter 5000 for sometime now I really would recommend them they have been very good for me. I’m not sure if the parts were stainless steel, can’t remember but I’m sure that something that can be looked up.
Thanks for watching.
Awesome how to video. Today's kit is bacically the same. It is even simpler with a lot of 1 piece brackets and less bolts and hardware. Well done.
Glad it helped. Thanks for watching.
That was as good a tutorial as I have seen on YOU TUBE. Quick and concise.
Awesome! Thanks for watching.
Great video - getting ready to do my 2008 F250 this weekend and this will be tremendously helpful.
You will love them. Thanks for watching.
I’m glad I actually bought the Firestone brand, and not this nightmare of a copy.
Number one, the trust is absolutely bad.
And two, great video, great help for whoever buys the kit you did.
This set up has served me well for years now glad you watched the video. Thanks for checking in.
I bought this setup for my 2002 F350 DRW late in 2018. Watched the videos and installed it. Turns out it probably overloads the bumper stops as he calls them. my 17 year old truck broke one of them. I then figured it was a fluke and bought a replacement at a local wrecking yard. A tough deal as my truck had angled ones. I had to replaced my u-bolts to install them and then went on a 400 mile round trip. Guess what? broke again. I have now purchased after market mounts from an ebay seller that will eliminate the bump stops and let the air bag ride directly on my dana 80 rear axle. The first repair cost me over $80 plus time and the second will be about $40 plus time. Wish I knew how fragile these were to start with. I also don't like the clamping method to hold it in place on the bottom. Real bush league. My new system will look like a real strong installation.
Wow, what a story, thanks for sharing.
Nigga do the vid stop running your mouth
Do you happen to have the EBay sellers info or part number for the aftermarket mounting kit ?
Excellent video thank you, God bless you and your family
Thank you! You too!
Excellent video thanks so much for the help.
Glad it helped, Thanks for watching.
Down the road you should make a video on replacing the shocks on an f250! , great video
A while back I had the opportunity to change the shocks while I had the bed off but ran out of time. I may have to change them out in the future so stay tuned. Thanks for the comment
Really?? How about how to put fuel in a truck
Good job my friend I just done
A airlift XL7500 on dodge super duty today and almost the same procedure..just the brackets different..👍👍👍
I love mine, Thanks for watching.
Are you not concerned that under a load body roll will increase because the T-Fitting will allow air to move freely between the bags? It seems like in a left turn the right side will have more pressure and force air into the other side causing more roll.
Sorry switch that about the body roll. Increase on the left side and force air into the right side bag.
It seems to work quite well so far...I have had 2,300 lbs in the truck and towed a 35 ft. trailer with no problem. It definitely helps the handling under load because it keeps the truck level. Thanks for the question, hope this helps.
Curious, 1st Ive' read where someone intentionally tied the bags together. Then again my weight is in bed (3500+# slide in camper) so other than added weight handling is resisting lean/side to side roll.
Tied together if truck leans to one side, instead of bag resisting, load would push the air into opposite bag, leading to increasing lean.
Just an observation- if its working for you great-
Its not water that flows side to side. Seriously. I have a Kenworth that has 8 bag air ride and haul over 80,000 gross all the time and it makes no difference when cornering.
@@oby-1607 are all 8 tied together into one line/fill?
Excellent video, thank you
Thanks for watching.
In your install, you used a "T" fitting so that both sides have same pressure. I'm wondering if now that you've had it this way for awhile if you would to that again or would rather have them separate? Reason I ask is, if one of them were to start leaking, how would you know wish one? I'm installing my Load Lifter tomorrow and was thinking of doing the "T" fitting but wanted to hear your feedback.
I would probably still do the T fitting. As of now I do not have a leak so all is well. The other advantage to doing them separate is that you can adjust the level by putting more pressure in one side, but for me this works well. Thanks for watching.
Good job, Bob, thanks
Thanks for watching.
Getting ready to install these on my 250 super duty. We have a 33 foot camper that likes to sway. I am hoping this and a new anti-sway hitch will help.
I’m sure it will help but correct loading of the camper will go a long way as well.
Thanks for watching.
Are you worried at all about the exhaust by the air bags? also any idea what size spacers are under the old bump spot, i bought some bags used and they never came with the spacer
I'm not too worried about the exhaust it is far enough away, As for the old bump spot, I'm not sure what size they are. Thanks for watching.
Do you know if these will fit in with a B&W turnover gooseneck hitch mounted?
Not sure about that, you would need to check with Air Lift to make sure.
Thanks for watching.
Hi I have the same truck and the same kit. Did you have any trouble with the shock bracket in the way so you couldn't move the lower bracket over far enough to get the bag straight.
On mine the bags are now “exactly straight but they seem to work very well. Thanks for watching.
Could you offer a link to product please? I've got an f250 2007 and Amazon says it won't fit my truck (not that that's always the truth). Or maybe the product model number. Thanks!
I bought mine from the company. Start there, if you have any questions you can call them.
The firestone ride-rites come with a heat shield/deflector for the right side to shield the tail pipe. The load lifter options don't seem to have that. Any knowledge of why or why not? It seems the spacing from the bag to the tail pipe would be about the same on either product.
Interesting, but I have no idea. Thanks for watching.
Hi. What size are the hoses and what size was the T fitting? Did you cut both hoses equal length before connecting to the fitting? Thanks
I believe the tubes and fittings are 1/4" and I cut the tubes after I ran them to their correct location so that they would be the exact size needed. Hope this answers your questions, Thanks for watching.
Great video! I am looking at doing this with my truck. This has been really helpful. Did the T fitting for the air lines come with the kit? If not where did you get it?
The T fitting did not come with the kit it was an ad on and I got it from the manufacturer. Hope this helps, thanks for watching.
@@funbro1 that does help. Thank you!
I have a 10 inch fabtech dirt logic suspension lift kit, will this work on my truck or what would you recommend? Thanks.
That is something that you will have to investigate. Many people like different things and have different applications. Check out some forums on the topic and see what most people are saying is the ups and downs of your set up, Hope this helps, Thanks for watching.
Thanks for the help
Thanks for watching.
If I have a 6" lift on my F350 do I have to order something special?
Yes, check with the manufacturer for options.
Thanks for watching.
Do you happen to have a hardware(nuts and bolts lengths and size) list for this exact install? I just bought a kit off a used truck and I have only half or less of the nuts and bolts that I need to install them. I believe I have all the brackets but I will need to purchase the hardware.
Sorry I do not.
Thanks for watching.
Did you have to drill? I have a 2000 f350 and it appears to have the same hole pattern on the frame. Thanks
No drilling. Best of luck. Thanks for watching.
I have a fifth wheel rail kit mounted onto the frame. Do you know if that will interrupt this installation?
Thanks for the step by step video.
Not sure about that one, may want to check with the manufacturer. Thanks for watching.
Where you routed the air lines through the frame, grommets would have helped to prevent chafing. Also, wonder why people always place the air fill in the worst place for dirt and grime, not to mention, under the truck where access is poor. Would be better up higher with a gauge to have preset load numbers.
It would be nice to have a pressure regulator, and air dryer, and air oiler in order to keep the tools well lubricated, a more convenient location for the air outlet, a larger air tank, and a larger compressor. But as it stands this set up works very well for what I use it for and is has for some time now. Thanks for watching.
Thank you the video👍🏻👍🏻
Thanks for watching.
Thanks for the video was it as easy as you made it look?
hmmm, It never is. lol Thanks for watching.
That upper bracket mount looks a little hokey to me, all the stress appears to be a shear load on that one bolt. Any thoughts?
I was kinda thinking the same thing but it works we’ll still after many years, miles, and loads. Thanks for watching.
For me too
cuanto cuesta para una ram 4000. y de que tamaño o capacidad debe cer agradesco mucho su información
No estoy seguro, puede comprobar el sitio web de esa información, Gracias por ver.
Very helpful
Thanks for watching.
I've thought about doing this, is it a nicer ride when your not weighted?
It can be a harsh ride if the bags have too much pressure. I usually run a very little bit of pressure unless I am towing or hauling then I pump them up till the truck is level. Thanks for watching
Great video Have you ever run into a 5fh wheel plate that is right in the way of the mount? If so anyway around that?
No. I have never run a fifth wheel on this set up so I can't speak to this problem. Sorry. Thanks for watching.
Awesome
Thanks for watching.
Looking good!!!
Thank you! Cheers!
Is there any holes that need to be drilled in frame
Not with this kit.
Thanks for watching.
Funbro 1 thanks for the Video! Anyone ... Ive got a couple questions had an issue with the B&W tractable Gooseneck frame plate being in the way of step 1?I also must have a newer version of the Airlift 5000 a few items were not assembled but I figured it out
Thanks for watching, Let us know if you find anything out.
Please let us know. I have the same B and W hitch. Wondering how its going to work. Or if it will.
Please test the air connections before you try to install. Mine leaked at the brass fitting insert that goes into the plastic end cap (yup they are plastic if you order them thru any online retailer). That cannot be repaired and I doubt you’d see any bubbles if you sprayed a soapy solution when installed. Called the company and they want you to submit an online request. They are not willing to overnight a replacement to a brand new defective part. Their warranty on a brand new product is too slow if you are planing a time to do the install. Makes me wonder what would happen if you’re on the road and there is a warranty issue. Ah sir, go on line and submit a request, while your truck suspension is out of service? Be aware.
BRAVO !!!!!!!!!!!!!!!!!!!!!
Thanks for watching.
I just ordered this kit for my 06 f350. Did yours come with the air line tee fitting?
I had to order that separate. Thanks for watching.
What size T Fitting?
Hola un saludo desde tomatlan Jalisco México en la costa norte de Jalisco mi pregunta es enque lugar compro e instalan estos equipos de suspencion grccs
www.airliftcompany.com/
Good clip man
Thanks for watching.
I would use Teflon tape for that air connection
I thought the same thing but after reading the instructions it did not recommend Teflon tape. Not sure why. Thanks for checking in.
You shouldn't t your intakes lines. In a turn you can push air from one bag to the other making for a harsher ride. Separate them and you'll be better off
Manufacturer sells and recommends using a T in some instances. The only way I would do them separate is if I wanted to park on a slight hill and "try" to level the load by using more air in one side. Other than that I would not want to have to fill up two separate bags all the time, instead I'll just slow down in a turn. Really I've never had an issue. Thanks for watching.
Do they make these for a 1997 f250? 7.3 2wd obs
You would have to consult their website to find your answer. They do make kits for many trucks. Thanks for watching.
Great video man. Very explanatory unlike some other clowns on UA-cam. One question, is yours a 4wd??
Yes this is on a 4WD. Thanks for watching.
funbro1 where did you get the t air hose fitting
Regarding the jounce bumper: "you may need to grind the nut off". Does that mean you had to? I just spent over an hour getting that damn thing off!!
I might have on one of them. Thanks for watching.
How ling did it take start to finish?
It took a little longer with making the video and all but start to finish it can probably be done in a few hours. Thanks for watching.
Great Video! No Table to lay out materials & tools? Knees on concrete not for me.
It's not easy and definitely not for everyone. Thanks for watching.
Good video
Thanks for watching.
the shop down the street wants $200 for the install, worth it? Or should I do it myself... here's some background: I'm lazy and accident prone :)
Worth it...to me.
My mechanic quoted me $300 with the wireless compressor. I couldn't write that check fast enough.
Are they doing a custom job installing the compressor with a SS skid plate? Part of the reason I had to do my own. Thanks for watching.
The shocker's was removed?
No, they stay in place. Thanks for watching.
What year is your truck brother?
This project was done on a 2007. Thanks for the comment.
Will this fit my 02 super duty
I think the 02 is a different set up but there is a system out there for it. Thanks for watching.
You ever replace the shocks? Jeez I bet they have over 80k on them
Jeez they may? Not really thought about how many miles the shocks have on them. Thanks for watching.
@@funbro1 it was a great video btw, thanks for sharing.
Listen up it seems nobody is talking about trucks with lift kit I have 4" lift and purchased this the solution is to flip the top brackets literally upside down and drill holes and mount
Listen up, This is a good fix for a 4" lifted truck but the video is not for that. It is for a stock truck looking to add airbags. Thanks for watching.
How'd You feel towing with these afterwards?
Very much improved, better handling, and control of the load. Thanks for the question.
funbro1 What was the year make and model of your f250 if you don't mind me asking?
It is a 2007 F250 FX4 crew cab with a 6’ bed.
by the looks of that frame I don't even think that thing would pass inspection I'd be afraid to pull anything with that truck
No need to be fearful, a little surface rust on a vehicle of this age is to be expected. Also no need for an inspection. Try not to be so timid, and thanks for watching.
???Inspection for what? a 10-15 year old truck? whos supposed to inspect it? Its not a DOT commercial vehicle. You must live in one of those restrictive communist states. I have a 2006 F250, and its never been "inspected" by anyone but me.
Is this truck 4x4?
Yes it is a 4x4. Thanks for watching .
id be replacing those crusty shocks before worrying about putting air bags on that truck
No need to replace working shocks that work perfectly fine just to have "pretty" shocks. It is a work truck. Thanks for watching.
Maybe he can get some pretty pink shocks just to be a cutie pie
you would be surprised how much better a set of bilstein's are than the factory fake ranchos
I may have to try a set
Probably with those bags don't even need shocks
relying on a jack only is not wise... always backup your jack with proper NON-jack support!!!
I always back up my jack with proper NON-Jack support when/if I get under the vehicle. How do you know there is not a NON-jack support. OOOOOOOOOO.
Thanks for watching.
Please do me a favor next time use a jack stand.
No favors are needed. Everything was done in a safe manner. Thanks for checking in.
@@funbro1 great job on the installation I appreciate it.
I would have liked this video but you didn’t mention wrench sizes… waist of time!
That’s OK, I would have liked your comment, but it was useless… waste of time.
Should have spent some money in new rear shocks! Yikes!
And the list goes on and on as far as the things that should have spent money on. ONE thing at a time. Thanks for watching.
Wow, the corrosion.
The bags are brand new, no corrosion on them? Thanks for watching.
Do you live way up north? I remember back in 2010, Stuttgart Germany had a scandal where the automotive manufacturers bought all the salt for the roads in the city with the instructions to salt the hell out of the roads in order to corrode the vehicles as soon as they could so the could sell more cars. I took a brand new Tacoma over there and after just tow winters, the salt had corroded the brakes so badly it failed Germany's vehicle inspection. After Germany, I don't think I would ever have a newer vehicle where they treat the roads and corrode the vehicles. A vehicle is literally ruined by salt.
Also @ 3:53 I've watched a few of these videos and read the instructions for my air bags. The instructions say "no more than 20 lb/ft torque" but all the videos say "tighten to 20 lb/ft"
I live in the Mid-west. They do use salt here :-(
Need more light!!
I will make a video on replacing the headlights, stay tuned.
Bump Stop
Air bag with bump stop
👍👍👍👍👍🍺😎
Thanks for watching.
Can this kit be used with a fifth wheel application? I have a 1996 F250 P/U 4x4 8" bed
If not this kit they do make a similar one that would greatly improve the handling while towing. Thanks for the question.
Do you know what type of kit you recommend?
I went with Air Lift brand, but there are other brands that will work for your truck. You will need to contact the manufacturer to find the correct one for your truck.
go to air lifts site, you can enter your truck then it shows you all the kits that fit it, and tells you if it fits fifth wheel hitches! I chose the air lift brand because it has lifetime warranty