Michael Rhoades, Yeah I expected there to be some issues. Nothing to major. Collect what you can so when you start the swap you can rock and roll on it. Thanks for the comment.
Not sure if the plug end is the same , or if it will even fit, but both the cam position sensors on a 2011 chevy Cruze come out of the sensor straight, yours turns 90 degrees. And they are 3 wire. Might be worth looking into prior to moving the fuel cell. Part # SU13343 from autozone is the intake side.
Holy cow! Good tips with part numbers, nice. I'll look into it. I might need to mess with the fuel cell either way for access to the rear of the block but this might give me some options. Thanks!
sweet ....my buddy is a fabricator and mounted one of these eco tecs in a 1988 bmw e30..he also mounted it inline using a toyota 5 speed trans... turbocharger..custom intake and intercooler with header...thing was a rocket til he rolled it..whoo hoo
@@DougBugBuilder "was pretty quick" he rolled it...a car he built before this bmw.. i mentioned was a 63 bug, he put a street ported 13b rotary in it..which as you know must be water cooled..he seen the idea out of a 70s custom bug mag and figured it would be cool..the thing was a rocket! scarey fast off the line! he rapped that one around a light standard as well!
Being watching your vids and your doing a lovely job on the baja. I personally would have stuck with the original vw engine, i noticed CB performance do big stroker dub motors which would have delivered great torque and power plus kept it very light.. But its your baja and i respect your decision.. still very keen to see how it all works for you.. just subbed... keep em coming cheers from Tasmania....
Hey Buddy, Welcome to the channel, good to have you on the team. lol It has been interesting seing the differences between the air cooled and Ecotec so far. My Bug was really light and simple with the air cooled motor. It was a little heartbreaking taking that out and adding all the components to operate the Ecotec. I hope it's worth it. The air cooled is safely in the basement, so we might see it again. ;-)
The engines from CB performance are really high dollar, you can get a ectec for what 250 dollars and have 160+ HP takes more money to get 160 HP from a VW engines, I know all about it I've played with VWS for a long time, still do some
Pretty similar to the VW, but there are no dowel pins. Just six bolts hold it to the end of the crankshaft.
6 років тому
Just looked into this engine as been trying to decide what engine to go with, but this has a compression of 12:1...can't drive onto the airport tarmac anymore for avgas like we used to. R u going to have to run premium and octane boost, or just premium?
Adapter kit is awsum I wounded if I could put a fwd motor and trans from Camry 2.2 or 2.4 and use axles and struts just put it from for front to rear amazing work your doing what do you do for living
Doug. Ls motor L's 3 heads L's x or L's 1. Use crank use càm head work to L's 3 heads. They prove time and time HP come from L's 3 heàds. Stock short block head work ànd ls3 and high lift. Can. Ànd in return over 1000 horse power the best design in ten years racing guys are going nuts L's motors I've not done one but I'm sure I can I e built hundreds of engines I'm a problem fixer alluminum engine blowi hg head vskt because studs were pulling from block we fixed made inserts for blocks new studs ne2 nuts lß motors next on my list after I fix my roof hericanetook a little roof out I'm in north Carolina. Burgas nc
Filling these with oil/doing filter changes in a beetle kinda suck, but the ecotec is a great swap. Wiring is super easy too! Just make sure to get your oe pcm security hacked (if you're running that) or it won't start.
I'm learning a lot. How do you sleep I don't sleep I think to much best time for me is when I sleep ive. Fixéd a lot of stuff in my sleep and repair next day I think I'm nuts sometimes
I worked with 54 techs at one time a big Toyota dealérship we sometime fixed problems with new cars write reports for Toyota for warrentee suggest ways to fix problems Toyota ahead of the rest great car .I spent 23 years there and my dad owned the oldest Volvo dealership in america first ducatti and subura also I don't no anything else no I'm disabled at least they tell me I am got hit head on.sucks but I can sleep in
"Accessing this bolt for me is almost impossible" Seems like that's pretty common on completely stock vehicles both classic and new, European and American. Looks fun.
For once, someone takes the time to show folks how they do some of the wild builds they do. My 8 yr. old has really shown some interest in our bug build...
Hi Doug. I have a few questions I hope you can help me with. I live in Australia and from what I can gather there are no aftermarket Baja bug suspension kits available. Do you know of any in the US that I could use/talk to. I am interested in doing something very similar regarding suspension but to get home made suspension through engineering here in Oz would be near impossible. Any help would be greatly appreciated. Great video's keep them coming and hope to hear from you soon. Have a great Christmas
rottysaurus, You can't buy an A Arm setup like mine, that's a one off that I made myself. However there are some companies that make good trailing arms for the front or rear suspension. Try Kar-tek Offroad, Appletree Automotive, Chirco, and Air Cooled.net. These are all companies that carry good parts. Hope that helps!
That would work.....But would really take a lot of work because of all the connection points I made on the transaxle. There would be a lot of fabrication involved. Not like that ever stopped me before though. Thanks for the idea though.
Doug Bug you're welcome and I wasn't thinking about the work that's already been done.. but the the downfall to custom projects they never seem to find a true finished point. Always somthing that can be improved or changed up.
Hi! I´ve been following your build from a while, and using most of your tips (as much as I can, money here is an issue), trying to get a rear suspension like yours I found a ford T-bird rear suspension with basically the same configuration, so I adapted it to my bug. I really admire you and your craftsmanship, and I hate you ´cause I can´t follow your rythm building my bug hahahahaha. The good thing about it, is that when I start building something, you already built a better version and I can follow the new one hahaha. However, your videos are very educational and motivating. Keep up the good job!
Hello Carrillo, thanks for the comment. It was really nice and I love hearing stories like this. I'm so glad the videos are helping you some with your build. Using existing parts like you are to integrate into your design is an excellent way to save some money and time. Especially if you can get them from a doner car or junkyard. Good luck with the build, and reach out to me if you have any questions.
The bolts for the motor mounts were dictated by the threads that were already in the side of the Ecotec motor. If I remember correctly they were 12mm x 1.25mm.
Hey Mike, hope you don't mind I have recommended your channel to a couple people, it would be a shame for someone that's in to Baja's not to be able to enjoy your work!
Hey Mike, I know you stand behind Lincoln welders so I have been spending a lot of time looking at the Lincoln 210 mp, the reviews on the stick and mig are really good, the tig seems to be ok, but I guess you have to wire up the foot pedal, but i'm ok with that.i have a couple of questions I see that most of the time I am seeing gas with the mig welding is that when you don't have flux core wire or do you always need gas to weld mig, and do you recommend gas? and my other question is can you mig and tig aluminum with this machine. thanks Mike
That welders tig process is not AC, so it won't do aluminum. Don't buy it. You really have to step up in the welders to get AC tig. You will really need two welders. One for mig and one for tig. The benefit is you can get the mig now and in a couple years if your fab skills are still growing you can get an AC tig and start tigging aluminum. www.homedepot.com/p/Lincoln-Electric-180-Amp-Weld-Pak-180-HD-MIG-Wire-Feed-Welder-with-Magnum-100L-Gun-Gas-Regulator-MIG-and-Flux-Cored-Wire-230V-K2515-1/100670932 For the money I think that is the best Lincoln welder for Mig. It will do mig or flux core. If you do mig you will need gas. The gas will be a mixture of Argon and CO2. If you do flux core you wont need any gas. The Lincoln Square Wave Tig 200 is a good choice for a garage tig welder that will rock and roll aluminum. For tig you will need 100% Argon for your shielding gas. Almost any tig welder will stick weld as well. Of course there are no name brand welders for a fraction of the price. That's up to you. They are likely fairly good. All I can say is both of my welders are 20+ years old, local supply houses support them. And when I go out into the garage both of those welders look at me and say "what are we welding today"!
Mike , right now I have a brand new Chicago .stick welder and a new dual mig, I bought both from my neighbor for 150, they both came with carts, rod ,wire, helmet, and and a big fat book on everything you need to know about welding. Mike I couldn't pass this up for the price, these are only temporary, I will be getting much better quality stuff soon. would you agree this is a good way to practice on small welding to sorta get the hang of it. I have already built a little dog for my wife and I had a blast doing it. now I know why its called stick welding, but after a while I was going along pretty good, then it got fun. again these cheap welders are only temporary! Now time for another episode of Doug Bug
Mike that's perfect! A great way to dip into the waters and test some stuff out, for $150 that's a steal. Now you can fiddle around and casually look at an upgrade if you decide to go that route.
I don't run a T-stat on this engine. The temperature is controlled by the electric fans on the radiator. I got the air out using a plug as a bleeder on the leaving port for the radiator line up near the valve cover.
My favorite is the LE5 block with the VVT. The VVT really helps with low end torque. It reminds me of the old Honda XR bikes. They growl at the low end, but keep chugging along. Mine is an LE5 and it came from a 2007 Cobalt.
Great videos. I think it's crazy that the adapter costs twice as much as the engine! How hard would it be to build your own adapter, to keep it really cheap? You just tripled your budget!
Yeah I agree. We need a couple million more people to start buying these adapters to drive the costs down. I don't have machine tooling big enough to make anything like that. Otherwise I would. Thanks for the comment bud.
Awesome video, thank you for taking the time to post it. Was the flywheel modified at all to fit the VW transmission/clutch/pressure plate or does it happen to work for that particular swap?
Thorvald Moen, This flywheel comes with the kit and is machined to fit the VW transaxle with 200mm flywheel. So on one end it is machined just like a VW flywheel and on the other end it is machined to mate with an Ecotec 6 bolt crankshaft, and when it it designed/machined the proper offsets are put in it. I paid a little extra to have it lightened, but that didn't affect any of the fitment. I hope that answers your question.
Nope, the oil returns just fine, and no problem with oil pressure either. Every time I have the valve cover off the timing chain looks like it's getting plenty of oil too. I will say I do keep it up to the top on the dipstick. And leaned back that's a bit of extra oil. But I haven't had any issues.
The downfalls would be that the stock transmission isn't really meant for that kind of power. So it makes the likely hood of breaking the transmission really high.
I would stay focused on keeping whatever ground clearance you have due to future losses with some type of skid plate protection. Also center of gravity and overall balance something to keep in mind. Nothings perfect and you have the skills to change things later. I enjoy your thought process
Hey EZGZ, You are right. My first plan is to look into the oil return in the head of the motor. I don't want to change the angle. I like it and it helps with the tail draggi'n. I just need to make sure the oil can drain out of the head.
No, the brackets I used were on the engine in the chevy Cobalt when I picked it at the junkyard. I used those to set it in the chassis as well. Then once it was in there I unbolted them.
This is the stock VW starter. It bolts in the original location and everything. The Ecotec has a provision for a starter. But with the adaptor flywheel you retain the original starter in the original location in the VW transaxle.
Doug Bug. I am doing a engine swap in my Baja. My engine is a Mitsubishi Lancer 2.0 only because own the car where I don't have to buy another engine. Wondering if you can help me about the ECM. Do you know if the place how did your do other car manufacturers ECMs?
Doug Bug. Thanks!! What did you use to hold your fenders on with? You drilled a hole and insert the peace in & the tool name. I'm going to get some of them. You didn't mention what they wear in your video. Thanks for all the video's you are very good!
David, Throse are called rivit nuts. Here is an example of a kit similar to mine. amzn.to/2BmCzLF The rivit nuts I used on those fenders were 5/16-18. The tool I used is an industrial one from McMasterr Carr. It was like $180. But the link I gave you there is for a similar one just not as industrial. The choice is yours. ;-) Make some test sets first to get comfortable with it before you drill into the bug. Once you get the hang of it they are great though.
Didn't even think about that, a rotary would be a pretty cool motor to hang off the back there. I guess the answer is because I don't have any experience with the rotary motors.
Cali Coca, Thanks bud, I am still going to monitor the oil return just to be safe. If needed I can add a drain line at the rear of the head back into the oil pan. But with you saying it should be ok I'm going to just keep an eye on it. You can always email me direct at dougbugbuilder@gmail.com. Thanks.
I like how you take you time to do things, you make everything look so easy to do.
Did this 11 yrs ago on my 69 bug. Still going strong.
Nice!
i know there is fitment issues but in the long run the fuel injection i heard it will be worth it.I am still collecting parts for my swap
Michael Rhoades, Yeah I expected there to be some issues. Nothing to major. Collect what you can so when you start the swap you can rock and roll on it.
Thanks for the comment.
Not sure if the plug end is the same , or if it will even fit, but both the cam position sensors on a 2011 chevy Cruze come out of the sensor straight, yours turns 90 degrees. And they are 3 wire. Might be worth looking into prior to moving the fuel cell.
Part # SU13343 from autozone is the intake side.
Holy cow! Good tips with part numbers, nice. I'll look into it. I might need to mess with the fuel cell either way for access to the rear of the block but this might give me some options. Thanks!
And just to be clear the only thing holding the motor up is the trans, just like with the VW engine?
sweet ....my buddy is a fabricator and mounted one of these eco tecs in a 1988 bmw e30..he also mounted it inline using a toyota 5 speed trans... turbocharger..custom intake and intercooler with header...thing was a rocket til he rolled it..whoo hoo
Nice! With a turbo that thing must be pretty quick.
@@DougBugBuilder "was pretty quick" he rolled it...a car he built before this bmw.. i mentioned was a 63 bug, he put a street ported 13b rotary in it..which as you know must be water cooled..he seen the idea out of a 70s custom bug mag and figured it would be cool..the thing was a rocket! scarey fast off the line! he rapped that one around a light standard as well!
Being watching your vids and your doing a lovely job on the baja. I personally would have stuck with the original vw engine, i noticed CB performance do big stroker dub motors which would have delivered great torque and power plus kept it very light.. But its your baja and i respect your decision.. still very keen to see how it all works for you.. just subbed... keep em coming cheers from Tasmania....
Hey Buddy, Welcome to the channel, good to have you on the team. lol
It has been interesting seing the differences between the air cooled and Ecotec so far. My Bug was really light and simple with the air cooled motor. It was a little heartbreaking taking that out and adding all the components to operate the Ecotec. I hope it's worth it. The air cooled is safely in the basement, so we might see it again. ;-)
Ecotec>air-cooled but yes vw engines are more simple.
The engines from CB performance are really high dollar, you can get a ectec for what 250 dollars and have 160+ HP takes more money to get 160 HP from a VW engines, I know all about it I've played with VWS for a long time, still do some
@@steveenglund3742 I need to find a good one price at 250.
What transaxle you use? If VW will it stand the power from the engine
Hi Mike. can you explain how the flywheel bolts to the crank shaft of the Ecotec
Pretty similar to the VW, but there are no dowel pins. Just six bolts hold it to the end of the crankshaft.
Just looked into this engine as been trying to decide what engine to go with, but this has a compression of 12:1...can't drive onto the airport tarmac anymore for avgas like we used to.
R u going to have to run premium and octane boost, or just premium?
Great stuff Doug 👍 it's looking good
Thanks dude!
Adapter kit is awsum I wounded if I could put a fwd motor and trans from Camry 2.2 or 2.4 and use axles and struts just put it from for front to rear amazing work your doing what do you do for living
The oil problem what they do sometimes is put a cage around oil pump screen keeps oil there at all times
Doug. Ls motor L's 3 heads L's x or L's 1. Use crank use càm head work to L's 3 heads. They prove time and time HP come from L's 3 heàds. Stock short block head work ànd ls3 and high lift. Can. Ànd in return over 1000 horse power the best design in ten years racing guys are going nuts L's motors I've not done one but I'm sure I can I e built hundreds of engines I'm a problem fixer alluminum engine blowi hg head vskt because studs were pulling from block we fixed made inserts for blocks new studs ne2 nuts lß motors next on my list after I fix my roof hericanetook a little roof out I'm in north Carolina. Burgas nc
Filling these with oil/doing filter changes in a beetle kinda suck, but the ecotec is a great swap. Wiring is super easy too! Just make sure to get your oe pcm security hacked (if you're running that) or it won't start.
Thanks MrTurbo, I ended up getting the PCM flashed by Alpha Fab.
Doug Bug Good deal, that's where I got mine done at. People always ask me why their ecotecs won't start... Sweet build!
I'm learning a lot. How do you sleep I don't sleep I think to much best time for me is when I sleep ive. Fixéd a lot of stuff in my sleep and repair next day I think I'm nuts sometimes
I worked with 54 techs at one time a big Toyota dealérship we sometime fixed problems with new cars write reports for Toyota for warrentee suggest ways to fix problems Toyota ahead of the rest great car .I spent 23 years there and my dad owned the oldest Volvo dealership in america first ducatti and subura also I don't no anything else no I'm disabled at least they tell me I am got hit head on.sucks but I can sleep in
Hole punch what are you using for brkts looks pretty cool
What tipe of transmission are you using, I have the same motor
It's a stock Bus Type 2 with the 5.37 R&P. It's held up this far. Has about 1,000 miles.
"Accessing this bolt for me is almost impossible" Seems like that's pretty common on completely stock vehicles both classic and new, European and American. Looks fun.
Yeah there almost always seems to be one or two bolts that are a real pain. ;-)
Hi Doug what stage clutch are you running? I'm in a middle of a ecotec swap myself awesome job you did
Stage 1, good for I think 250hp. And my Ecotec should be around 175hp.
For once, someone takes the time to show folks how they do some of the wild builds they do. My 8 yr. old has really shown some interest in our bug build...
Thanks, I hope you get the chance to do some wrenching with your kid. I think those are great experiences growing up.
@@DougBugBuilder I wish sequential transmission didn't cost so much. I'd love to have one...
Hi Doug. I have a few questions I hope you can help me with. I live in Australia and from what I can gather there are no aftermarket Baja bug suspension kits available. Do you know of any in the US that I could use/talk to. I am interested in doing something very similar regarding suspension but to get home made suspension through engineering here in Oz would be near impossible. Any help would be greatly appreciated. Great video's keep them coming and hope to hear from you soon. Have a great Christmas
rottysaurus, You can't buy an A Arm setup like mine, that's a one off that I made myself. However there are some companies that make good trailing arms for the front or rear suspension. Try Kar-tek Offroad, Appletree Automotive, Chirco, and Air Cooled.net. These are all companies that carry good parts.
Hope that helps!
Hi doug do you have this gentlmens info in regards to a front a-arm kit??
Looks like a small spacer to raise the front of the transaxle would help reduce the angle and maybe even help with clearance issues too
That would work.....But would really take a lot of work because of all the connection points I made on the transaxle. There would be a lot of fabrication involved. Not like that ever stopped me before though.
Thanks for the idea though.
Doug Bug you're welcome and I wasn't thinking about the work that's already been done.. but the the downfall to custom projects they never seem to find a true finished point. Always somthing that can be improved or changed up.
That's the curse and the joy. ;-)
Hi! I´ve been following your build from a while, and using most of your tips (as much as I can, money here is an issue), trying to get a rear suspension like yours I found a ford T-bird rear suspension with basically the same configuration, so I adapted it to my bug. I really admire you and your craftsmanship, and I hate you ´cause I can´t follow your rythm building my bug hahahahaha. The good thing about it, is that when I start building something, you already built a better version and I can follow the new one hahaha. However, your videos are very educational and motivating. Keep up the good job!
Hello Carrillo, thanks for the comment. It was really nice and I love hearing stories like this. I'm so glad the videos are helping you some with your build. Using existing parts like you are to integrate into your design is an excellent way to save some money and time. Especially if you can get them from a doner car or junkyard. Good luck with the build, and reach out to me if you have any questions.
Not something the average guy could pull off. Nice work. I think a stubby Gearwrench might work on the starter?
Thanks buddy, you might be right on the wrench! That thing was a bugger to get!
Can you tell me what size bots you use for the ecotec and your motormounts?
The bolts for the motor mounts were dictated by the threads that were already in the side of the Ecotec motor. If I remember correctly they were 12mm x 1.25mm.
I have a bit of a fumb question but shouldn’t the motor be held by something other than the transmission?
In another video I tie the motor mounts in to the rear cage. In this video the rear cage is not in place.
Hey Mike, hope you don't mind I have recommended your channel to a couple people, it would be a shame for someone that's in to Baja's not to be able to enjoy your work!
Heck yeah man, spread the word. lol
Hey Mike, I know you stand behind Lincoln welders so I have been spending a lot of time looking at the Lincoln 210 mp, the reviews on the stick and mig are really good, the tig seems to be ok, but I guess you have to wire up the foot pedal, but i'm ok with that.i have a couple of questions I see that most of the time I am seeing gas with the mig welding is that when you don't have flux core wire or do you always need gas to weld mig, and do you recommend gas? and my other question is can you mig and tig aluminum with this machine. thanks Mike
That welders tig process is not AC, so it won't do aluminum. Don't buy it. You really have to step up in the welders to get AC tig. You will really need two welders. One for mig and one for tig. The benefit is you can get the mig now and in a couple years if your fab skills are still growing you can get an AC tig and start tigging aluminum.
www.homedepot.com/p/Lincoln-Electric-180-Amp-Weld-Pak-180-HD-MIG-Wire-Feed-Welder-with-Magnum-100L-Gun-Gas-Regulator-MIG-and-Flux-Cored-Wire-230V-K2515-1/100670932
For the money I think that is the best Lincoln welder for Mig. It will do mig or flux core. If you do mig you will need gas. The gas will be a mixture of Argon and CO2. If you do flux core you wont need any gas.
The Lincoln Square Wave Tig 200 is a good choice for a garage tig welder that will rock and roll aluminum. For tig you will need 100% Argon for your shielding gas. Almost any tig welder will stick weld as well.
Of course there are no name brand welders for a fraction of the price. That's up to you. They are likely fairly good. All I can say is both of my welders are 20+ years old, local supply houses support them. And when I go out into the garage both of those welders look at me and say "what are we welding today"!
Mike , right now I have a brand new Chicago .stick welder and a new dual mig, I bought both from my neighbor for 150, they both came with carts, rod ,wire, helmet, and and a big fat book on everything you need to know about welding. Mike I couldn't pass this up for the price, these are only temporary, I will be getting much better quality stuff soon. would you agree this is a good way to practice on small welding to sorta get the hang of it. I have already built a little dog for my wife and I had a blast doing it. now I know why its called stick welding, but after a while I was going along pretty good, then it got fun. again these cheap welders are only temporary! Now time for another episode of Doug Bug
Mike that's perfect! A great way to dip into the waters and test some stuff out, for $150 that's a steal. Now you can fiddle around and casually look at an upgrade if you decide to go that route.
Did you run a thermostat and how did you get the air out of your system
I don't run a T-stat on this engine. The temperature is controlled by the electric fans on the radiator. I got the air out using a plug as a bleeder on the leaving port for the radiator line up near the valve cover.
Do you know which Eco-Tec is the best for a Baja Bug / Buggy swap? And is a 2.5 a good choice? Thank you,
My favorite is the LE5 block with the VVT. The VVT really helps with low end torque. It reminds me of the old Honda XR bikes. They growl at the low end, but keep chugging along. Mine is an LE5 and it came from a 2007 Cobalt.
Great videos. I think it's crazy that the adapter costs twice as much as the engine! How hard would it be to build your own adapter, to keep it really cheap? You just tripled your budget!
Yeah I agree. We need a couple million more people to start buying these adapters to drive the costs down. I don't have machine tooling big enough to make anything like that. Otherwise I would.
Thanks for the comment bud.
It’s a ton of work.
Awesome video, thank you for taking the time to post it. Was the flywheel modified at all to fit the VW transmission/clutch/pressure plate or does it happen to work for that particular swap?
Thorvald Moen, This flywheel comes with the kit and is machined to fit the VW transaxle with 200mm flywheel. So on one end it is machined just like a VW flywheel and on the other end it is machined to mate with an Ecotec 6 bolt crankshaft, and when it it designed/machined the proper offsets are put in it.
I paid a little extra to have it lightened, but that didn't affect any of the fitment.
I hope that answers your question.
Doug Bug Yes it does answer my question, thank you. I look forward to the next video!
Hello have you had any problems with running to 10 degree mount
Nope, the oil returns just fine, and no problem with oil pressure either. Every time I have the valve cover off the timing chain looks like it's getting plenty of oil too.
I will say I do keep it up to the top on the dipstick. And leaned back that's a bit of extra oil. But I haven't had any issues.
this may be a silly question but what is the downfall for putting a ecotec motor or any motor in a sand rail with its original transmission?
The downfalls would be that the stock transmission isn't really meant for that kind of power. So it makes the likely hood of breaking the transmission really high.
I would stay focused on keeping whatever ground clearance you have due to future losses with some type of skid plate protection. Also center of gravity and overall balance something to keep in mind. Nothings perfect and you have the skills to change things later. I enjoy your thought process
Hey EZGZ, You are right. My first plan is to look into the oil return in the head of the motor. I don't want to change the angle. I like it and it helps with the tail draggi'n. I just need to make sure the oil can drain out of the head.
Doug Bug You'll be fine, just run it! Don't over think it
What did this motor come out of?? And what year
It came out of a 2007 Cobalt SS. This engine is the 2.4L LE5 with the E67 ECU.
Do you need to build motor mounts or can it ride like the old motor
It definitely needs motor mounts. To heavy to just hang off the transaxle.
ua-cam.com/video/d2PCkDrysQg/v-deo.html
did you make your own brackets to pick the ecotec engine up?
No, the brackets I used were on the engine in the chevy Cobalt when I picked it at the junkyard. I used those to set it in the chassis as well. Then once it was in there I unbolted them.
Hey question what type of suspension kit did you use in the Baja bug
No kit, I build the suspension from scratch.
@@DougBugBuilder awesome my boy and I wanna build or get a long A-arm kit like that let him get use to it and then put a bigger better motor in it
what transmission do you have?
Right now it's a VW Bus type 2. It's held up fine, but I'm always a little nervous it's going to break. But I guess time will tell. ;-)
Hello, what starter are you using?
This is the stock VW starter. It bolts in the original location and everything. The Ecotec has a provision for a starter. But with the adaptor flywheel you retain the original starter in the original location in the VW transaxle.
So what transmission is in this thing?
This has the Bus type 2 in it. Or as it's called the 3 rib with the 5.37 R&P.
What transaxle are you using?
Bus type 2 with 5.38 R&P.
Doug Bug. I am doing a engine swap in my Baja. My engine is a Mitsubishi Lancer 2.0 only because own the car where I don't have to buy another engine. Wondering if you can help me about the ECM. Do you know if the place how did your do other car manufacturers ECMs?
I'm checking with them, I'll let you know what they say.
Doug Bug. Thanks!! What did you use to hold your fenders on with? You drilled a hole and insert the peace in & the tool name. I'm going to get some of them. You didn't mention what they wear in your video. Thanks for all the video's you are very good!
David, Throse are called rivit nuts. Here is an example of a kit similar to mine.
amzn.to/2BmCzLF
The rivit nuts I used on those fenders were 5/16-18.
The tool I used is an industrial one from McMasterr Carr. It was like $180. But the link I gave you there is for a similar one just not as industrial. The choice is yours. ;-)
Make some test sets first to get comfortable with it before you drill into the bug. Once you get the hang of it they are great though.
I don't know why you didn't use a Mazda rotery engine, you wouldn't be having these problems.
Didn't even think about that, a rotary would be a pretty cool motor to hang off the back there. I guess the answer is because I don't have any experience with the rotary motors.
Don’t know how to reply back to you . You will be ok with the motor slightly tilted
Cali Coca, Thanks bud, I am still going to monitor the oil return just to be safe. If needed I can add a drain line at the rear of the head back into the oil pan. But with you saying it should be ok I'm going to just keep an eye on it.
You can always email me direct at dougbugbuilder@gmail.com.
Thanks.