Bob. You rock. I wish I would have known this when just weeks after getting my bike the pedal fell of and the belt misaligned. IFIT replaced the belt but it was all problems from there. I’m 160 pounds, ride 3 times a week for the last year and this problem I just fixed due to your video makes my bike feel brand new. It’s the tight smooth ride I expected. Mine had gone on so long that the bearings inside were busted up and the old casing was shaving off. If you take your cover off and you see metal scraps and have the sound and grinding it’s likely the cheap stock they put in. A little tip if you can’t get your left pedal shaft cover with the tiny hex off and it has stripped out. Get a drummer tool, metal blade and cut a slot over the hex insert so you can use a screwdriver to loosen and take off the left crank. That’s why I had to put up with the worn out grinding on the bike because I could not get the pedal off to see the damage. Thanks so much for your video.
Also Amazon had the part but it was 5 days. I just called my local bike shop and they had the exact part for the same price. I bought the tool, it’s critical to get it off on put it on right. Putting the belt on and off I just hooked the front first then started the belt on the back in the groves and just turned the pedals to force it on.no problems and I don’t have to mess with the tighten loosen mechanism
Bob I appreciate your video. My only suggestion is you could mention socket and wrench sizes. I am headed over to the in-laws, they are tool challenged so I will have to take the whole toolbox to ensure I have the correct tools. Just some feedback, your video was very helpful. I really like the tape on the socket trick. Thanks so much!
This video was very helpful. Thank you for the recommendation of Shimano bearing. The only difference between my experience and your video was getting the old bearing off took a lot of effort. Was not as easy as you showed it. Might be due the first assembly. I paid for professional assembly. Putting the belt back on was a bit of a challenge too.
Thank you so much for doing this video, Bob. Even if the bearings on my S22i did not need changing, I would switch them for the Shimano for the smoothness and peace of mind.
Thank you so much. I followed your instructions and replaced the bottom bracket on my S22i with the new Shimano like you recommended. When I removed the original bracket it was in pieces inside and ground up.The difficult part was removing the belt and putting it back on. Make sure that you align the belt right in the middle and that the spin wheel is centered right over the magnet so it doesn’t scrape on the sides. Otherwise brilliant instructions. My bike does not make one sound. The crank assembly moves like butter.
What a great video. It's terrific you had the patience to show everyone how to replace the bearing. Also you indirectly exposed how NordicTrack/iFit chose to spend $10 less to use an inferior bearing to increase their profit margin rather than to provide a higher quality product. I mean when everyone's cheap bearing fails who's going to want to spend money on all the tools you used to do what you accomplished?
Great video. Was having noisy bearings after four months, found this, and with a few hours work got it smoother than ever. Thanks, very well done, took a bit longer for me as I had tried to grease the shaft, and that made it too tight to turn etc, so had to take the crank shaft back out and clean off the grease and just let it ride on the new bearings.
My s22i was making an intermittent click and pedaling seemed to be rough. After combing through iFit/NordicTrack Facebook pages it was suggested the bottom bracket bearings may be bad. I searched on You Tube and found this video. I ordered the suggested parts and after following the video we were able to easily change the bearings and it makes a HUGE difference. When we took them off, nothing looked wrong to the eye, but the quality is much better with the Shimanos. Thanks for the great video!!!
Thank you so much for taking your time to produce this very, very helpful video instructing how to replace the Bottom Bracket bearings. My S22i has 3000 miles on it, so I am replacing the Flywheel Assembly bearings at the same time. It would have been nice to have a video to walk through this process, too. Thanks again!
Thank you so much for this video. Grinding noise in my wife's S22i and in trouble shooting, I noticed a couple balls popped out of the bearings. I will be following this closely to do the repair.
This is the best video out there! I have a Nordictrak 10i commercial bike I bought 4 years ago! About a month my bottom bracket completely disintegrated I was out 3 weeks.. voila! Found this video! Buy the shimano BB he recommends!! I bought it on Amazon! In case I needed to return it! No problem.. it worked!! Thanks Again!!!!
Excellent video. Thanks for making it. This may others - my bike belt still had tension even with the flywheel adjusted to maximum slack. Had to use a couple of levers to force it back on. In my case, I used some plastic auto trim removal tools to wedge the belt back into place
@@paulshapiro6119 thank you so much for confirming, Amazon doesn’t currently seem to have the ones ordered in the video so I did some research and hoped this would work.
Thanks for making this clear, concise and to the point video, also thanks for recommending those bearings. Definitely going to buy them now. Will subscribe. God Bless
Great video. I’m experiencing clicking and can’t figure out if it’s the Candy pedals, shoe clips, or bottom bracket. Knowing how easy the bottom bracket is to change this might be the next replacement.
I replaced my bottom bracket bearing due to a knock. Still have knock but it sounds like it is coming from front wheel. I messed with tension discrete but didn’t mark them like you suggested. I am having a hard time getting them adjusted correctly. Do you have a measurement of amount of bolt thread length after nuts are tight? Any suggestions?
On my S22i there is a plastic bearing top hat that fits between the crankshaft and the bearing. I didn’t see that in this video. Does the SHIMANO bearing require this plastic top hat piece?
My bearings were bad the first day of owning the bike, kinda upset about that. They’re sending a tech out to fix though. I bought the shimano bearings and the removal bit but I’ma let them fix it. Video is saved for the future though. Thanks
I replaced the bearing yesterday, but the front wheel developed a nasty squealing noise just prior to my replacing the bearing and it did not go away . Any ideas on the cause?
For the 22i the bearing specification is BC1.37x24T This is a British standard for Bottom Bracket Bearings - not Italian 70mm. There are several bearing sets that are available that meet these standards. I was advised to avoid ceramic bearings because they fail. I have had my 22i since 2019 with daily use. This is my first adventure replacing the bottom bracket bearings.
@@jeremiegrund Any 68mm english threaded bottom bracket spec'd for a 24mm spindle will work. The OEM bottom bracket has a 44mm cup size which is the size of the tool used to take off the bottom bracket shown in the video. The bottom bracket I bought had a smaller cup size than the original one but it still fits on the frame because the threading and width are the same. It's hard to find the larger 44mm bottom brackets now since it looks like most manufacturers have gone to a smaller size.
How did you take the right side plastic cover off? I tried following what you did in your video but am unable to fully remove it. I was able to replace the bottom bracket with the Shimano one but I can feel tension when I pedal, what do you think might be causing it?
Thanks for sharing the step by step instructions. This video was very helpful. I am still wondering how can this $2000 worth commercial grade studio cycle come with such cheap parts. My S22i has not even done 100 miles. I had to replace this bottom bracket. I have very similar experience with Nordictrack top of the line commercial 2950 treadmill. Never buying a Nordictrack again. It is just waste of time after spending hefty money.
I actually wonder if it could be argued that using the term "commercial" might be legally misleading. No commercial facility would use cheap parts on the main points of failures - would use highest quality bearings.
I have to order a new bearing for my s22i. I had the bearing replaced with ones NordicTrack had sent me like 2 years ago. My bike is like almost 4 years old. Do you think these bearing will last longer?
The NT bearing is crap. It can be purchased online for ~$10-15 (or of course, going through NT). If you are doing the work yourself I suggest upgrading to a better compatible bearing ~$40 (if I recall correctly). Labor is really the main expense, not complex...but kind of tedious job (but not too bad).
So I did the exact same thing as you as I was having grinding issues. That has now gone away, but im getting a quick vibration in the handles around 80rpm. Im able to pedal out of it, and it will stop. Im wondering if I overtightend my belt, or something is misaligned. Almost seems like the flywheel has a wobble in it when I try to maintain a constant rpm. Did you have any issues such as this? Is there a spec for tightening the belt? I cant seem to find anything
Really helpful video! I have an S10i and have same issue. Do you know the shimano part number for an S10i? Is it the same? Also, I need to be able to purchase the part in the UK.
Thanks. I have no idea if they are the same. I'm guessing it might be because the frames are similar. I bought my part off of Amazon in the US, but the bearing manufacturers are pretty much global.
I can't get either bearing loosened, anyone have a suggestion to get them off. I'm trying WD-40, letting it sit overnight and will try again tomorrow. The Park tool keeps slipping off the bearing as well.
Purchased the Park Tool BBT-69.2 but it is too small and does not fit on the bearing? No idea why any advice other than just buy a larger model? It is 44mm
What kinda noise did you hear to diganoise that it was the bottom bracket? I have a scrapping noise when i pedal backward and forward. It sounds like its coming from that area, but I'm not sure. IFIT warranty/rma is taking forever to communicate with.
@@bobkrueger194 sounds like my issue. Just got my bike this year and was first having issus with the seatpost noise while riding. Nordic sent me a new one. Now, whenever i pedal at the same spot/oritenation of the pedals there is a scrapping noise. Took off both black covers on each side and still hear the scrapping noise. Its not bad, but going to change it out to that same shimano part! Thanks for the instructions! It's a real shame the bottom bracket it comes with is a cheap brand. How's your bike doing after the 1 year replacement ?
@@bobkrueger194 Thank you so much! just installed my bottom bracket. smooth as butter. makes me love riding the bike again. Curious, How long has yours been holding up for?
Has anyone had a problem with the front flywheel on the S22I squeaking intermittently when pedaling? I replaced the bottom bracket bearing, but it started squeaking just a few days before I replaced the bearing.
Looking at doing this because I’ve got a BB-R9100 laying around, but it looks like the bracket diameter is smaller on the 9100 than the factory brackets. The inside diameter appears to be the same, did that work for you?
I've only had my s22i since July and I am now hearing what I can describe as rubber bands turning when I first move the crank. When I am peddling I hear a noise that is hard to describe. Is this what you experienced?
The flywheel might be slight off center. I had that noise and I think it was unrelated to the bottom bracket bearings being broken. I looked at the pulley and it had a lot of junk built up rubber in the grooves that I cleaned out with a small flat head screwdriver. It doesn't make the rubber band noise anymore.
I recommend not taking pedal off crank if you don't need to (if it is not damaged or loose) as the hardware holding the pedal to crank is really flimsy (and specialized). It would be awful to damage the threads unnecessarily.
What about the front wheel? I had mine replaced when it was still under warranty and now it’s getting noisy again 😞 I suppose there’s no way to just get bearings for that?
Yes, actually they're very simple to replace! The link below are the bearings you need. Timken 6300-2RS. They're not pressed in hard at all. When you re assemble, put some green locktite on the spindle where it passes through the bearing sleeve to keep it all in place. www.motionindustries.com/products/sku/07408316?gclid=Cj0KCQjw_dWGBhDAARIsAMcYuJwltWXrYu3dXzJy0vQ7MDNJL33R3oV_SI37cSctvcbWx7sc3utdRdwaAhSaEALw_wcB
Hi could you help me please. I replaced the bearings but now the belt tension seems way too hard and I notice the fly wheel is hitting the left side of the magnetic resistance magnet. It's literally rubbing/stuck next to it. What can I do? I really need your help.
Hi Bob, do you have the Shimano Part number? There appears to be a BSA (and non-BSA) version. I am assuming they may be different threads? I am looking at the BB-RS500 on Amazon. Thanks and great video, thank you!
@@paulshapiro6119I’m experiencing a great deal of resistance trying to get the spindle (right crank) through the BB R9100. Did you experience resistance? If so, how did you get it through?
They charge $100-$120 for the OEM bottom bracket on these bikes. Insane that you can get a much higher quality bracket for $20-$40. The build quality of these bikes stink. Major parts replacement at least once a year. I've already replaced the resistance motor and now the bottom bracket. The incline motor is probably next.
The manufacturer bottom bracket on these bikes is "Gineyea BB51" and ND parts distributors are trying to sell this $8 bottom bracket for $120. Definitely get the park tool to remove. I had to use an impact to take off one side because it was not lubricated at the factory and was essentially rusted onto the frame. I replaced it with a Shimano Dura Ace BB-R9100
Great vid! I just made the same change, 100% better. They should ditch the free toe strap pedals and invest in this bottom bracket for their bikes. I swapped the pedals with clipless, way better. Now as smooth as my $8K mtb.
Bob. You rock. I wish I would have known this when just weeks after getting my bike the pedal fell of and the belt misaligned. IFIT replaced the belt but it was all problems from there. I’m 160 pounds, ride 3 times a week for the last year and this problem I just fixed due to your video makes my bike feel brand new. It’s the tight smooth ride I expected. Mine had gone on so long that the bearings inside were busted up and the old casing was shaving off. If you take your cover off and you see metal scraps and have the sound and grinding it’s likely the cheap stock they put in. A little tip if you can’t get your left pedal shaft cover with the tiny hex off and it has stripped out. Get a drummer tool, metal blade and cut a slot over the hex insert so you can use a screwdriver to loosen and take off the left crank. That’s why I had to put up with the worn out grinding on the bike because I could not get the pedal off to see the damage. Thanks so much for your video.
Also Amazon had the part but it was 5 days. I just called my local bike shop and they had the exact part for the same price. I bought the tool, it’s critical to get it off on put it on right. Putting the belt on and off I just hooked the front first then started the belt on the back in the groves and just turned the pedals to force it on.no problems and I don’t have to mess with the tighten loosen mechanism
Bob I appreciate your video. My only suggestion is you could mention socket and wrench sizes. I am headed over to the in-laws, they are tool challenged so I will have to take the whole toolbox to ensure I have the correct tools. Just some feedback, your video was very helpful. I really like the tape on the socket trick. Thanks so much!
This video was very helpful. Thank you for the recommendation of Shimano bearing. The only difference between my experience and your video was getting the old bearing off took a lot of effort. Was not as easy as you showed it. Might be due the first assembly. I paid for professional assembly. Putting the belt back on was a bit of a challenge too.
Thank you so much for doing this video, Bob. Even if the bearings on my S22i did not need changing, I would switch them for the Shimano for the smoothness and peace of mind.
Thank you so much. I followed your instructions and replaced the bottom bracket on my S22i with the new Shimano like you recommended. When I removed the original bracket it was in pieces inside and ground up.The difficult part was removing the belt and putting it back on. Make sure that you align the belt right in the middle and that the spin wheel is centered right over the magnet so it doesn’t scrape on the sides. Otherwise brilliant instructions. My bike does not make one sound. The crank assembly moves like butter.
What a great video. It's terrific you had the patience to show everyone how to replace the bearing. Also you indirectly exposed how NordicTrack/iFit chose to spend $10 less to use an inferior bearing to increase their profit margin rather than to provide a higher quality product. I mean when everyone's cheap bearing fails who's going to want to spend money on all the tools you used to do what you accomplished?
Great video. Was having noisy bearings after four months, found this, and with a few hours work got it smoother than ever. Thanks, very well done, took a bit longer for me as I had tried to grease the shaft, and that made it too tight to turn etc, so had to take the crank shaft back out and clean off the grease and just let it ride on the new bearings.
My s22i was making an intermittent click and pedaling seemed to be rough. After combing through iFit/NordicTrack Facebook pages it was suggested the bottom bracket bearings may be bad. I searched on You Tube and found this video. I ordered the suggested parts and after following the video we were able to easily change the bearings and it makes a HUGE difference. When we took them off, nothing looked wrong to the eye, but the quality is much better with the Shimanos. Thanks for the great video!!!
Thank you so much for taking your time to produce this very, very helpful video instructing how to replace the Bottom Bracket bearings. My S22i has 3000 miles on it, so I am replacing the Flywheel Assembly bearings at the same time. It would have been nice to have a video to walk through this process, too. Thanks again!
Thank you so much for this video. Grinding noise in my wife's S22i and in trouble shooting, I noticed a couple balls popped out of the bearings. I will be following this closely to do the repair.
This is the best video out there! I have a Nordictrak 10i commercial bike I bought 4 years ago! About a month my bottom bracket completely disintegrated I was out 3 weeks.. voila! Found this video! Buy the shimano BB he recommends!! I bought it on Amazon! In case I needed to return it! No problem.. it worked!! Thanks Again!!!!
67.8mm ~ 68mm measurement on the bb nice to know! Awesome that you measured with a caliper and posted that thanks!
Excellent video. Thanks for making it. This may others - my bike belt still had tension even with the flywheel adjusted to maximum slack. Had to use a couple of levers to force it back on. In my case, I used some plastic auto trim removal tools to wedge the belt back into place
Really great video. I knew there had to be a better BB available for this bike but wasn’t willing to sit in hold for an hour to get the information
very helpful indeed. Got the bearings upgraded to Shimano on mine so hoping for a better ride from it. Thanks so much!
Yes, I added Shimano Dura Ace bearings. I wish I had viewed this video first. Video instructions look perfect to me.
@@paulshapiro6119 do you recall the part number on the bearing that you used?
@@paulshapiro6119 I just ordered a BB-R9100 and I’m trying to determine if they are compatible
@@jeremiegrund @Jeremie Grund Yup, SHIMANO Dura-Ace BB-R9100 Bottom Bracket is also what I used. Working great!!!!
@@paulshapiro6119 thank you so much for confirming, Amazon doesn’t currently seem to have the ones ordered in the video so I did some research and hoped this would work.
Great Video! Thanks for making this I'm starting to feel the bearings going in mine and was looking into replacing them soon.
Thanks for making this clear, concise and to the point video, also thanks for recommending those bearings. Definitely going to buy them now. Will subscribe. God Bless
Thanks, the Shimano BB-RS500 68mm was a perfect fit.
Someone recommended this one to me too, just ordered it. Seems like nordictrack took some shortcuts and cheaped out on this expensive bike.
Great video. I’m experiencing clicking and can’t figure out if it’s the Candy pedals, shoe clips, or bottom bracket. Knowing how easy the bottom bracket is to change this might be the next replacement.
I replaced my bottom bracket bearing due to a knock. Still have knock but it sounds like it is coming from front wheel. I messed with tension discrete but didn’t mark them like you suggested. I am having a hard time getting them adjusted correctly. Do you have a measurement of amount of bolt thread length after nuts are tight? Any suggestions?
That was a great help. Thank you
On my S22i there is a plastic bearing top hat that fits between the crankshaft and the bearing. I didn’t see that in this video. Does the SHIMANO bearing require this plastic top hat piece?
My bearings were bad the first day of owning the bike, kinda upset about that.
They’re sending a tech out to fix though. I bought the shimano bearings and the removal bit but I’ma let them fix it. Video is saved for the future though.
Thanks
I replaced the bearing yesterday, but the front wheel developed a nasty squealing noise just prior to my replacing the bearing and it did not go away . Any ideas on the cause?
Thanks for putting together this video. Perfect instructions for the S15i, too. Easy to follow and the ride is so much better and quieter.
For the 22i the bearing specification is BC1.37x24T This is a British standard for Bottom Bracket Bearings - not Italian 70mm. There are several bearing sets that are available that meet these standards. I was advised to avoid ceramic bearings because they fail.
I have had my 22i since 2019 with daily use. This is my first adventure replacing the bottom bracket bearings.
Are you saying the shimano bearing in the video isn’t a correct match? Do you have a part number of one more recommended?
@@jeremiegrund Any 68mm english threaded bottom bracket spec'd for a 24mm spindle will work. The OEM bottom bracket has a 44mm cup size which is the size of the tool used to take off the bottom bracket shown in the video. The bottom bracket I bought had a smaller cup size than the original one but it still fits on the frame because the threading and width are the same. It's hard to find the larger 44mm bottom brackets now since it looks like most manufacturers have gone to a smaller size.
Thank you so much for this video!!!
How did you take the right side plastic cover off? I tried following what you did in your video but am unable to fully remove it. I was able to replace the bottom bracket with the Shimano one but I can feel tension when I pedal, what do you think might be causing it?
Great video. What was the noise to determine that this was a bearing issue vs belt issue?
They just were not smooth. Seemed a bit gritty. New bearings are fantastic yet
How did you get the drive shaft through the left side bearing without it busting out the plastic bearing shield?
I’ve had the same problem.
Thanks for sharing the step by step instructions. This video was very helpful.
I am still wondering how can this $2000 worth commercial grade studio cycle come with such cheap parts. My S22i has not even done 100 miles. I had to replace this bottom bracket. I have very similar experience with Nordictrack top of the line commercial 2950 treadmill. Never buying a Nordictrack again. It is just waste of time after spending hefty money.
I actually wonder if it could be argued that using the term "commercial" might be legally misleading. No commercial facility would use cheap parts on the main points of failures - would use highest quality bearings.
I have to order a new bearing for my s22i. I had the bearing replaced with ones NordicTrack had sent me like 2 years ago. My bike is like almost 4 years old. Do you think these bearing will last longer?
The NT bearing is crap. It can be purchased online for ~$10-15 (or of course, going through NT). If you are doing the work yourself I suggest upgrading to a better compatible bearing ~$40 (if I recall correctly). Labor is really the main expense, not complex...but kind of tedious job (but not too bad).
So I did the exact same thing as you as I was having grinding issues. That has now gone away, but im getting a quick vibration in the handles around 80rpm. Im able to pedal out of it, and it will stop. Im wondering if I overtightend my belt, or something is misaligned. Almost seems like the flywheel has a wobble in it when I try to maintain a constant rpm. Did you have any issues such as this? Is there a spec for tightening the belt? I cant seem to find anything
Really helpful video! I have an S10i and have same issue. Do you know the shimano part number for an S10i? Is it the same? Also, I need to be able to purchase the part in the UK.
Thanks. I have no idea if they are the same. I'm guessing it might be because the frames are similar. I bought my part off of Amazon in the US, but the bearing manufacturers are pretty much global.
What tool were you using to remove the left crank as I am having trouble removing mine?
Two different sized allen or hex wrench keys. I can post the sizes for you if needed. Let me know
Thank you for your response. Yes please post the size. 😊
I can't get either bearing loosened, anyone have a suggestion to get them off. I'm trying WD-40, letting it sit overnight and will try again tomorrow. The Park tool keeps slipping off the bearing as well.
Purchased the Park Tool BBT-69.2 but it is too small and does not fit on the bearing? No idea why any advice other than just buy a larger model? It is 44mm
Sorry. Just saw this. Did you get it resolved?
What kinda noise did you hear to diganoise that it was the bottom bracket? I have a scrapping noise when i pedal backward and forward. It sounds like its coming from that area, but I'm not sure. IFIT warranty/rma is taking forever to communicate with.
It just wasn't smooth. Kind of gritty. The Shimano is awesome.
@@bobkrueger194 sounds like my issue. Just got my bike this year and was first having issus with the seatpost noise while riding. Nordic sent me a new one. Now, whenever i pedal at the same spot/oritenation of the pedals there is a scrapping noise. Took off both black covers on each side and still hear the scrapping noise. Its not bad, but going to change it out to that same shimano part! Thanks for the instructions! It's a real shame the bottom bracket it comes with is a cheap brand. How's your bike doing after the 1 year replacement ?
@@bobkrueger194 Thank you so much! just installed my bottom bracket. smooth as butter. makes me love riding the bike again. Curious, How long has yours been holding up for?
Has anyone had a problem with the front flywheel on the S22I squeaking intermittently when pedaling? I replaced the bottom bracket bearing, but it started squeaking just a few days before I replaced the bearing.
I replaced mine 13 months ago with Shimano Dura Ace BB-R9100 also.
nice to know there are alternatives. Would like to upgrade to BB-R9100 when mine goes out.
Looking at doing this because I’ve got a BB-R9100 laying around, but it looks like the bracket diameter is smaller on the 9100 than the factory brackets. The inside diameter appears to be the same, did that work for you?
@@tdavis197 been riding my s22i for over year with Shimano Dura Ace BB R9100. Works perfectly.
@@paulshapiro6119 do you know the diff between the 9100 and the rs500 ? Thx
@@sjames3819 Nope
I've only had my s22i since July and I am now hearing what I can describe as rubber bands turning when I first move the crank. When I am peddling I hear a noise that is hard to describe. Is this what you experienced?
The flywheel might be slight off center. I had that noise and I think it was unrelated to the bottom bracket bearings being broken. I looked at the pulley and it had a lot of junk built up rubber in the grooves that I cleaned out with a small flat head screwdriver. It doesn't make the rubber band noise anymore.
What do you suggest if the right bearing is too tight to remove? Left came off easily, right bearing, not so much. Thanks
Soak with some penetrating oil. What kind of hex wrench you using? Might need to be something with a sizable handle.
This is the same issue I’m having right now. My left side won’t budge. Did you get this sorted out?
Where do I get those bearings?
Most bike shops or on line at Amazon
@@bobkrueger194 how do I know the right one to get though? I’m sure there are different versions? Sorry, thanks for info.
@@FuturesBrizio Shimano BB-RS500 68mm version. UPC 689228926172
@@bobkrueger194 thank you very much!
35-50 newt meters what is that in foot pounds?
I want to order the BB-RS500 68mm but my bike bearing says it’s a 73mm?
They may have changed the size. You might need to measure it to be 100% certain. If you buy from Amazon, returns are easy.
If you are taking off the crank, why did you need to remove the pedal???
i don't recall. Maybe to get it out of the way. i suppose you could leave it on.
I recommend not taking pedal off crank if you don't need to (if it is not damaged or loose) as the hardware holding the pedal to crank is really flimsy (and specialized). It would be awful to damage the threads unnecessarily.
What about the front wheel? I had mine replaced when it was still under warranty and now it’s getting noisy again 😞 I suppose there’s no way to just get bearings for that?
I am sure bearings are replaceable. Have not done that yet though
When they sent their tech the first time he said could only get the whole wheel.
Yes, actually they're very simple to replace! The link below are the bearings you need. Timken 6300-2RS. They're not pressed in hard at all. When you re assemble, put some green locktite on the spindle where it passes through the bearing sleeve to keep it all in place.
www.motionindustries.com/products/sku/07408316?gclid=Cj0KCQjw_dWGBhDAARIsAMcYuJwltWXrYu3dXzJy0vQ7MDNJL33R3oV_SI37cSctvcbWx7sc3utdRdwaAhSaEALw_wcB
Hi could you help me please. I replaced the bearings but now the belt tension seems way too hard and I notice the fly wheel is hitting the left side of the magnetic resistance magnet. It's literally rubbing/stuck next to it. What can I do? I really need your help.
Nevermind I think I figured it out.
Ok. Sorry, I was at a cook out
@@TheBull06 What was your solution? I'm running into the same thing and it's making me crazy
@@crmaximusb I just adjusted the two bolts until the flywheel moved enough to stop hitting the magnetic resistance. I did trial and error.
Hi Bob, do you have the Shimano Part number? There appears to be a BSA (and non-BSA) version. I am assuming they may be different threads? I am looking at the BB-RS500 on Amazon. Thanks and great video, thank you!
Here is the bearing I used.
SHIMANO Bottom Bracket Parts, BB-RS500, Right & Left Adapter(BSA), Bearing a.co/d/brZwJQQ
I used Shimano Dura Ace BB-R9100 Hollowtech II BSA Type Bottom Bracket (13 montha ago).
@@paulshapiro6119I’m experiencing a great deal of resistance trying to get the spindle (right crank) through the BB R9100. Did you experience resistance? If so, how did you get it through?
I am sorry but I don't remember. It has been a few years since I did this and wish I could help more. I hope someone else can assist.
What size are nuts to loosen belt tension?
I think I called it out in the video. I would have to take mine apart to see
Should have said I messed with the tension nuts
They charge $100-$120 for the OEM bottom bracket on these bikes. Insane that you can get a much higher quality bracket for $20-$40. The build quality of these bikes stink. Major parts replacement at least once a year. I've already replaced the resistance motor and now the bottom bracket. The incline motor is probably next.
The manufacturer bottom bracket on these bikes is "Gineyea BB51" and ND parts distributors are trying to sell this $8 bottom bracket for $120. Definitely get the park tool to remove. I had to use an impact to take off one side because it was not lubricated at the factory and was essentially rusted onto the frame. I replaced it with a Shimano Dura Ace BB-R9100
That belt reassembly was way too easy for you.
Great vid! I just made the same change, 100% better. They should ditch the free toe strap pedals and invest in this bottom bracket for their bikes. I swapped the pedals with clipless, way better. Now as smooth as my $8K mtb.
The whole thing is made in China