Hello sir, My sim module doesn't show any response after sending at commands.. My project is gas leakage detection and the gas readings are displayed in serial monitor simultaneously so will that suppress the sim module's response.. please do help me sir 😢.. I am stuck with it for past 3-4 weeks 😭
excuse me sir i am using this gsm 900a for my science project.Actually the problem is that my gsm is not sending SMS to a desired person what should i do
Well that's a very general question. Maybe you can try to spot where the problem is. Go thru part1,2 and 3 to see if you could replicate the same from your end
Hello sir , my gsm 900a is not blinking(D6) . It just glows when it finds the signal(connection). What is the problem? . Is there anyother way to contact you?
Can you please help me? When I enter the AT command like AT and enter, the output becoming "kC⸮ ", do you know why this thing happen? Please help and advise, I am quite upset, because cannot fix this weird output coming out from serial monitor
@@electronicseternity9210 yes sir, all that had been done, changing laptop, mac, pc, and change each baudrate also result similar findings or even worst. Can you please do help me. So far when I call the number from other phone, the serial monitor indicate something, but the value/ character display was not understandable..
@@syaduinotech3681 Tbh, the characters are not understandable for me too. I'd suggest contacting your SIM900 provider. I did the same anytime I need info on my gsm module.
@@electronicseternity9210 thanks sir. Your ideas make sense.. i re do it again, based on your sketch and change one baudrate by one.. until i got mine 38400 and its well done and able to be used. Tq sir.. your response and sharing very much appreciated
Thanks for sharing such an Awesome project. The link shared to download the code is not operational . Please check the link or share the code. Thanks & kind regards.
@@electronicseternity9210 Thanks for your reply. Can I have your email address so I can share the web page which is showing that Content can not be displayed.
if network LED doesn't blink what to do.And only DC-PMR led is on in SIM 900a
Sir please help me... My serial monitor keeps saying
AT
ERROR
AT
ERROR
Hello sir, My sim module doesn't show any response after sending at commands..
My project is gas leakage detection and the gas readings are displayed in serial monitor simultaneously so will that suppress the sim module's response.. please do help me sir 😢.. I am stuck with it for past 3-4 weeks 😭
excuse me sir i am using this gsm 900a for my science project.Actually the problem is that my gsm is not sending SMS to a desired person what should i do
Well that's a very general question. Maybe you can try to spot where the problem is. Go thru part1,2 and 3 to see if you could replicate the same from your end
good day do you have sim900a bulk sms tutorial ? thankyou
Hy big hommie, Can you flash this module? make a tutorial please, i can't flash it.
Hello sir , my gsm 900a is not blinking(D6) . It just glows when it finds the signal(connection). What is the problem? . Is there anyother way to contact you?
Probably not enough current. use 2 different power sources. One for Arduino and one for GSM and don't forget to link Ground between Arduino and GSM.
Can you please help me? When I enter the AT command like AT and enter, the output becoming "kC⸮
", do you know why this thing happen? Please help and advise, I am quite upset, because cannot fix this weird output coming out from serial monitor
Have you tried varying the Serial Monitor configuration and see how the outcome varies.
@@electronicseternity9210 yes sir, all that had been done, changing laptop, mac, pc, and change each baudrate also result similar findings or even worst. Can you please do help me. So far when I call the number from other phone, the serial monitor indicate something, but the value/ character display was not understandable..
@@syaduinotech3681 Tbh, the characters are not understandable for me too. I'd suggest contacting your SIM900 provider. I did the same anytime I need info on my gsm module.
@@electronicseternity9210 thanks sir. Your ideas make sense.. i re do it again, based on your sketch and change one baudrate by one.. until i got mine 38400 and its well done and able to be used. Tq sir.. your response and sharing very much appreciated
@@electronicseternity9210 thanks so much, please allow me to share your video to my students and friends. Tq sir
Thanks for sharing such an Awesome project. The link shared to download the code is not operational . Please check the link or share the code.
Thanks & kind regards.
Not sure what you mean by not operational. The code is functional from my end. Maybe can share more info on your issue ;)
@@electronicseternity9210 Thanks for your reply. Can I have your email address so I can share the web page which is showing that Content can not be displayed.
@@yawarsaeed6499 You can reach me thru my FB page. All my contact details are there :)