CO2 Laser Air Assist - Installing Electronic Pneumatic Valve
Вставка
- Опубліковано 16 лип 2024
- In this video I will be installing a 24v Electronic Pneumatic Valve in an OMTec h 60w CO2 Laser. The benefit of this valve is to have control over your air assist in the Lightburn Software. I have listed the parts used in the links below. Please remember to **UNPLUG YOUR LASER MACHINE BEFORE ATTEMPTING ANYTHING YOU SEE IN THIS VIDEO**!!!
24 Volt Pneumatic Air Valve: a.co/d/09SwOhN
Terminal Block for Ruida Controller: a.co/d/6vKWy2H
Rectifier Diodes: a.co/d/8rZt6il
6mm Tube and Fittings: a.co/d/5tkNy3D
OMtech CO2 Laser Machine:
The information provided on this channel is for entertainment purposes only. Any action you as the viewer takes upon the information on this channel is strictly at your own risk, and I will not be liable for any losses, damages, or personal injuries in connection with the use of this content (including injuries, damages, or losses sustained while you were trying to emulate the actions and projects on this channel). Attempting to emulate any of the actions or projects put forth by this channel should not be done without training and even then, at your own risk. - Навчання та стиль
I like this idea. Will do it 👍
Thank you 🙏
I think that you need a small amount of air at all times to protect the lens in your machine. I have seen a small bleed bypass valve put in with a T adapter. The other way is to get another valve like you said on the status pin ether way you need a little bleed valve to protect the lens. looks like a great machine hope you have the best of luck with it.
I started out with a eBay Chinese K40, it was the most basic machine and had no air assist. I used this machine for quite some time until I added an air assist. I would have to clean the lens once in a while, but it didn’t fail. There are some jobs I still do today that I can not use any air assist with because it will adversely effect the engraving on that specific material.
Off. A little 24 volt and wind gust is the trigger not ground ,
Fat fingers 24 volt and wind is trigger not ground
Ok, this is great information, just what I was looking for.
But you might want to look at the HUGE volume change between your talking and the intro music. Does it really need to have such a huge increase? When the volume is high enough for your speech at the start it nearly bursts your eardrums when that intro base cuts in.
I just played it on the UA-cam app and there is no volume difference as you have stated.
At any point where you using the compressor instead of the stock air assist at all times without all the hookups and running it at all times?
I used the stock air assist when I first got the laser, and I did not like it. Wasn’t powerful enough for cutting in my opinion. I had a smaller laser that was connected to my air compressor with a ball valve, I manually turned the air on when needed. At first I just hooked up my OmTech that way, but quickly decided to use the options on the software and the control board to make the air assist work as it should with my larger air compressor. My on board air assist is still in the unit, but I put it on a switch and leave it turned off.
@@mw3designs Thank you for getting back to me on this. My stock air on my 60 w Chinese laser died and I want to upgrade to a compressor for air assist but am a bit intimidated by the electronics of it all. My plan was to hook it up and manually turn it on and off with a set PSI for now.... With the plan of tying it in to the machine for control later. Thanks again!
On my smaller laser the air assist was manual like I stated and I used it that way for years. I put an air line with regulator right next to the laser with a 1/4” ball valve right next to the laser, I would turn on the air and send the job. You should have no problems doing it that way, and it’s all user preference, not everyone does it the same.
What is the point of the diode? I don’t think I’ve seen any one else use it?
The diode would eliminate any electrical back-feed to the controller.
@@mw3designs then just use 24 v supplay from power supplay directly not from controler ..