Omron M2 Basic - Teardown
Вставка
- Опубліковано 15 лют 2015
- We take a look inside this Blood pressure monitor by Omron.
This is they type you may find at the doctors surgery.
It has a fault with what I believe is a solenoid responsible for deflating the cuff after measurement has been taken. This is causing the cuff to stay inflated slightly or for it to not inflate at all.
------------------------------------------------------------------------
SOME TECHNICAL INFO
Product Description Digital Automatic Blood Pressure Monitor
Model OMRON M2 Basic (HEM-7116-E/HEM-7116-E8)
Display LCD Digital Display
Measurement Method Oscillometric method
Measurement Range Pressure: 0 mmHg to 299 mmHg
Pulse: 40 to 180/min.
Memory Last measurement
Accuracy Pressure: ±3 mmHg
Pulse: ±5% of display reading
Inflation Automatic by electric pump
Deflation Automatic pressure release valve
Pressure Detection Capacitive pressure sensor
Power Source 4 “AAA” batteries 1.5V or AC/ DC adapter
(optional, 6V 4W)
Battery Life Capacity of new alkaline batteries is approx. 300
measurements
Operating Temperature/
Humidity
10°C to 40°C/ 30 to 85% RH
Storage Temperature/
Humidity/ Air Pressure
-20°C to 60°C/ 10 to 95% RH/ 700-1060 hPa - Наука та технологія
The part you pull out at 3:30 is for over pressure. In case the sensor fails the pump might not stop.
This prevents hoses and the manchet from blowing up too much and eventually rip apart.
I have a similar "solenoid" (?) in the water tank of a robot cleaner, could it be an air pump, that creates a "cushion" of air to expel the water through the nozzles ? where does it draw air from it doesn't seem to have any holes ?
@@gf88888 You don't see it in the video, these pumps have two tubes one at the top and one at the side. The top tube is the outlet and the side is the inlet. Depending on the type you buy the inlet is a tube or flat. The benefit of a flat model is that you can wrap the pump into a soft air passing material which creates a dust filter at the same time while holding the pump in place.
Cool I love the internet, no matter what question normally someone has answered it thankyou
Yes!
Thanks Gareth, we binned it in the end, and purchased a new one, a " choiceMMed model BP11" not sure what you may think of this one???
Kind Regards Dave.
I have an Omron BP-785 that works great. I've used it many times.
At the end, ur still trying to squeeze the cuff as it trying to inflate.
Also, it can sense pulse in ur hands when ur trying to squeeze the cuff when it’s inflating.
The "useless bit" is actually an over pressure release valve, in case it keeps on pumping without stopping.
Thanks, I had realised this my self shortly after
@@ElectronicStuff Is that over pressure release valve always open though?
Hiya, on ours which is now about four years old and hardly ever used! We tried it today and we get an ERROR on the SYS any ideas??
We've hardly used it!
And thanks for the Video,
Dave, Suffolk.
Where does it get the air from since it's all in a shut box? And where does the air go after?
How is the information transmitted from your arm the to the monitor?
I sound silly, but I'm curious.
Today morning I found my OMRON BP742N is dead. It doesn't turn on. Nothing shows on display and not working. I tried with new batteries and using adapter. I didn't even use it more than 10 - 15 times. Are they really junk or what do you think ?
By the way this video is very informative. Thanks for sharing !!
If you think the solenoid is the problem, why didn't you remove it and check it? I've never seen anyone tear something apart before with the batteries still in it.
Does this device needs to be calibrated,?
in pressure sensor there is "KYW9" and in my omron pressure sensor (within HEM-7111 too) is "CMQ9". Is this means something or just a fabrication code?
I buy this six month back but
It’s always showing low battery , after that I replaced with new 4 batteries but still it’s showing low battery only , and automatically off again and again .
I fed up with this product
Can you help me to solve this
Why this is showing low battery
If the machine doesn't compress air(press power and it compresses or sucks air to tighten arm)despite the lcd working fine what could be wrong as the cuff and pipe are okay?Internal error with pump like slit stopper perhaps? What is the slit stopper?
What if the number that appears on the LCD is an error? can't read clearly what number?
Omron bp monitor 7113 using by battery only.How I can fix a jack for use by adapter also?
What is the type of the MCU inside?
I'm guessing the "useless bit" is and over inflation safety valve. Just a guess.
dear sir.... my omron b.p. machine is not able to inflate the puff... kindly help in its repairing... what possibilities are there managing which can help me in repairing it???? kindly reply soon
Hi.. my device HEM-7120, on LCD displayed error E5 when device releasing the pressure. Instead cuff was applied properly at arm. It is indicated on display (OK). Any suggestion to solve this problem?
any solution for a burned omron lcd?
Shouldn't the 'useless bit' the deflating valve? The cuff has to deflate slowly to capture a reading.
still deflates without it, it's a saftey valve (learned this after filming and more reasearch)
i have sanitas sbm 52 with first transistor on vdd cracked and i need part number off this transistor can you help me please
great job bro
error 3 what will be the issue
Good day friend, how can I repair my ALP K2 digital BP monitor that seems to be low on pressure and cannot complete BP monitoring results.
Does anybody know how the readings in the cuff, that is when the blood stops flowing and starting again, is communicated to the monitor? The pressure at these points is obviously measured directly at the monitor which has the pump.
The pressure sensor itself handles that I believe, with heach heartbeat the pressure changes.
the dc power input is with three wires, yellow, brown and grey. does it correspond to brown +6v and grey ground, what about the yellow?
aites, thanks anyway. =)
Hi, Usually (again, I have not checked the actual wire) a DC plug with 3 wires:
- Positive (as you said brown),
- Negative (you found as grey),
- "connect sense" (yellow according to your findings).
The meaning of connect sense means: If you have batteries AND power plug, device disconnects the battery pack and use external power source. This "sense" is usually very simple switch (which open the battery pack circuit mechanically).
Is Hybetez Remedy helpful to treat your high blood pressure issue naturally ? I've read many good stuff about this high blood pressure remedy.
please give me a voltage of cpu and voltage of eeprom thanks
nothing is poinless Omron did not put the over pressure valve in line for nothing, think about it?
It doesn't open THAT easily the first time. This one probably has been opened many times before the video.
I think that white valve you removed, is a pressure valve, incase it over inflates.
Shaun Brown I think you are correct there
The white valve is a solenoid air valve, to release pressure fastly.
If you are interested in mini air pump and solenoid valve used in blood pressure monitor, please contact us.
E-mail: sales01@dyxminipump.com
www.dyxminipump.com
pumpdyx.en.alibaba.com
@@jz7914 I have a similar "solenoid" (?) in the water tank of a robot cleaner, could it be an air pump, that creates a "cushion" of air to expel the water through the nozzles ? where does it draw air from it doesn't seem to have any holes ?
My omron monitor display s one letter is missing.what l can do?
Could be a bad connection on the ribbon cable connecting the screen, but they are attached using a hot bar method which are very hard to repair
Почему сзади Bacic? Китай?
Good,solve the prolem & i desire to like yr technic,
where i can buy a motor supplying air in the cuff ?. coz my bp monitor doesnt inflate
thanks for your answer
Vincent Benitez it will cost u more to fix it ! it doesnt worth it at all. preety sure u cand just buy one..there are not so expensive 20-30 €at most 😉
He spent an odd amount of time expressing wonder at the various things he doesn't know and can't figure out.
I know lol
As appropriate
He could figure it out, he's obviously not retarded. It does seem a little weird that he's kinda treating it like he can't know things and its magic. Odd video. He didn't even fix the thing!
Thanks for the video even though it was posted some time ago. My OMRON BP762 monitor sudden stopped holding pressure. A cursory check showed the cuff was o.k. so the problem seems to be coming from the inside. I was about to take the thing apart in case it could be fixed. Your video however shows that this might be futile exercise. It's a shame since the unit is still in pristine condition.
I think the second valve is safety valve.
it is, I realised this after filming
Help me.i have 711 .error code er 81.how to fix it
Hi, sorry i cant help with this one, google is your friend here
my brother to can explain in audio spanish, to comunity spanish please
1a!
Buenas tardes, te comento que tengo un Omron HEM-431CINT, cuando trato de encenderlo el voltaje cae a cero, no consigo información, como rastrear el cortocircuito, es decir su diagrama eléctrico, pagina web donde buscar o en su defecto si me puedes orientar para corregir la falla, gracias. Saludos desde Maturin - Venezuela.
Hola amigo a mí me pasa lo mismo yo tengo un hem 631int da error y queda en cero has encontrado alguna solución
Hi, can you translate it into Spanish? ... Thank you.
i wont omrom bp spart airflo aand sarkit
afety valve i wont omron bp
You know nothing about it