Nobody else seems to remove the knuckle to do this job. The arm can be separated from the ball joint and wiggled out of the way and back in fairly easily with everything else still in place. Tighten the rear control arm bolt using a long extension with the car on the ground so the bushing is in a neutral position at normal ride height.
Yeah it’s way too many steps. He has new pads and rotors so they come out easy. Try that with old rotors, and you’ll run into unnecessary surprises like a seized rotor to the hub. Also like he mentioned, you can also risk damaging the CV boots, especially if they’re old.
He took it out to replace lower control arm ball joint which is pressed to the spindle. Stupid design. That ball joint would be better put on the lower control arm to avoid all this removal
I watched this video yesterday, and today, i successfully replaced my right side control arm on a '06 crv. However, i only removed 2 bolts and two nuts. Im not a mechanic, which is why i looked for a video like this.
There's No need to remove the brake caliper or the Shock bolt's, if you do Then your going to have to have it realigned.... Remove sway fitting first Ball joint fitting 2nd Then the other 2 Large bolts on the Control arm 3rd and 4 th...
Did the same on my 2001 Honda CRV. Slightly different part but same exercise. I can’t over emphasise the need to tie back the cv shaft avoiding it sliding out of the the drive shaft coupling. I ended up having to remove the cv shaft and reassemble the drive shaft joint. A lot of extra work!
Removing the rotor/hub assembly definatley makes this job easier, while it may not be required for this honda, for most front wheel drive vehicles you will not remove the lower ball joint easily as the axle is over the nut and the axle must be removed to get the ball joint nut off. Plus who wants to work around a spindle asswmbly dangling in the way....
No he's not, I've replaced dozens of these control arms on both CR-V's and Elements. There is absolutely no need to remove the rotor, caliper, axle locknut and spindle from the strut assembly, he'd never survive working in a flat rate shop...
❤Turn to Jesus people, he died for your sins. Repent of what the New testament describes as sin. Believe the gospel get baptized and obey the teachings of Jesus. The gospel and the teachings of Jesus are documented in Matthew Mark Luke and John. Jesus is the only way to be saved, if you have faith in Jesus through your faith you will live by his teachings. God bless 🙏
√ Watch the Video
√ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts
√ Do it Yourself
√ Save Money
I'm always working on my son's 2006 CRV. Your videos are A#1! Very professional. Thank you!
yeah man you just made this whole process complicated you could've removed the control arm without removing anything else
Nobody else seems to remove the knuckle to do this job. The arm can be separated from the ball joint and wiggled out of the way and back in fairly easily with everything else still in place. Tighten the rear control arm bolt using a long extension with the car on the ground so the bushing is in a neutral position at normal ride height.
Yeah it’s way too many steps. He has new pads and rotors so they come out easy. Try that with old rotors, and you’ll run into unnecessary surprises like a seized rotor to the hub. Also like he mentioned, you can also risk damaging the CV boots, especially if they’re old.
He took it out to replace lower control arm ball joint which is pressed to the spindle. Stupid design. That ball joint would be better put on the lower control arm to avoid all this removal
I watched this video yesterday, and today, i successfully replaced my right side control arm on a '06 crv. However, i only removed 2 bolts and two nuts. Im not a mechanic, which is why i looked for a video like this.
There's No need to remove the brake caliper or the Shock bolt's, if you do Then your going to have to have it realigned....
Remove sway fitting first
Ball joint fitting 2nd
Then the other 2 Large bolts on the Control arm 3rd and 4 th...
Did the same on my 2001 Honda CRV. Slightly different part but same exercise. I can’t over emphasise the need to tie back the cv shaft avoiding it sliding out of the the drive shaft coupling. I ended up having to remove the cv shaft and reassemble the drive shaft joint. A lot of extra work!
U forgot to remove the windshield and rear seats too…..
Yups as well water your neighbor's lawn and clean their bathrooms as well...
@@kalanikaau1 😆
The man who knows how explain stuff!!!!!!Big thanks to this man he’s gang!
Wow way to make a simple job overcomplicated!
Remove wheel
Remove bolt on lower ball joint
Remove roll bar links
Remove the 2 remaining screws
Done
This guy is good thank you sir 😊
Do you happen to have a video for a 2010 Acura MDX valve cover and tube seals?
Love your videos but can you do a starter replacement for 02 crv
What size pickle fork did you use?
Very good instructional video 👍🏼
Quick question the bolt for the lower rear bushing won't tighten do you have any ideas
Can you confirm that 36mm for axle nut and not 32mm. All the replacement nuts I see are listed as 32mm.
Removing the rotor/hub assembly definatley makes this job easier, while it may not be required for this honda, for most front wheel drive vehicles you will not remove the lower ball joint easily as the axle is over the nut and the axle must be removed to get the ball joint nut off. Plus who wants to work around a spindle asswmbly dangling in the way....
Very good videos !!!👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏
+JOSÉ Thanks for watching our video! 1aau.to/m/Shop-TRQ
so pro bro.
Thanks a lot sir.
This guy is good 👍
No he's not, I've replaced dozens of these control arms on both CR-V's and Elements. There is absolutely no need to remove the rotor, caliper, axle locknut and spindle from the strut assembly, he'd never survive working in a flat rate shop...
Show repair on control arm crv recall
Why replace it? What are the symptoms of a bad control arm?
Exelente video~~~~~~~
Exelente video
Repair back control arm recall on Honda crv
❤Turn to Jesus people, he died for your sins. Repent of what the New testament describes as sin. Believe the gospel get baptized and obey the teachings of Jesus. The gospel and the teachings of Jesus are documented in Matthew Mark Luke and John. Jesus is the only way to be saved, if you have faith in Jesus through your faith you will live by his teachings. God bless 🙏
Too much extra work for a simple job!!!