Installation went smoothly and easily with your guidance. Thank you for your instructions. FYI: I purchased my kit through Amazon and was able to get a kit specifically for the 331K. I have the 331K4 and it fit perfectly. Thank you again Harry.
thank you for a splendid video. Gunsmithing screwdrivers are the best tools to work with, especially on stubborn screws. The tips are configured so that there is NO TAPER where the tip enters the slot. check them out.
I had never seen one of these rollers installed, thanks for sharing. Now, you had trouble adjusting the height of the presser foot because you didn't follow the normal procedures. To ensure the presser foot is properly adjusted you must keep at least a 1mm distance between the presser foot raising cam and the contact point before you tighten the presser foot bar clamp, I just stick a thin screwdriver between the two contact surfaces and it works like a charm.
I put this roller foot on my singer 241-12 and had to do modifications to the roller foot itself to clear the needle bar. But I got it working good. The new feed dog and plate were horrible so I ended up using the original feed dog which was close to the new one
So you're going to loop the loop on a sewing machine - wearing a flying jacket I hope ! This film ( I NEARLY put "video" - oh dear ! ) whilst demonstrating a roller wheel, also has been a "fantastically" useful demonstration of the mechanics of the business end of the machine. ( Do you remember back in the 1960s when there were decent programmes on television, there was an old time music hall on BBC, with a gentleman Leonard Sachs dressed up as a Victorian with a starched mustache who tapped with a gavel and introduced comedy acts - he always used big words such as "fantastically", and whenever he did so, the audience gasped ? If HE can say "fantastically, so can we ! ) Anyway, your latest descriptive film going to be useful when I finally get around to maintaining my 1896 flying shuttle machine ! Yes there was a manual for it on the ISMACS website - thank you SO much for pointing me in the direction of that information source ! Beautiful, geometrically correct stitches that you are already getting on your machine in your film. Lovely to see it, and to hear the equally perfect click clack of the mechanism. A joy to see and to hear ! Thank you for all of this ! Time to enjoy a mug of tea to celebrate - cheers !
Hello Phil...what a fantastically good and detailed response...just like the 'Good Old Days'...now where is my own, my very own hammer, the one and only...err gavel !
I found this video to be very informative. I am trying to do a similar conversion on my Singer 66 for some leather craft projects. Would you be able to post a link to locate the parts featured in this video? (feed dog, plates, and roller presser foot) Thanks!
Hello Harry, First off I wish to thank you for taking the time to produce tutorial videos. I have been searching for the last hour for this kit. I wonder if you would be so kind as to post the link? Thanks! Lynn
@@harryrogers Thanks, Harry. I did find a vendor on ebay that sells the kit and asked them if the kit will fit my machine. This is the reply (I had a good laugh): "Hello, We can not offer that anything will ever be 100% effective or 100% to any specific standards for obvious legal issues that arise with guarantees and verbiage along those lines."
Quick question on the hand pully conversion! You where turning it counter clockwise to fallow the sewing machine to sow, what happens if you turn it clock wise? Will it act like a reverse stich? Great video bye the way! 👌👍📹
Thanks for the video.....I have no real experience with a drop feed machine.... But does this machine not give you the ability to do tight curves without the roller foot?
Thanks very much for all your videos. I have a question about my 31k I recently bought. I'm wondering about the type of needle I need (regular or industrial ? ), I'm sewing leather, and I'd like to be sure to use the proper accessories with it ! Another question, I'm sewing (trying to) oiled leather, not very thick but bolky and stiff, with a 120 leather needle (regular, not industrial), it goes fine when I sew one layer of this leather with another type of leather on it, but 2 layers of oiled leather and the needle is barely impossible to move, even by hand, and it sounds like something is touching the needle underneath (the hook probably, not happening with other types of leather...). Help !?
Hi Claire...sorry I no longer have this machine, but you need to Google the correct needle, as I recall it was an industrial type. It you go for an raw type you will get a nice stitch for leather. It sounds like you need a thicker needle for the thick leather as it might be flexing.
@@harryrogers thanks very much for taking the time to answer all my questions :) I'll try a thicker needle. Not easy to find informations about the adapted accessories for this machine. I'll keep searching on english websites as I can't find anything relevant in French ^^
I have a older Pfaff 195 post bed walking foot . Would consider having the roller ,mainly to stitch zippers on boots and bag straps. Do you think its wise to do the switch?
Thank you. i was recommened to try one of theses roller foots for my brother industiral machine for doing my boat seats and vinly /leather work how you finding it ? you notice a big difference in using one?
Hi Harry, thanks for taking the time to Come back to my other anvil question. Ive just purchased a Singer 331k4 on ebay it works (just about) but is a bit of a cosmetic mess so the plan is to completely restore and doing the hand crank conversion. Assuming that I did the roller foot conversion, used a sensible needle and strong bonded nylon thread what sort of thickness of veg tan leather do you think Ill be able to sew through? Thanks Steve
Do you always use that machine with the hand-crank only? Btw, you used a term I am not familiar with: pique? I tried searching it and found nothing. Is it just a word for embroidery?
I think the Singer 66 is low shank unlike this Singer 331k and I am not aware of a roller like this that you can get for the Singer 66, but you can get a standard foot with little wheels. Maybe someone here cab advise further.
Good job! But that is so fiddly you will probably want to get another Singer so you can have one with the normal system and one with the roller foot - - - then you will have to increase your work area of course . . .
Why you did not mark where you were going to make adjustments is beyond me. Also why didn't you just file the dog plate instead? You could have saved much time and no need to move anything out of timing. Just my opinion and it does not mean much. Thank you for the video.
Good idea to file the dog plate...it was quick and easy to grind off the side of the dog, but I think your suggestion of filing the plate is better. I did not mark as I know what works...what really caught me out was the different shape of the hook recess...I assumed it would be the same as a genuine Singer part, but the arm indent was very slightly different. Thanks for your comments. Rgds Harry
Ese pie de rodaja miente falla no es esacto como el que es fijo de la máquina Pero hay que cambiar El poste Bueno y a parte que se mira feo poco estetico
Education is a wonderful thing, I learn something new every day.
Installation went smoothly and easily with your guidance. Thank you for your instructions. FYI: I purchased my kit through Amazon and was able to get a kit specifically for the 331K. I have the 331K4 and it fit perfectly. Thank you again Harry.
very interesting mr Rogers, i am going to try it out on my old singer, this has given me inspiration to boldly go to the unknown.
Due diligent work there! It was amazing to see your careful sewing machine adjustments did not affect *the* *timing* of your machine!
Excellent video. Prior to the video, I was unaware of the roller/wheel function.
very interesting, well explained, good visuals, nice job done well
Harry I've just started watching your videos and already I know they will help me immensely. Easily understood and thorough., Thank you!
Thanks Mike.
Very nice job, Mr Rogers I wait to see those high top cowboy boots.
Thank you very much! I looked your videos searching a solution for another thing and you gave me the solution!!! Magical ;D
You are a wonderful teacher!
thank you for a splendid video. Gunsmithing screwdrivers are the best tools to work with, especially on stubborn screws. The tips are configured so that there is NO TAPER where the tip enters the slot. check them out.
Great Video, Harry! You now have a new subscriber!
Thanks Bernie.
I had never seen one of these rollers installed, thanks for sharing. Now, you had trouble adjusting the height of the presser foot because you didn't follow the normal procedures. To ensure the presser foot is properly adjusted you must keep at least a 1mm distance between the presser foot raising cam and the contact point before you tighten the presser foot bar clamp, I just stick a thin screwdriver between the two contact surfaces and it works like a charm.
good visuals, nice job. looks like you have it fine tuned ready to sew
I put this roller foot on my singer 241-12 and had to do modifications to the roller foot itself to clear the needle bar. But I got it working good. The new feed dog and plate were horrible so I ended up using the original feed dog which was close to the new one
Happy I found this video I couldn’t get the wheel to fit
FANTASTIC, EXCELLENT VIDEO!!!! But this Roller foot is for a high shank sewing machine, where I can get this for a low shank sewing machine?
Wonderful, well explained. Thanks Harry
Good job sir. Thanks for enlightenment.
Thanks for your videos btw. Very didactic and educational. Excellent job.
Good job
So you're going to loop the loop on a sewing machine - wearing a flying jacket I hope ! This film ( I NEARLY put "video" - oh dear ! ) whilst demonstrating a roller wheel, also has been a "fantastically" useful demonstration of the mechanics of the business end of the machine. ( Do you remember back in the 1960s when there were decent programmes on television, there was an old time music hall on BBC, with a gentleman Leonard Sachs dressed up as a Victorian with a starched mustache who tapped with a gavel and introduced comedy acts - he always used big words such as "fantastically", and whenever he did so, the audience gasped ? If HE can say "fantastically, so can we ! ) Anyway, your latest descriptive film going to be useful when I finally get around to maintaining my 1896 flying shuttle machine ! Yes there was a manual for it on the ISMACS website - thank you SO much for pointing me in the direction of that information source ! Beautiful, geometrically correct stitches that you are already getting on your machine in your film. Lovely to see it, and to hear the equally perfect click clack of the mechanism. A joy to see and to hear ! Thank you for all of this ! Time to enjoy a mug of tea to celebrate - cheers !
Hello Phil...what a fantastically good and detailed response...just like the 'Good Old Days'...now where is my own, my very own hammer, the one and only...err gavel !
Where am I able to buy a conversion kit. I have a 201K (201p in Australia)
When it didn't go down right at 8:16... I was like, Oh lord, how much more must this man endure to get this roller foot rolling? 😭😭
Wonder how that works in reverse stich.
That's fabulous!
Hi Harry, great video as usual. Do you mind me asking where you sourced your conversion kit from please? Thanks once again.
Clever gentleman!
I found this video to be very informative. I am trying to do a similar conversion on my Singer 66 for some leather craft projects. Would you be able to post a link to locate the parts featured in this video? (feed dog, plates, and roller presser foot) Thanks!
Hi the Singer 66 does not have a high rise industrial foot, so I think you might have to be inventive....but I might be wrong. I got parts off Ebay.
Hello Harry,
First off I wish to thank you for taking the time to produce tutorial videos.
I have been searching for the last hour for this kit. I wonder if you would be so kind as to post the link? Thanks!
Lynn
Hi I have popped details in the comments
Thank you Harry.
I have a Singer 15-91 so, not if the kit will fit.
@@kboleather I think it needs to be a high shank foot machine...I am sorry I don't know if yours is suitable...perhaps someone here will know.
@@harryrogers
Thanks, Harry.
I did find a vendor on ebay that sells the kit and asked them if the kit will fit my machine. This is the reply (I had a good laugh):
"Hello,
We can not offer that anything will ever be 100% effective or 100% to any specific standards for obvious legal issues that arise with guarantees and verbiage along those lines."
Quick question on the hand pully conversion! You where turning it counter clockwise to fallow the sewing machine to sow, what happens if you turn it clock wise? Will it act like a reverse stich? Great video bye the way! 👌👍📹
Hi that would mess up most machines.
Thanks for the video.....I have no real experience with a drop feed machine.... But does this machine not give you the ability to do tight curves without the roller foot?
Yes that's right...though the roller foot let's you do really tight curves.
Thanks very much for all your videos. I have a question about my 31k I recently bought.
I'm wondering about the type of needle I need (regular or industrial ? ), I'm sewing leather, and I'd like to be sure to use the proper accessories with it !
Another question, I'm sewing (trying to) oiled leather, not very thick but bolky and stiff, with a 120 leather needle (regular, not industrial), it goes fine when I sew one layer of this leather with another type of leather on it, but 2 layers of oiled leather and the needle is barely impossible to move, even by hand, and it sounds like something is touching the needle underneath (the hook probably, not happening with other types of leather...). Help !?
Hi Claire...sorry I no longer have this machine, but you need to Google the correct needle, as I recall it was an industrial type. It you go for an raw type you will get a nice stitch for leather. It sounds like you need a thicker needle for the thick leather as it might be flexing.
@@harryrogers thanks very much for taking the time to answer all my questions :) I'll try a thicker needle. Not easy to find informations about the adapted accessories for this machine. I'll keep searching on english websites as I can't find anything relevant in French ^^
@@littlelila I got needles from College Sewing...maybe look for the user manual on their website or try ISMACS website as well.
@@harryrogers Thank you :) !!!!
Great demo! Wonder if the foot comes in low shank? I have an old Kenmore sewing machine about 15 years old.
Do Pfaff do one???? Not sure.
Hi Harry, I've been following your videos. I am wondering if you have a link to buy the plate and feed dog by any chance handy? Thanks a million.
Hello,
Would you be so kind as to give us the name of the company that supplied the conversion, thank you
Ebay...description
4 PIECE SEWING ROLLER FOOT SET FIT for JUKI CONSEW 12264 12267
Seller
Kunpengsewingpartsforuk
Harry Rogers ordering thank you
Bravo
Hola de cuántas pulgadas son los 2 pulle
Hi Harry, Where did you buy the conversion kit? Can you do this to other old singers?
Hello, do you know if a roller foot is available for a singer 95k10 or something that would fit?
I fitted mine to a high shank machine, I am sorry I do not know if your machine is high or low shank.
good on you Harry,,,what size needle and thread did you use?
Thanks - mostly a MN60 or a MN40 thread with 90 or 110 or 120 RTW chisel type needles depending on the leather and effect I am trying to get.
@@harryrogers thanks Harry,,much appreciated,,
I have a older Pfaff 195 post bed walking foot . Would consider having the roller ,mainly to stitch zippers on boots and bag straps. Do you think its wise to do the switch?
I like the roller on my post bed for flat sewing work...stress flat sewing.
@@harryrogers is the allowable thickness of the leather being stitch changes after switching over to the roller ?
@@cobblerq1 Not if you can raise the shank it is attached to...not that I am a sewing machine mechanic...so you may want to take professional advice.
Thank you. i was recommened to try one of theses roller foots for my brother industiral machine for doing my boat seats and vinly /leather work how you finding it ? you notice a big difference in using one?
Hi its a good feed with very good needle visibility
How to determine what size to be used?
Small for tight curves and low seams, big for big curves and higher seams.
❤❤❤
Hi Harry, thanks for taking the time to
Come back to my other anvil question. Ive just purchased a Singer 331k4 on ebay it works (just about) but is a bit of a cosmetic mess so the plan is to completely restore and doing the hand crank conversion. Assuming that I did the roller foot conversion, used a sensible needle and strong bonded nylon thread what sort of thickness of veg tan leather do you think Ill be able to sew through? Thanks Steve
I am not certain....it should manage two layers of 1.5mm leather no problem...I have not tried thicker stuff.
Harry Rogers ok thanks Harry!
Links for the roller and where to buy?
Try Ebay
Hello. Where can I purchase the rolling foot kit, please?
Hi I got mine from eBay a few years ago.
For this machine I think it's a high shank foot.
Do you always use that machine with the hand-crank only? Btw, you used a term I am not familiar with: pique? I tried searching it and found nothing. Is it just a word for embroidery?
_Appliqué_ is the word he used. It is a type of embroidery sewing.
Also whats wrong with philosophy?
Can you give me more information about singer 31k
ISMACS website probably has a manual
Can this also be added to a singer 29k?
Hi Sol...I don't think it can.
Wow
Hi! I have a question, Where can I buy a roller foot? I have Singer 66K and would like to install roller foot
I think the Singer 66 is low shank unlike this Singer 331k and I am not aware of a roller like this that you can get for the Singer 66, but you can get a standard foot with little wheels. Maybe someone here cab advise further.
Bravo 🌹
Hi where did you get roller foot please.
Hi EBay China, it's s generic part you can get in a lot of places.
thanks
Could you have filed the top plate instead of grinding the feed dog?
Yes that will work as well.
COOL~!!
After all that effort, one can see why some people keep machines dedicated to specific functions.
Wonderful experience; machine and technician Rogers. If I'd one.....
Ezekiel
October 8 2024
where i can buy a roller foot?
Sewing shop or EBay.
👍
OK same idea, cut the feed dog to fit~
Good job! But that is so fiddly you will probably want to get another Singer so you can have one with the normal system and one with the roller foot - - - then you will have to increase your work area of course . . .
Thanks David....yes I don't think I would want this as my only machine, unless all I did was patterns etc on boots uppers or applique on bags etc.
Why you did not mark where you were going to make adjustments is beyond me. Also why didn't you just file the dog plate instead? You could have saved much time and no need to move anything out of timing. Just my opinion and it does not mean much. Thank you for the video.
Good idea to file the dog plate...it was quick and easy to grind off the side of the dog, but I think your suggestion of filing the plate is better. I did not mark as I know what works...what really caught me out was the different shape of the hook recess...I assumed it would be the same as a genuine Singer part, but the arm indent was very slightly different. Thanks for your comments. Rgds Harry
Ese pie de rodaja miente falla no es esacto como el que es fijo de la máquina
Pero hay que cambiar
El poste
Bueno y a parte que se mira feo poco estetico