BMW Motorcycle ABS-II Reset
Вставка
- Опубліковано 17 кві 2013
- Store: www.amazon.com/shop/illinoisb...
Patreon: / kirkjohnson
Paypal donations: www.paypal.me/14wntr
Shop Merch: teespring.com/stores/kirks-mo...
K1200LT Shop Poster: www.ebay.com/itm/132241883054
Contact: www.kirksmotorrad.com
A video created by Kirk's Motorrad Shop. Please work at your own risk. We are not responsible for any damage you do. - Авто та транспорт
Thank you for explaining the process, I’ve just purchased a R1150GS with that ABS II and the light sequences are driving me nuts! I will swap the battery soon (the bike has been standing unused for a while) and follow the sequence shown.
(2) "On my 2000 K1200LT the brown/blue wire was the correct wire to use on the diagnostic plug. You have to remove the large 25 pin connector from the ABS unit, remove one tie wrap and three phillips head screws on the connector (two are under the rubber that was held on by the tie wrap). After you have done this and exposed the wires and female connector plug you can see where pin 21 is numbered on the connector. (above)
I just wanted to add for K1200LT... The K1200, R1200C and R1100S use the same ABS2 units as the 1150GS, but there is no ABS switch to use for the reset procedure. If you can access pin #21 on the ABS unit, you can ground it to achieve the same effect as having the ABS button. Pin #21 will be on the large connector to the ABS unit. I've gotten confirmation from K12 and R11S owners that they were successful. Here's one description: (above)
Awesome! Just worked for me! Let’s see after a test ride tomorrow. Thanks!
I first thought that one of the ABS sensors were defect from my 850RT but after replacing the battery and perform the reset as described in the video the ABS was up and running again !!!!!! THANKS !!!!!
Thank you, very much, from Spain, muy agradecido, me ha servido para mi K1100LT
(3) I used a 14 gage wire with an aligator clip on one end with about 1/16" of copper exposed and plugged it in the pin 21 slot and reinstalled the connector without the connector housing. I then made sure it felt like I had good contact on pin 21. I then used a straight pin and another 14 gage piece of wire with an aligator clip to pin into the brown and blue wire on the maintenance connector and then aligator clipped this to the negative terminal on the battery. (above)
From Spain. Thank you very much.
Thank you very much.
Muchísimas gracias.
Saludos from Spain.
ho giusto questo problema e vedendo il tuo video molto ben fatto ho risolto.grazie e complimenti.
Thanks for the video! Works with the BMW R850 RT 1996 as wel.
Thanks man, worked with my 1994 R1100GS, had issues at first but turned out he ABS button itself was also faulty.
Great demo thanks. Cant find the cap on my bike. It as the same situation with the abs.
Thanks a lot from Germany.
Thanks, very interesting !!!
hi, thanks foe sharing so good video, i ve problem with my BMW K1200S servo ABS module not working, no power in the brakes. very expensive not get new fitted in, any other idea/help ?? regards.
(4) I then turned the key to on and then touched the alligator clip from pin 21 to the negative terminal on the battery (8 seconds is fine but mine immediately reset). The ABS lights went from alternate flashing to normal flashing simultaneously. (sorry I had to brake this in to 4 parts. But I thought some buy with a K1200LT would like to know so he dont have to take it to the dealer.
WHAT IS THE ABS RESET PROCEDURE FOR A 2002 BMW K1200 LT?? (I have alternate red flashing lights on my dash)
Hello, please can you help?? I have watched your videos on the ABS-II. But, my 1999 K1200RS is different! It has a round connector and no ABS button.
Reason that the lights are flashed alternating is that I turned on the engine after a clutch change without the drive shaft and final drive connected (sensors disconnect) and the battery was low too.
Please help. Thank you.
Great demo thanks. Could you please tell me how to replace riders display unit on a 1997 BMW R1100RT. My bike's display is not properly functioning. It doesn't show temp and gear. I saw a unit being sold on Ebay. Thought to buy it but want to know how to install it first. I am a new rider of BMW. Thanks for the help.
Thanks for the video, I have an R1100S year 1999, the ABS is sometimes working and sometimes not. I don t have an ABS button as on yourRT, so could you help me reseting the ABS so it can work again? Thanks.
Thank you. thank you, thank you!!!
Seems like a quick enough fix- However, I took my K1200S to an agent who hooked it up to a diagnostic computer- which in turn displayed an error of "Modulator failure".. I must confess, I had my braking system flushed and I suspect some grit might have entered the modulator which is now flashing continuously. Any ideas from your experience if my suspicion could be warranted?
Just did this and still had the issue- guess I'm just due for a new battery. Thanks all the same!
Does explain clearly just how to reset the ABS Module. See if I actually go and buy this 2001 later today. Its a train wreck, so a whole lot of iffy involved. Thanks.
Hi I have a 2011 rt1200 ex police motorcycle but it has break failure notice on it I have checked the sistem and road tested the bike but everything seams to be working fine can you advise
Nearly every time I ride, my 96 R1100RT, I get a ABS fault. I reset it by cycling the key on and off, and doing a rolling start it resets. Might take a few tries. All good until I turn off the key. Then its repeat the procedure. Very annoying.
I assume I am having some sort of sensor error. I am considering pulling out the mechanical sensors and cleaning and inspecting them. But first I will try this. Nothing to lose.
My bike doesnt make all those sounds when doing this procedure, is there something wrong? ;) Thanks for the video.
Super, thks for this information :-)
Did you install speakers for your r1100rt?
can you please tell me if I can do this on my 1998 K 1200 RS
+Constantine T You should be able to.
I have a k1100rs from the year 95 with the abs 2 I did the thing in the video but it still doesn't work... when I ride the bike a bit I notice that the abs system on the rear wheel makes a noise but the one on the front doesn't it does....what could it be?????
It sounds like the ABS is shot. Contact Modulemasters for a rebuild
Falto ver de nuevo el cuadro de luces. Sabéis alguno donde está el relé de bomba gasolina?
Gracias
Creo que está debajo del tanque de gasolina dentro de un bloque de fusibles
@@kirksmotorrad debajo del asiento hay unos cuantos, mi problema es de una BMW 1100RT que lleva más de cuatro años parada. Y no le llega gasolina.
Cambiar la bomba de combustible. Es muy probable que sea malo