rubesh baskaran I’m sure he does. Otherwise why would he ask us questions in the comment section and why not just disable comments if he doesn’t read them.
Take 2 nuts, tighten them together on the stud, then you should be able to take the stud out. I would suggest reversing the process when putting them back in. Finger tight with thread locker isn't going to work. And I bet you won't read this comment or like it.
*that satisfaction when it started!!!* Im enjoying every second of this build! Its amaizing how far this channel has come from nothing, been here since the early days and im willing to stick around for a loong time!
I installed a gtx2867r turbo onto my focus st it was tough i didnt replace anything related to my fuel or exhaust manifold... but i had to reuse my boost controller run the oil and coolant lines it was tough taking it out for a coolant leak and then an oil leak but it got on i was under my car for 3 whole days waking up going under then going to sleep and getting started the next day its awsome to learn and have a sense of accomplishment once its done worth everything installing a bigger turbo its a new car hope you have a similar experience once your build is done.
You shouldn't use teflon tape for oil fittings. If it breaks off, it could clog. Myself and a good amount of other Miataturbo people have good experience with Permatex thread sealant. It doesn't break apart like teflon tape would.
song was pretty chill, sounds like some of the hats were a little off-beat, bit of a clean up in the bass, the saw synth pad could use a bit more space. but definitely a good chill song for vlogs
It's important to prime the turbo with oil first before actually starting the car. You can pull fuel pump fuse and turn key for about 10sec a few times.
try to always pull the fuel pump fuel out and crank the car for a while when you have a new turbo guys, thats just to make sure some oil is their when the car starts spinning it, also ur leak might be because those studs are on wrong... not sure but it just looked like it so u might have them flipped i guess... i hope u read this
Lol this is kinda funny because I had to drive to Summit Racing today. I hate they are located so far south of Arlington. Also hate the lines too. Guaranteed wait time.
You're welcome! Although I should be thanking you for this videos and God for creating you and Victoria so I can forget about the bad things in life for a while and thank HIM for people and content like you(rs).
YOU PUT THE STUDS IN BACKWARDS BROTHER!!!!
TNC Media he said he doesn't read comments so RIP
Next video: I blew up the evo...😂 cuz I didn't listen to my boys😅👌
I seen this comment to many times smh 🤦♀️
BROTHER DON'T DO IT BORTHER
Thats what I've been saying the last 3 video's, so cringe
Boi your studs are in backwards for the turbo listen to us evan
Brink Zenco when are you all going to realize that he doesnt read commments? Hit him up on twitter...
He doesn’t read comments cause he can’t take criticism 😭
Tweet him
rubesh baskaran I’m sure he does. Otherwise why would he ask us questions in the comment section and why not just disable comments if he doesn’t read them.
studs on turbo are backwards and don't use teflon on fittings. not trying to be mean just don't want you to mess up all that money. 😁
chapstick
garrett2jz Lmaooo i commented the same exact thing and scrolled down and saw this
BLISTEX SEND THIS MAN A CARE PACKAGE
when i wake up i always have to poop immediately wbu
Evan Shanks well today I have to watch daddy start the Evo
Legitness
Evan Shanks I have to pee
Evan Shanks i need to pee every morning
nope, after some coffee and food... but then yes
Teflon tape doesn’t hold up to fuel. AN fittings seal their selves together the the slope angle of the fitting. Come on now Evan
taperrrr
10:28 it’s because they are in backwards my dude
Next time prime the turbo young grasshopper.
Why you no prime the turbo😩
Evan listen to everyone your studs are in BACKWARDS
Dont think hes really a car guy just in for the youtube checks.....
Don't put teflon tape on AN fittings!!!
I ended up not having to anyways :)
You dah man!
Dad, some of your bolts are backwards. Furthermore, do not use teflon tape on a fuel line because it won’t hold.
When you selling it?
Ayy nice job my guy this build is really clean. This whole thing is a learning process, keep it up!
you NEED some damn chapstick boyyy
Lookin like Thanos Shanks with that lip action.
Take 2 nuts, tighten them together on the stud, then you should be able to take the stud out. I would suggest reversing the process when putting them back in. Finger tight with thread locker isn't going to work. And I bet you won't read this comment or like it.
No Lag Productions I've told him the same for the last three videos he's won't listen till something breaks
Dolly DeHart if he would read the comments, it takes the guess work out. I've been working on cars for longer than he's had a license.
*that satisfaction when it started!!!* Im enjoying every second of this build! Its amaizing how far this channel has come from nothing, been here since the early days and im willing to stick around for a loong time!
Evan, I thoroughly enjoy your videos. Normally I skip through most UA-camr's videos, but I watch yours entirely. XO
I was about to schlump, but daddy posted so ig I can't lmao
Timing is on point✌🏻
Clutch is the cutest doggo ever
What a blessing to be able to build race cars and have an amazing girl by your side to support you. Enjoy it man.
I installed a gtx2867r turbo onto my focus st it was tough i didnt replace anything related to my fuel or exhaust manifold... but i had to reuse my boost controller run the oil and coolant lines it was tough taking it out for a coolant leak and then an oil leak but it got on i was under my car for 3 whole days waking up going under then going to sleep and getting started the next day its awsome to learn and have a sense of accomplishment once its done worth everything installing a bigger turbo its a new car hope you have a similar experience once your build is done.
beat or song it’s pretty dope 🤔
Raffy Things yeah sounds like man's put a fart on da beat
That music is so much better than the normal rubbish, your friend should do more. Do you not need PTFE tape around those oil fittings?
You shouldn't use teflon tape for oil fittings. If it breaks off, it could clog. Myself and a good amount of other Miataturbo people have good experience with Permatex thread sealant. It doesn't break apart like teflon tape would.
He got to put this on YT, but don't forget, we are not awesome, YOU are awesome because without you, there won't be us
You're the man. That Evo is woke like Evan is.
song was pretty chill, sounds like some of the hats were a little off-beat, bit of a clean up in the bass, the saw synth pad could use a bit more space. but definitely a good chill song for vlogs
Dude’s got kyle in his spirit
that's why you get a turbo kit intead of several parts by yourself
next stop, 272 cams! Open that powerband!
It's important to prime the turbo with oil first before actually starting the car. You can pull fuel pump fuse and turn key for about 10sec a few times.
Evan bro, MVP here, get the tap and die set out man and retap the hole to make the stud go in more man
That music is pretty chill and dope!! Perfect for edits!!!
Remove the manifold and try to lock two nut together on the stud. After that you should be able to use the top one to screw the stud in.
Lucky you didnt light that new turbo on fire boyyyyy,
Open Downpipe = Flames
Fuel + Open Downpipe = FIRE
The "big hole" in the center section of the turbo is the oil return.
try to always pull the fuel pump fuel out and crank the car for a while when you have a new turbo guys, thats just to make sure some oil is their when the car starts spinning it, also ur leak might be because those studs are on wrong... not sure but it just looked like it so u might have them flipped i guess... i hope u read this
Let’s get this MANS some CHAPSTICK
Finally some original music!
So glad you finally got the car started dude !! Been watching your videos for the longest now😂 and they’re great🙌🏽
Sounds like a westcoast banger CUZ
The summit in Arlington always has everything I need
I bet no one's ever told you this, but...CHAPSTICK. Enjoyed the video man.
Clutch is soo big compared to last time we properly saw him in videos
The music tracks were dope!
You could've done a very good title " nearly burned my engine while starting it " 😂😂😂
Way to go.. Good job.. Now if I could JUST get some time and drag my azz to the garage and rebuild my McLaren Turbo Grand Prix.. I'd be all set too..
5:45 buddy was excited lol
Thank you Kanye, very cool
Aye something to watch after exams🤠🤠
You could always ceramic coat the turbo manifold to keep the heat down in the engine bay.
Those tunes dope asffff
Love the music, has a midnight club 3 vibe to it
yes please have him put that on Soundcloud and throw a link in! would love to follow
THESE SONGS ARE LITTY
yo that song he made was cool I need to see the turbo on that Nissan grr
I’m so exited for it to be driving
He should use that starting montage as a channel introduction
anytime u r dealing with stainless use antisieze to help bolts from seizing. use wd40 to loosen up stick bolt
Hey nice videos. But FYI you needed to prime your new turbo. Also with that stud. Use to nuts to bolt it down or pull it out. 👍🏼
It's 1:30 am is Australia, but when dad uploads nothing else matters.
I was sooo bored, BUT, then i saw that my boy Evan posted a vid...so happy rn
It’s not that hard to keep watching a fun turbo built from a funny person fam
Hard work pays off bro
Hello, i have a lancer 2009, and i have problem with the RPM doesn’t go more than 4000,
If someone knows what is the problem let me know plz.
When will this finally be done? My guess is the big reveal video will by June 11th..
what is that piano sample at 0:25? it sounds so good, where the rest of it?
that fuel leak got me thinking, have you got a fire extinguisher Evan?
Evan is that guy who puts a turbo on an stuck engine
Just ordered a bunch of merch to Alaska!
Am I the only one who thinks clutch and Victoria kinda look alike??? Lol idk why but I always see that!
Star Wars battlefront all the way 👀
Evan don’t Teflon tape fuel line fittings. You’ll regret it if a piece brakes off... AN fittings DONT require any kind of sealant
She starts! 🙏🏼 my guy
Song is sick, best intro in video ever, sick
Take the exhaust housing off bro then you can scree the fittings on
11:26 you're welcome Evan! 😉😊
I need to know what breed your pupperino is
Hey you should really put Teflon tape on those oil fittings that thread in they will leake
Damn evan you need some chapstick bro
You don’t Teflon tape an fittings. There is a proper torque. Use crows feet and torque them. If it’s pipe thread then tape it.
Good music, great video. Excellent way to start the day
Not saying i didnt love the music but im saying that it and your video combined kinda reminded me a of a weird throw back of Pimp My Ride.
I don't comment too much but I watch every vid you put up but keep it up! I'm enjoying them!
Get a harness for the dog that conects to the seat belt lock. Much safwr
Beat dope asf🙏🚀🔥
Damn I live right around the corner from that smileys 😂
the music aint what id call chill
Hey Evan just to that guy... You can't use your stock valve cover 😂
10\10 music!!!
Damn this music is fire!
water my guy, we need you alive
I think the chick knows more about cars then the dude
Lol this is kinda funny because I had to drive to Summit Racing today. I hate they are located so far south of Arlington. Also hate the lines too. Guaranteed wait time.
You're welcome! Although I should be thanking you for this videos and God for creating you and Victoria so I can forget about the bad things in life for a while and thank HIM for people and content like you(rs).
Soon as I see your video man I quickly get my food ready and watch your content ❤️
This guys videos crack me up every single time, but not because he’s funny..
Evan you can’t use the stock valve cover