Smoke Effect Tumbler Tutorial
Вставка
- Опубліковано 7 вер 2024
- Smoke Effect Tumbler
Join me with my first attempt at the smoke effect tumbler!
Materials Used:
Tumbler: Ozark Trial 14 ounce Wine
You May also purchase tumblers here: makerflocrafts...?sca_ref=239348.FKXyRoUttw
My favorite Epoxy: www.p3hfsftrk....
Use my Code: MISSKISS to receive 10% off your order.
91% alcohol (for prepping)
Spray Paint: Aqua- Rust-o-leum
Candle
Candle holder/ plate for under candle
Lighter to light candle
Silverware(knife is easier to handle)
Measuring cups for epoxy
Wooden sticks for epoxy
Nitrile Gloves
Decal Used: etsy.me/2ROPTPp
Epoxy: www.alumilite.com?aff=75
Cup turner: www.amazon.com...
Respirator Mask: www.amazon.com...
UA-cam VIDEO LINKS
How to Epoxy a Tumbler:
• How to Epoxy a Tumbler
How to mix epoxy properly:
• How to mix epoxy corre...
Thank you all for the love and support!!!! 🥂
I found that incense work perfectly for this 😊 just light them and dont blow them out and you have slow and steady black smoke 👍
Your voice is very pleasant to listen to. I just purchased my first turner and you have given me some much needed confidence😂 New subscriber here 🥰 thank you so much
I have been reading about smoke tumblers and didn't have a clue.. but oh my gosh THAT IS AWESOME!!! I can just see a white tumbler with a peekaboo red name and the black smoke!! CAN'T WAIT TO DO IT!! Thank you, I learn so much from you every time I watch a video!
Wow! Fantastic!!! Thanks so much. I watched your alcohol ink video earlier and just made my first alcohol ink 32 oz tumbler! You teach very quick and well!!! Thanks again!
Thank you so much!!! It’s my pleasure!
Cool results. 👍🏻👍🏻 If you want an easy way to get your smoke you can pick up a cheap oil lamp. Just take off the chimney and extend the wick a little farther out than normal until you get the desired amount of smoke.
Thank you so much for the tip!!!
Ms. Kiss Kreations You’re welcome! It should make it easier because you can use both hands to manipulate the tumbler.
Have a great night.
That turned out beautifully thank you for sharing your link
Fun with science. I love this effect. Plan to try this very soon. Meantime, how is the smoke being made? The hottest part of a candle flame is the outermost part of the flame where the most oxygen is available to feed combustion. Gasses (i.e., the black smoke as well as invisible combustible gasses) move up thru the flame from the paraffin and are most completely burnt at the outer edge of the flame. The knife tip is simply interfering with the flow of the gas to the corona of the flame and preventing the gas from being burnt efficiently. Result; more soot or black smoke. It will be interesting to try different shapes of metal probes to interfere with the flame and find out what effects they will have. Perhaps a scratch awl placed directly thru the center of the flame would produce more soot or be more controllable. There is also the potential to get this effect with an oil burning lamp. Allowing a wick to extend too far generates a lot of black soot. This is exactly the sort of experimenting that makes these crafts so entertaining. Thanks for demonstrating this great effect.
Thank you for sharing. I am about to do this technique and wasn't sure if needed to seal after the smoke. You saved me a step!! Thanks!
Looks awesome!!! Been doing this technique for years,but with different mediums and outcomes... need to practice it on this medium..also a tip is..the cheaper the candle,the more smoke it will create..
Awesome!! Thank you for the tip!!
I found using a tiki torch makes much more smoke and faster. No utensils needed 😊
That's good to know ty :)
Great idea!!!
I was wondering about that! Our set up is in the garage and we have like 10 mini tikis for the holidays!
Thank you! Thank you! Thank you! I've been wanting to try this method but was nervous. Once again, you give such clear instructions that you give me the courage to try myself!!
thank you so much. your technique worked perfectly!
I really loved the way you applied the smoke technique! Thanks for this tutorial!
I was concerned the heat would travel through the knife and burn your hand. I think you did great for a first time. I really need to try this
That was pretty cool! Watching the smoke transfer to the tumbler and then the epoxy application was super satisfying to watch haha
It’s amazing the smoke did not rub off when you were applying the decal. How do you clean up the rim when you are finished.
Thanks for making this video. I feel like I want to try to make one . And I live that it is not super expensive to make!!
Am so happy that i can just apply the stickers and epoxy last. Yes money saver
Prepping a tumbler now to try this!
Thats so cool! I would like to do it on a glittered tumbler!
Looks amazing....You have given me the perfect solution to a problem I've had for a background ❤ x
Purple will be absolutely beautiful!!!!
I did this on a flask... I love it. Thank you for the tutorial
All your tutorials have been so helpful! Thank you for sharing! Another great tutorial!
Thank you so much!!
I love how it turned out! So excited to try this method.
Thank you!!
Thank you for sharing. It turned out really nice. I can’t wait to try this technique.
I'm loving it!! I can't wait to try it out. Thank you for turtoial 😃
Going to try this for my first wine glass. Amazing job as always!
beautiful!!! I learned something new today!!
Awesome look for sure..got to try it. Thanks for sharing!
This is beautiful!!!! Thank you for sharing this masterpiece!!!
Awesome, I've been wanting to give this method a try. Thank you for sharing.
My pleasure
That was amazing! I think I might have to try that as my first tumbler. BTW, great tutorial! Thanks.
Thank you so much!!!
OHHHHHHH AHHHHHHHH LOVVVVVVVVVVE THIS! THANKS FOR SHARING!
My pleasure!!
I love it can’t wait to make mine
This is soooo cool!!! Beautiful
Thank you for sharing it’s very pretty
This turned out very cute.
My smoke effects are rubbing off when I went to apply decal. I believe I followed your tutorial properly. Any advice would be greatly appreciated.
Ours did too so we sealed ours and put layer of epoxy on before decal.
I love your videos! I have been so afraid until I’ve come across yours. My question is though, wouldn’t one be afraid to hover a spray painted tumbler over the flame because of it being now flammable?
First time watching your channel, that was great I really enjoyed it.
Thank you so much!!
How cool!!!!! I have to try this!
Due to high demand in alcohol i cant find 91% alcohol. What percentage of alcohol can i use to prep my tumblers?
I managed to get some 71%
Should have just rubbed the big darker spot off. But turned out great and another idea for me.
Beautiful
Thank you for wearing the proper PPE! I only watch tutorials with those that demonstrate safe techniques. Your tutorial answered all my questions too! :)
Such a loss for you. They usually all wear the proper ppe while not doing videos. They only take the mask off so you can hear what they're saying. It really isn't right to pass this kind of judgement. You cost yourself valuable information.
You are very smart , love your creations
so cute!!
Hi. Where can i get a turner or how can I make one?
That a cool idea.i need to know what type of mask do you use ?
This is awesome
When would you add a little glitter after the decal or before you add the decal. Like epixy after smoke glitter and decal or how would you do it?
What type of respirator are you using? There are so many options. BTW, thank you for the tutorial! I have tried this and it isn’t easy!
Can you only do the smoke effect on the spray painted cup? No over epoxy?
what kind of clip do you have on your Turner. I have the same turner and i only have one so i get tired of taking the screw off and putting back on. Great tumbler !!
I replaced my screw with an R Key so I can easily remove my arm
Can you do smoke effect on an epoxied glitter base?
Yes
nice, im going to try this. how did you make the football arm ?
It is called a cup turner. Google it and plenty will pop up on Etsy
This is Awesome can you tell me what you have in the hole holding the rod onto the turner? I have a turner like this and the screw wants to sometime work it’s way loose Thank You!!
I replaced my screw with an RKey! :)
I love you turner. Does the arm (the pvc pipe with tumbler on it) remove from the stand easily?
I replaced my screw on the turner with an RKey can it can be easily removed
Do we need to clear spray the cup after smoke effect was done so the epoxy will not rub the smoke off? 🤔
Nope I didn’t seal the smoke with anything.
Amazing!
Did you seal the smoke in with an acrylic spray or anything? The smoke doesn't wipe off of you dont seal it?
I didn’t seal it. But, sealing never hurts. Any time I am in doubt of sealing a tumbler, I do.
Is it food safe? I see some tape the top so they paint/epoxy doesn't touch the mouth. I like it going to the top but want to make sure it is safe.
What is the pin called you have holding your rod on your tumbler?
What about a lighter colored smoke?
love this one, look fantastic and, i have same tumbler make noses does yours and get warm later too? i think mine warm from heat :( we have in Arizona get up to 110
They all get warm from turning that's normal
@@spiritwings4592 oh okay that good
If using a water slide should you epoxy first?
Did you let the spray paint gas off before burning it?
I let the spray paint dry before the smoke effect is applied
👍super neat,thank you!
Can you use denatured alcohol?
This tumbler is beautiful!
I have seen you mix epoxy in previous videos. Does your epoxy come with those squeeze tops, or are they a separate purchase?
The smaller bottles come with squeeze tops in the brand I use.
Make a fire/flame version.
So you’ve never had any issues not sanding your cups??? I’m still new, and I’ve seen so much mixed info, but I hate sanding cups!!
I haven’t. But, if you sand... it isn’t wrong. Use a 180 sanding block or paper
Hi how long do you wait for the smoke to “dry”
I think I will try holding it over a fire in the fire pit. thanks for the idea.
That would be awesome!!!
@@MissKissKreations weather was bad so did not try. But can you say tiki torch.............. it was the best!!!!!!! give it a shot. So much easier.
Please what is this router machine?
What can i use
So after you finish with the smoke effect, you don't need to clear coat spray it?
BTW.....I've been WAITING for you to do one of these....almost requested it the other day :) so thank you!
I used no sealer on this tumbler at all.
Smoked it, decaled it. Epoxied it.
And I take my requests very seriously!!! 🥰🥰🥰
@@MissKissKreations thank you!
I turn my first tumbler tomorrow. I have watched your vids over and over. Love how you explain everything you are doing. Acrylic tumbler will be my first...a little nervous!
I love this! Thank you for showing. Where did you get your cup turner?
Amazon. Noddway
@@MissKissKreations I ordered mine yesterday and will have it tomorrow. Can't wait to use it!! Thank you....
@@MissKissKreations Thank you! I ordered one yesterday and will have it tomorrow.
Can you use the powder coated color tumblers instead of the stainless ones?
You can. Powder coated are still stainless steel tumblers. I recommend sanding the powder coat very well before spraying or wiping down with alcohol
Please Give Me Your Advise: I for the life of me cannot apply epoxy correctly. I’ve watched your tutorials on epoxy over and over (as well as all your other tutorials). I ALWAYS end up with indentations. I’ve only tried Alcohol Inks, did not seal, applied epoxy. I always have to acetone. I use Alumalite Epoxy and I do torch. Any advice. I do everything your tutorials indicate. Thank You
Maybe you’re torching the epoxing, burning your epoxy. Or, if you’re using alcohol inks, it’s normal to have some bare spots on your tumbler from epoxy. Give it a light sanding, and epoxy over it, the epoxy shouldn’t repeal
Thank you ❤️
Hi if my tumbler after washing it when its completely finished comes up dull no shine where did I go wrong?? was my epoxy not mixed properly?♡ do all epoxy have to be clear before use cos mine has never been clear ☹☹it sat for 24hr. HELP!
My epoxy is never clear in the bottles but it usually turns clear when i mix the two parts
Did you mix the epoxy equal amounts and mix for 2 to 3 minutes?
Does i have to use 91% alcohol? The highest that I could find was 70% in my local store. Also thanks for the tip about reusing the transfer tape.
Yes. 91% is a must 70% isn’t strong enough to remove the oils. Try ordering the alcohol from Amazon
Can I do this after I have applied epoxy?
I haven’t tried it. I’m not too sure. Since the epoxy is slick and glossy. The smoke tends to stick better to the rough, matte finish
Miss Kiss Kreations thank you!! Love your videos!!
Do you have to epoxy or can you just use the dishwasher safe mod podge?
You have to epoxy if you want to keep the design on the tumbler. Mod podge will eventually come off.
Does thr apoxie or risen stink??? How long does it take to dry ect
Every epoxy brand is different. Some have no smell or harmful fumes. Drying times also differ with each epoxy brand.
How long are your football arms? 🤦♀️ My husband is in the process of building me a multi turner and I have only used the Hobby Lobby one. I'm not sure how long to make the detachable part.
I love your videos so I thought I'd ask you!
I buy a regular , uncut piece of pvc piping and I use a pipe cutter to cut mine down. I have them all different sizes depending on what I want them for, drying, hydro dip, spinning. They range from 12”-17”
Thank you!
Oh I bet you can take rubbing alcohol and wipe cup and restart if you need too
It'll take the spray paint right off, but I suppose you could just paint it and start completely over.
@@ladyakiraa82 true but it's worth the try
We have the same last name lol
Can this technique be used on a glass stemless wineglass?
Sure can! I have down plenty of stainless wine tumblers. I just don’t work on glass too often
How many coats of Epoxy did you do ?
Just one over the decal. :)
TFS do you know if this will work if I already epoxied my tumbler then decided to do this?
wondering the same thing!!!!
To be honest, I haven’t tried it! But, I’m now curious!
@@MissKissKreations Just FYI, I took the plunge and did it to my already epoxy cup and it worked perfectly, Thank you for your reply.
@@mrsdizi1234 awesome!!!! i plan to try tomorrow, thanks for letting us know (:
Are you not sanding your cup first? I've watched couple your videos and only heard say wipe it down with 91percent alcohol
I don’t typically sand. If you do sand, it isn’t wrong.
What did you use to print out the decal on?
I use a Cricut cutting machine
Is rustoleum better than Crylon
I have no personal preference. I go with what is available at the time
What Transfer tape do you use?
www.amazon.com/Frisco-Craft-4336883150-Transfer-Application/dp/B073XRLZ6Z/ref=mp_s_a_1_3?dchild=1&keywords=transfer+tape&qid=1587495237&sprefix=transfer+tape&sr=8-3
Interesting, thank you BUT get closer to the microphone because I am hard of hearing and couldn't hear you!!! Thanks again❤️
I’m glad I can help you and I’ll keep that tip in mind ☺️
Is that cup turner too fast or is it just me :P ?
There are different speed motors.
3/4rpm or 5/6rpm
I prefer the faster one. 5/6
At first I didn’t get it when you said you’re not going to use a spoon then I went ooooooohhhhhh 😂😂
Hahahaha. 😋
You should always sand been doing this 10years i know you say you dont so basically you can peel that epoxy right off.
I don’t sand my non powdered stainless tumblers. I have sanded some when I first started, just to see if there was a difference, for me, there wasn’t. Never has.
My epoxy has never peeled off any of them, as long as they have been cared for properly. Using the 91% alcohol and the flat spray paint helps the epoxy stick to the tumbler perfectly.
I don’t see a reason to waste time and money on materials that really isn’t needed, just suggested.
We have different methods and processes when creating, what works for you, may not work for me. And that is okay. You do what makes you feel best and I’ll do the same.
Thank you for your views.
I've been making tumblers for several years too. Never sanded or wiped with alcohol. Just spray paint for the base and I've never had any issues. 🤷🏻♀️
Can you use acrylic paint ?
I’ve never tried acrylic paint. But it is worth a try!
Don’t hold your tumbler so close to the flame
Lol