Sir in vedio at 21:15 ...there is pitch circle diameter to add..9.75 mm. But in my software which is 5.0 i m using There is option that is icon location.. I m not able to add diameter ...value...
Hello Satyendra, I learnt Creo just by watching your videos. Thank you very much for uploading these videos. I need to add thread dimensions in the family table. (for bolts and nuts). I tried several times, but did not succeeded. Can you please make a video on this.
your tutorial so valuable to understand much more about Creo, you are detailing each minute things very appreciatable Thank you so much Sir. I have a doubt coulf you please rectify..? What's the difference bet: datum centreline among sketch centreline..
This is a general practice. I am not sure whether it comes under ASME. Thread is something, no body design. Thread manufacturing is a standard process.
hai sir. i followed the same steps as you did. but even though I applied the cylindrical motion there is no movement for the nut or any movement for the assembly. why is it like that sir? any suggestions
Your explanation is so clear, which understand your video much easier. pls make more video like this . GOD BLESS U.
Sir in vedio at 21:15 ...there is pitch circle diameter to add..9.75 mm.
But in my software which is 5.0 i m using
There is option that is icon location..
I m not able to add diameter ...value...
same with me.... did you find the solution bro?
Check the motion symbol selection
thank you sir@@CADxTraining
Thanks sir for uploading such a good model
Hello Satyendra,
I learnt Creo just by watching your videos. Thank you very much for uploading these videos.
I need to add thread dimensions in the family table. (for bolts and nuts). I tried several times, but did not succeeded. Can you please make a video on this.
Thank you sir
Next request for Geneva mechanism with calculations
Sir, plzz make a Gd&t series. I love your teaching technique and it is amazing
I watch fulll advertising only for supporting you🙏🙏🙏
Sir when i am making hole of M10 size its diameter is showing 0.3543 in creo9.0.0.0
Same here , did you find any solution ?
Please tell how to set Start and end point thread of bolt and nut sett
Sir, please Make tutorials on Animation and Mechanisms
Agree
Thank you for the tutorial sir.It was very helpful.Can you please make one overview tutorial on dynamic constraint,connection and mechanism.
your tutorial so valuable to understand much more about Creo, you are detailing each minute things very appreciatable
Thank you so much Sir.
I have a doubt coulf you please rectify..? What's the difference bet: datum centreline among sketch centreline..
Sir if I want to use a bolt for mounting a body with base then which constraint is use?And how it's animated?
How can we use hatch colour from the 3D part in assembly drawing?
Hello sir the regenerate option is also not working hole is can't able to create only in small size😢
How did you know to use ∠75° and 0.500mm when you extended the helical cut transition thru?
70 to 75° is the industry practice.
@@CADxTraining will that angle work for me in ASME? Is there a Standard I can look up?
This is a general practice. I am not sure whether it comes under ASME. Thread is something, no body design. Thread manufacturing is a standard process.
@@solidkreate5007 sir how thread height is 0.5 mm
Thank you
Hello Satyendra! I hope all is well, waiting on a new video! Thanks and best wishes!
hai sir. i followed the same steps as you did. but even though I applied the cylindrical motion there is no movement for the nut or any movement for the assembly. why is it like that sir? any suggestions
Sir in the start of video, from which book have you taken drawings of nut and bolt
Drawing book from Gopalkrishna
thanks for the video bro. please upload videos on molds module..
Pls upload a video about how to create A3 sheet layout and BOM...
Sir aapne H value or nut ke length 26 mm kaisi nikali tutorial me kaha mention ki hai plz reply me i m confused about it
Please mention the time stamp from the video
@@CADxTrainingsir whole video dimensions confusion
All the time calculated based on M10 nut and bolt. You have all the formulas in the drawing placed on the left side in the video.
Beautiful thank you! Keep them spinning!
How to enable cabling tool in creo?
Open your assembly file first. Then go to application and cabling.
Pls make more video about mechanism.
Sir, Aap one video Unf TPI thread ke uper banaye, mujhe unf tpi ka calculations smjh me nhi aa rha he
Why in M10 hole dia changes to 0.35 when it should be 10 ?
Because your part unit is in inches
@@CADxTraining but I have changed model properties to MMKS still same.
Check the sketch dimension now. Now you delete the previous hole and re-create the hole
@@CADxTraining thank you sir it worked.
Glad to hear that
❤ thanks
Why save the file and then open it again in a new tab?
Write the timing from the video.
Hi how to contact you??? I have some professional work to be discussed.
Hi sri, please explain creo Stl file format
Mechanism not working properly. Also I set angular speed to 90 deg/sec but it isnt working fine...
Snapshot is not turning on
Try it one more time
I tried multiple times
How to change , to . ? Sir in dimension
Your question is not clear.
@@CADxTraining While iam giving thread dimensions it's showing 12,00 instead of 12.00
Sir Please share your maid id I will send some part model kindle to make that design.
sandesh4satyen@gmail.com
😵 Beginner 🥵
Hello sir,
Please make new videos
It's on the way.
@@CADxTraining thanks sir
Thank you