2021 Convid Crew Checking in - I just did this mod on my JDM Aristo V300 that had LED Tail Lights fitted from Japan. 100% works a treat! I de soldered one leg of the resistor and pried it up with a screw driver so it's 100% reversible if needed. Great video - easy done!
1998 LS400. Tail light warning failure, false indicator when all lights are operational. Old Lexus mechanic said 99% of tail light warnings are due to a burned bulb or a non-lexus bulb replacement. Sure enough, my mechanic replaced rear deck burned brake light with a generic bulb and dash warning stayed on. Bought a Lexus brake bulb at Lexus which my mechanic installed and surprise! Dash warning light went out, stayed out. For this car install only Lexus bulbs.
What's way over complicated, you can just disconnect or cut the wire off the harness at the sensor or under the steering column, either the wire that powers the sensor or the wire that feeds the lamp on your dash (same as cutting that resistor), if it hasn't changed, green/yellow goes to dash (pin 4) and red/cyan supplies the power to the sensor (pin 8) or you can remove the bulb off your dash.
I was getting annoyed over the warning light, too. I had replaced the rear brake lights and markers also and still had it on. Then, I put a stick to hold my brakes on and saw a third brake bulb out which I had not even noticed because it was on the side. I replaced it with the proper 194 bulb and it went out once the module reset. I assume the module detects wattage draws and would come on if bulbs were incorrect or out. Cool but unneeded feature.
Hello, I hve a 99’ LS. Looks like you hve on by the look of your profile. Could you help me in clipping the rite resistor?? The one in the video isn’t the same as mine for the LS. Hope to hear from you. -Aaron
thank you! I've got a 2000 ES 300...This sucker used to go on and off. when I popped the trunk..Now its on all the time and found i had a burned out bulb rear driver side..melted the housing..replaced the bulb..it gets hot?..and a bit brighter than the passenger side.?...Now the dash light is back to going on and off..I'd disconnect if i didn't think it was something else.Serious.. I've had it in the shop..They could not locate the problem.UGH..will see.
I bought the harness from Ebay. It uses the factory amp. If you want to use the radio speaker wires then you will need to cut the harness located on the factory amp, located behind the glove box.
That wood steering wheel definitely was put in by you.. Well I'm tryna do the same thing to mine I got the all black steering wheel .. Where'd yu get it from?? And where did yu order those taillights
The steering wheel is from an 01 or 02 RX300 (usually a lot cheaper than a GS woodgrain). Along with the single stage airbag (GS airbag doesn't fit.) The clear LED tail lights I bought from eBay.
its DEFINITELY the 3rd brakelight lol, i have a RX300, And you probably have to use a resistor for the tail light as well since the brake & tail lights are the same bulb lol
Hey I see you put speakers in Do you have a CD player also and can you get ahold of me what do I do in order to install a CD player it will not turn on when I install it
Can you shoot me a text 318-517-7415 I will explain it a little better basically I bought the harness took the factory out wire the harness to The new stereo and nothing I read that there is a amplifier you have to bypass
@K Y your video wasn't clear. But a simple yes or no would have also worked. Never understood why people have chips on there shoulder. Society is fucked up.
If you installed LED lights then it's not the box, the box is doing its job replacing it is just re-inviting the same issue.... However for the turn signal if you can replace the flasher module which i have video for
+BallinMafia I think so! A few times the car will make a beeping nose also and all the lights will turn on! I have a video, can I please send it to you, so you can hear it, and tell me what it is so I can get it fixed?
*MEANWHILE IN 2021...Ummm just disconnect the battery for 30 minutes, reconnect, and the ecu will recalibrate itself automatically ON ALL LEVELS* ( yes this works on 98-05 GS300/430 )
Or you can go out and buy the proper led programmed relays that fix the issue just by simply taking out the oem relay and plugging the new one in. I just don't understand the point of cutting up a Lexus and disabling a feature that now makes you manually check something when the new part will tell you the when your led is out.
BallinMafia imaginary? LMFAO really? Go ahead hit google real quick. Type in "Flasher relay" it's a real think. You can get them at oreillys. I should know cause it fixed my issue with my full led lights.
@K Y its not titled "how to fix your warning light" , its how to disable it. In the end, its your car you can do whatever you want to it. How about you make a video on how to get rid the warning light as you see fit.
2021 Convid Crew Checking in -
I just did this mod on my JDM Aristo V300 that had LED Tail Lights fitted from Japan.
100% works a treat!
I de soldered one leg of the resistor and pried it up with a screw driver so it's 100% reversible if needed.
Great video - easy done!
I'm so glad you found this pesky ass problem I switched all my lights to leds an didn't know what to do got if fixed now.....lol
1998 LS400. Tail light warning failure, false indicator when all lights are operational. Old Lexus mechanic said 99% of tail light warnings are due to a burned bulb or a non-lexus bulb replacement. Sure enough, my mechanic replaced rear deck burned brake light with a generic bulb and dash warning stayed on. Bought a Lexus brake bulb at Lexus which my mechanic installed and surprise! Dash warning light went out, stayed out. For this car install only Lexus bulbs.
This video helped me in 2019!
thanks, i did it to my 2004 IS300 Lexus and is just the way i want it, thanks again
Thanks man I really appreciate it, that tail light was sooo annoying
What's way over complicated, you can just disconnect or cut the wire off the harness at the sensor or under the steering column, either the wire that powers the sensor or the wire that feeds the lamp on your dash (same as cutting that resistor), if it hasn't changed, green/yellow goes to dash (pin 4) and red/cyan supplies the power to the sensor (pin 8) or you can remove the bulb off your dash.
Good video, thank you!!
Thank you Sir!
I was getting annoyed over the warning light, too. I had replaced the rear brake lights and markers also and still had it on. Then, I put a stick to hold my brakes on and saw a third brake bulb out which I had not even noticed because it was on the side. I replaced it with the proper 194 bulb and it went out once the module reset. I assume the module detects wattage draws and would come on if bulbs were incorrect or out. Cool but unneeded feature.
Helped alot. Thanks
Hello, I hve a 99’ LS. Looks like you hve on by the look of your profile. Could you help me in clipping the rite resistor?? The one in the video isn’t the same as mine for the LS. Hope to hear from you. -Aaron
thanks i really appreciate that
I have the same issue with my indicator light on my ES330. Was driving me nuts
Thank you bro
thank you! I've got a 2000 ES 300...This sucker used to go on and off. when I popped the trunk..Now its on all the time and found i had a burned out bulb rear driver side..melted the housing..replaced the bulb..it gets hot?..and a bit brighter than the passenger side.?...Now the dash light is back to going on and off..I'd disconnect if i didn't think it was something else.Serious.. I've had it in the shop..They could not locate the problem.UGH..will see.
Is it the same process for an 08 es350
Hey curious, where did you get your harness kit for the Screen? Did you have trouble with the wiring and bypassing the factory amp?
I bought the harness from Ebay. It uses the factory amp. If you want to use the radio speaker wires then you will need to cut the harness located on the factory amp, located behind the glove box.
BallinMafia
Awesome I appreciate the quick response !
oh and NICE VIDEO, but be easy on that circuit board scraping those solder points on the ground lol
That wood steering wheel definitely was put in by you.. Well I'm tryna do the same thing to mine I got the all black steering wheel .. Where'd yu get it from??
And where did yu order those taillights
The steering wheel is from an 01 or 02 RX300 (usually a lot cheaper than a GS woodgrain). Along with the single stage airbag (GS airbag doesn't fit.)
The clear LED tail lights I bought from eBay.
I'm got the 04 GS with the paddle shift thing I'm tryna figure out where I could get them from or did yu go to a junk yard?
All from eBay
How you know is this
Will it still pass smog
its DEFINITELY the 3rd brakelight lol, i have a RX300, And you probably have to use a resistor for the tail light as well since the brake & tail lights are the same bulb lol
Hey I see you put speakers in Do you have a CD player also and can you get ahold of me what do I do in order to install a CD player it will not turn on when I install it
Can you shoot me a text 318-517-7415 I will explain it a little better basically I bought the harness took the factory out wire the harness to The new stereo and nothing I read that there is a amplifier you have to bypass
will it work on a 2004 IS300 lexus?
Juan Alberto Diaz . Yes it should. the module is lightly different but basically the same circuitry.
Hey buddy, did you have a chance to see the video? The link is in the comments.
Did it effect anything else in the system?
No.
+BallinMafia Great,thanks gonna give it a shot!
@@johnnylrico How did it go?
Is that on the drivers side or passenger side
@K Y i know you are. Responding to a question i asked a year ago. Dumb ass
@K Y your video wasn't clear. But a simple yes or no would have also worked. Never understood why people have chips on there shoulder. Society is fucked up.
I had a much easier fix just cut a small square piece of black electrical tape and cover up the light.
I was thinking of removing the bulb in the dash
You could have done the same thing through the OBD port
What if I just replace that box u took out??
Tony Jones it depends on if the box is the problem or not. It could be the wiring, sockets or bulbs.
If you installed LED lights then it's not the box, the box is doing its job replacing it is just re-inviting the same issue.... However for the turn signal if you can replace the flasher module which i have video for
You just neutered your Lexus
Hey my Lexus 99 GS 300 is making a weird noise coming from the dashboard. Can I send you a video maybe you can help me?
sounds like a mouse crunching on soneting in there? If so then it is one your servo motors for your climate control making the sound.
+BallinMafia I think so! A few times the car will make a beeping nose also and all the lights will turn on! I have a video, can I please send it to you, so you can hear it, and tell me what it is so I can get it fixed?
+BallinMafia did you get a chance to see the video I linked you with?
+PS3isKing123 No, I dont know where you sent the video.. Why not upload to youtube?
PS3isKing123 .it's the motors that change the a.c.positions.they get stuck.i unplugged mine.
*MEANWHILE IN 2021...Ummm just disconnect the battery for 30 minutes, reconnect, and the ecu will recalibrate itself automatically ON ALL LEVELS* ( yes this works on 98-05 GS300/430 )
well guess I'm doin that to mine today
Ppl check the third brake light!
Nah when you switch from halogen to LED on the 3rd brake light it triggers the warning light even with resistors
I just cut the blue wire running to the harness... took me all of 30 seconds...
Yep, just cut mine an light gone 😎
@Kuntryboyz Car Club did it work?
This is extreme 😂🤦🏾
Why not find out why you are getting the warning?
Because, fuck that warning light. Lol
What’s the warning light for? Just letting you know your shits bright?
enrique mejia it is supposed to indicate that you have a blown bulb.
BallinMafia oh that’s pretty dope
Or you can go out and buy the proper led programmed relays that fix the issue just by simply taking out the oem relay and plugging the new one in. I just don't understand the point of cutting up a Lexus and disabling a feature that now makes you manually check something when the new part will tell you the when your led is out.
LED programmed relays? lol. Too funny. Your just making up imaginary parts.
BallinMafia imaginary? LMFAO really? Go ahead hit google real quick. Type in "Flasher relay" it's a real think. You can get them at oreillys. I should know cause it fixed my issue with my full led lights.
You did not say "flasher relay". And no, a flasher relay will not make the warning light on a GS300 go away.
BallinMafia worked for me. I assume it'd be to same for everyone else.
@K Y its not titled "how to fix your warning light" , its how to disable it. In the end, its your car you can do whatever you want to it. How about you make a video on how to get rid the warning light as you see fit.
Why drive a Lexus, if you have to strip its features.
Only rich people drive Lexus
Huh?
lexus its same toyota....just for USA market...so rich ppl drive toyotas? :)
We rich and do what the fuck we want brah
(lol)
Very poor video as you cannot see what he is doing or even where he is working