I know this video is a few years old, but here goes. I've had a glue gun since 2000 that's worked wonders. Lately though, I've noticed glue back flowing where the glue stick gets pushed in. I pulled it all apart and cleaned out that area, but it still seems to be doing it. The glue stick doesn't seem to want to move forward sometimes. So I bought a new glue gun at the dollar store today (I bought this one at a dollar store in 2000). The new one just doesn't seem to heat up the glue sticks, they come out in this thick blob, where my old one heats them up nicely, it just has this new issue now. suggestions? I was wondering if maybe the glue sticks are too small? but i've used these before. So I figure they should be fine. The glue sticks are listed as "all purpose" for use with high, low, and dual guns.
I still answer questions! It's possible it's the circumference of the glue sticks that are giving you problems, but as ling as the gun is trying to catch when you squeeze the trigger, it's probablynot that . Not sure if you're in the US, but the quality in the dollar store glue guns has gone way down. My only suggestion (other than buying a craft store glue gun) is to try low temp sticks they have the most wax, so also have the lowest melting point. Hope that helps.
@@MakerHighSchool It catches the glue stick, but as the glue stick gets to the end of it's life, it starts to all clog up and the next one doesn't advance very well. I can usually force the next one in and it will start to go again. I might try the new glue gun with low temp glue to see how that works. Thanks.
Hi. I bought a brand new glue gun with glue sticks in the kit. I inserted the first glue stick and it did not insert all the way even if i used the trigger to push it forwatd. So as the instructions say to insert a second glue stick behind it to push the first glue stick into the chamber. I turned on the glue gun and ended up with the first glue stick bending at the back while the second glue stick attempted to push the first one through. What do i do now? Can i cut the bent piece off while it is cold? Will that help? Wish i could upload a photo here, but can't see a way to do that.
From what I'm picturing, yes, I'd cut it off if you can. (While it's cold and unplugged) put in the second glue stick and try again. (The risk is you might break the assembly inside.) Since it's new, if that still doesn't work, you can always return it. Best of luck!
I just bought it, opened it and put the glue stick that was inside the box. So it's got to be the right quality. I pressed inside as far as it goes. Not working and glue is not coming out. How do I get the stick out
You should honestly exchange it for a new one. It means your heating element isn't getting hot enough. If that's not an option, best case scenario is turn it on and let it sit for 5 + minutes. You can unplug it and pull it out of the back. I DO NOT recommend since you can break the assembly and leave glue behind in the barrel. If that doest work, it means your heating element is totally shot. Be careful not to shock or burn yourself.
My glue gun worked before on the sticks I have rn but now it's not working. I tried to look inside the glue gun and I saw the stick there. The stick is not melting. Do I have to Unscrew the glue gun to get the stick out?
It depends. I have a video showing the inside of a glue gun. If the glue is stuck in the heating element, it's dead because it's not getting hot enough to melt the glue. If you do decide to open it, make sure to unplug it first. 👍
My glue gun gets super hot but nothing comes out! Left it on by accident could that be why? It worked just fine before! I use a high temp project pro with crystal clear stix
My glue gun is working absolutely perfect but, when i stick two object together and when the glue dries up and cools down, the objects can be pulled apart so easily as if they had never been stuck with hot glue in the first place.... How do I ensure this doesn't happen
without knowing what you're trying to glue, I can only guess. Hot glue isn't always the best adhesive for some materials. I have videos about a couple of other glues that might work better, or you could check out the website thistothat.com to get a recommendation for the type of glue to use to glue two surfaces together.
you have a most beautiful smile! Thanks for this tips that many may think or redundent, I found out info I did not know about. And I have been doing this a long time.
My glue gun is only three days old but first and second day it worked too good but third day when I used it , it heats completly hot but when I press the trigger only one drop of glue is coming out please help my money will be wasted😢😭😤 and it's 40 Watts and I bought it online on flipkart
Flipkart doesn't have the best reputation. Might be the spring on your trigger. IF you're an adult, you can take a look at my video "how a glue gun works". Make sure you UNPLUG it if you decide to open it up. If the spring is still attached where it should be, you might want to try replacing it if there's a spare one lying around. Hope this helps!
I think I know now why my glue gun does what it does. None of what you said here is what I'm experiencing. My glue stick melte inside the glue gun,making it come out before the nozzle! Crazy, right? I bought the sticks from a Chinese store,now I know why I'm having these problems. Maybe the stick are for a low heat gun and mine is too hot. Thanks. I won't buy glue stick anymore unless they're quality ones
First my Glu gun was working properly and now glue is taking a lot of tim e to com out and th n also just a drop come pl tell once mam the correct solution
My glue gun was working perfectly until the wax went in , now the glue doesn't even come out...and if it does ...only a drop or so.. plz help (it's a hot melt glue gun)
Sounds like the heating element is shot. Could have overheated or faulty connections with the wires. I'd return it and get a different brand if possible. Sorry.
My glue gun keeps making little bubbles and every time I try to heat it up it never works and I do remember that someone in my house put a crayon inside of it maybe that’s the problem I don’t really know
I'm pretty sure that's the problem. Glue sticks are a mixture of plastic and wax. Crayons are wax and other things like hard minerals to color them, and additives to make them glide easier. The wax melts faster than a glue stick and leaves behind everything else, and that clogs the glue gun. That sucks, sorry. I've had a lot of people on my glue gun burn video comment they did it with crayons in the gun. At least no one got burned badly. I'm afraid you're going to have to buy a new glue gun since it's next to impossible to get inside the barrel. I have a video showing what the inside of a standard glue gun looks like if you want to know what I'm talking about. Stay safe! Best, Lori
If you've checked to make sure you have the right glue sticks, try plugging it into another outlet. If it still isn't working, return it for a new one.
My glue gun is brand new and the first time I tried using it the glue wouldn’t come out. I know it is heating because the nozzle was really hot and the glue stick I was using came with the gun. Do you know what is wrong?
You could try letting it sit a little while longer while it's heating up and then possibly pushed gently from the back of the glue stick. Don't go too hard could because you don't want to break the trigger. If it still won't move, then there's a problem with your heating element, probably. I'd return it and exchange it for a different kind.
If you've tried using low temp glue sticks and it still won't work, the problem is either your outlet or the gun itself. Try it in a couple different rooms and if it's a no go, it's the gun. I'd exchange it for a different brand if possible. Hope that helps! 👍
I have a brand new glue gun with the matching glue sticks that came with it. It takes 15 minutes to get 1 inch of glue out. Its a regular size gun. This is the 3rd larger gun I've bought, tried multiple rooms/outets. My mini works just fine in same spot. I'm seriously losing my mind.
I wait until glue start coming out of my gun but when i trigger it,the glue stick dont move forward and when i leave the trigger it go half way back and get stuck
funny, i git the adtech high temp glue gun and multi temp glue sticks and discovered i bought a piece of crap, i wait 5 mins and when i go to use it i get a short burst of an inch or less on the first attempt and then have to wait another 5 mins and i get a few drops the second time, on third try after waiting i got nothing. the gun came with no instructions except for the little bit on plastic wrapper and it didn't specify any type of glue stick other than to say full size so i do believe its going in the trash.
Ad tech has been going down hill lately. If you can return it and get your money back, that's the best option. If the store gets too many returns, it will stop carrying that item. That's usually how manufacturers get the message that people aren't going to support their bad products. 👍
My hot glue was working perfectly but it is not working now i can feel heat but the glue is not coming the stick is perfect and some times the glue come from every were help me pls..........
If the glue is coming from everywhere, it sounds like you either have a clog or a problem with the trigger. I have another video showing the inside of a glue gun. ONLY open it up if you are an adult. If you open it up, MAKE SURE it is unplugged. The spring tension may be off. If it's not the spring, then it's a clog on the inside of the heating element. Hope this helps!
If you've waited for more than 5 minutes, and you've getting no melting at all, try a different outlet to make sure enough power is coming through. If it's still not working, it's probably the heating element in the glue gun. I'd return it and get a different brand. Hope that helps.
Are you using the glue sticks that came with it? If so, then the heating element isn't heating up to temp. First, try a different outlet, just to make sure it's getting full power. If that doesn't work, I'd suggest returning it, and getting a different brand if possible. (If that one has a defect, chances are the others do, too.)
You might want to try a different outlet, to make sure it's getting enough power. Otherwise, the heating element might be toast, and you'll just have to get a new one. Sorry.
Hmmm...try a different outlet. If it still isnt melting, it's probably your heating element. I'd exchange it for a new glue gun if you can. (Make sure you get glue sticks made for specific glue gun as well.)
Ilda Tachim That's odd. I've never had a problem with that brand. Is it a large or small gun? Also, how long are you letting it heat up before using it? It's not going to be the trigger or the sticks in this case.
I would check to make sure your outlet isn't the problem. Have you tried plugging it into a different outlet? If it's still not heating up, the glue gun has to be defective. I'd return it and buy another kind. Not heating up at all sounds like a connected problem to the heating element.
You can try plugging it into a different outlet and see if that helps, or switching to low temp glue. It sounds like your heating element is the problem. If neither of those things work, I'd return it and get a new one.
The shop from which I bought it was closed so I went to another shop and there the Glue gun was heating but the glue was not coming out so the shopkeeper said that the nozzle is jammed
It sounds like the heating element is about to give out. You might want to trying switching plugs to make sure its getting enough power. If that's not the problem, you might want to consider buying a new one.
![[UA] NAVI vs MOUZ | BO5 | IEM Rio 2024](http://i.ytimg.com/vi/CMBYk0cbGoA/mqdefault.jpg)
I know this video is a few years old, but here goes.
I've had a glue gun since 2000 that's worked wonders. Lately though, I've noticed glue back flowing where the glue stick gets pushed in. I pulled it all apart and cleaned out that area, but it still seems to be doing it. The glue stick doesn't seem to want to move forward sometimes.
So I bought a new glue gun at the dollar store today (I bought this one at a dollar store in 2000). The new one just doesn't seem to heat up the glue sticks, they come out in this thick blob, where my old one heats them up nicely, it just has this new issue now.
suggestions?
I was wondering if maybe the glue sticks are too small? but i've used these before. So I figure they should be fine.
The glue sticks are listed as "all purpose" for use with high, low, and dual guns.
I still answer questions! It's possible it's the circumference of the glue sticks that are giving you problems, but as ling as the gun is trying to catch when you squeeze the trigger, it's probablynot that
. Not sure if you're in the US, but the quality in the dollar store glue guns has gone way down. My only suggestion (other than buying a craft store glue gun) is to try low temp sticks they have the most wax, so also have the lowest melting point. Hope that helps.
@@MakerHighSchool It catches the glue stick, but as the glue stick gets to the end of it's life, it starts to all clog up and the next one doesn't advance very well. I can usually force the next one in and it will start to go again. I might try the new glue gun with low temp glue to see how that works. Thanks.
My glue gun is taking alot of time for the glue to come out and still comes only a drop
Is it a high temp or low temp gun?
Sames happening with me
@@MakerHighSchool
It is of 60 w and it comes like a drop after half hours and the glue stick is high quality
@@MakerHighSchool please help me 😭😭
@@yourlocaltheatrekid900 I'd try a different brand of glue stick.
Hi. I bought a brand new glue gun with glue sticks in the kit. I inserted the first glue stick and it did not insert all the way even if i used the trigger to push it forwatd. So as the instructions say to insert a second glue stick behind it to push the first glue stick into the chamber. I turned on the glue gun and ended up with the first glue stick bending at the back while the second glue stick attempted to push the first one through.
What do i do now? Can i cut the bent piece off while it is cold? Will that help? Wish i could upload a photo here, but can't see a way to do that.
From what I'm picturing, yes, I'd cut it off if you can. (While it's cold and unplugged) put in the second glue stick and try again. (The risk is you might break the assembly inside.)
Since it's new, if that still doesn't work, you can always return it. Best of luck!
I just bought it, opened it and put the glue stick that was inside the box. So it's got to be the right quality. I pressed inside as far as it goes. Not working and glue is not coming out. How do I get the stick out
You should honestly exchange it for a new one. It means your heating element isn't getting hot enough.
If that's not an option, best case scenario is turn it on and let it sit for 5 + minutes. You can unplug it and pull it out of the back. I DO NOT recommend since you can break the assembly and leave glue behind in the barrel. If that doest work, it means your heating element is totally shot. Be careful not to shock or burn yourself.
My glue gun worked before on the sticks I have rn but now it's not working. I tried to look inside the glue gun and I saw the stick there. The stick is not melting. Do I have to Unscrew the glue gun to get the stick out?
It depends. I have a video showing the inside of a glue gun. If the glue is stuck in the heating element, it's dead because it's not getting hot enough to melt the glue. If you do decide to open it, make sure to unplug it first. 👍
Didn’t know there where different kinda of hot glue sticks. I thought they where all the same.
How can I tell if my glue gun takes high temp glue sticks or low temp glue sticks?
If you don't remember, I'd suggest using Google lens to search for it online. It's way easier. 👍😆
I got a new dual temp glue gun , but the glue is not coming out. What to do?
Try low temp sticks.
My glue gun gets super hot but nothing comes out! Left it on by accident could that be why? It worked just fine before!
I use a high temp project pro with crystal clear stix
Could be. You might have burnt it out.
My glue gun is working absolutely perfect but, when i stick two object together and when the glue dries up and cools down, the objects can be pulled apart so easily as if they had never been stuck with hot glue in the first place....
How do I ensure this doesn't happen
without knowing what you're trying to glue, I can only guess. Hot glue isn't always the best adhesive for some materials. I have videos about a couple of other glues that might work better, or you could check out the website thistothat.com to get a recommendation for the type of glue to use to glue two surfaces together.
you have a most beautiful smile! Thanks for this tips that many may think or redundent, I found out info I did not know about. And I have been doing this a long time.
I am so pleased to hear that! Sorry I didn't respond sooner, but I was working on the video I put up today. ❤👍
How do I know if my gun is high melt or low melt?is there different wattages? ( or whatever)
That's what I want to know, too. I don't know if my gun is a high temp gun or a low temp gun
My glue gun is only three days old but first and second day it worked too good but third day when I used it , it heats completly hot but when I press the trigger only one drop of glue is coming out please help my money will be wasted😢😭😤 and it's 40 Watts and I bought it online on flipkart
Flipkart doesn't have the best reputation.
Might be the spring on your trigger. IF you're an adult, you can take a look at my video "how a glue gun works". Make sure you UNPLUG it if you decide to open it up. If the spring is still attached where it should be, you might want to try replacing it if there's a spare one lying around. Hope this helps!
I think I know now why my glue gun does what it does. None of what you said here is what I'm experiencing. My glue stick melte inside the glue gun,making it come out before the nozzle! Crazy, right? I bought the sticks from a Chinese store,now I know why I'm having these problems. Maybe the stick are for a low heat gun and mine is too hot. Thanks. I won't buy glue stick anymore unless they're quality ones
I have small one what should I do??
First my Glu gun was working properly and now glue is taking a lot of tim e to com out and th n also just a drop come pl tell once mam the correct solution
My glue gun was working perfectly until the wax went in , now the glue doesn't even come out...and if it does ...only a drop or so.. plz help (it's a hot melt glue gun)
Did you put a stick of just wax in it? I'm guessing it's a high temp glue gun?
I used the glue refill or the wax that was provided
Sounds like the heating element is shot. Could have overheated or faulty connections with the wires.
I'd return it and get a different brand if possible. Sorry.
My glue gun keeps making little bubbles and every time I try to heat it up it never works and I do remember that someone in my house put a crayon inside of it maybe that’s the problem I don’t really know
I'm pretty sure that's the problem. Glue sticks are a mixture of plastic and wax. Crayons are wax and other things like hard minerals to color them, and additives to make them glide easier. The wax melts faster than a glue stick and leaves behind everything else, and that clogs the glue gun. That sucks, sorry.
I've had a lot of people on my glue gun burn video comment they did it with crayons in the gun. At least no one got burned badly. I'm afraid you're going to have to buy a new glue gun since it's next to impossible to get inside the barrel. I have a video showing what the inside of a standard glue gun looks like if you want to know what I'm talking about.
Stay safe! Best, Lori
My glue gun is not working.. its new and glue is not coming out.. what yo do?
If you've checked to make sure you have the right glue sticks, try plugging it into another outlet. If it still isn't working, return it for a new one.
I had small glue gun and it takes too much of time to come out and it comes only one one drop what shall i do
Is it a high temp or low temp glue gun?
My glue gun is brand new and the first time I tried using it the glue wouldn’t come out. I know it is heating because the nozzle was really hot and the glue stick I was using came with the gun. Do you know what is wrong?
You could try letting it sit a little while longer while it's heating up and then possibly pushed gently from the back of the glue stick. Don't go too hard could because you don't want to break the trigger. If it still won't move, then there's a problem with your heating element, probably. I'd return it and exchange it for a different kind.
Thank you we returned it and got a different beand
Hope this one works out better for you. Let me know!
Yea the new one is very good! Thanks for your help 🙂
Awesome! Pleased to hear that. Just leave a comment if I can help with anything else. 👍
My glue gun is duel temp and brand new but melted glue won't come out
If you've tried using low temp glue sticks and it still won't work, the problem is either your outlet or the gun itself. Try it in a couple different rooms and if it's a no go, it's the gun. I'd exchange it for a different brand if possible. Hope that helps! 👍
I have a brand new glue gun with the matching glue sticks that came with it. It takes 15 minutes to get 1 inch of glue out. Its a regular size gun. This is the 3rd larger gun I've bought, tried multiple rooms/outets. My mini works just fine in same spot. I'm seriously losing my mind.
it is working but it is coming only like drop it is not coming like fast
Is it a high temp or low temp glue gun?
@@MakerHighSchool high temp 60 w
I wait until glue start coming out of my gun but when i trigger it,the glue stick dont move forward and when i leave the trigger it go half way back and get stuck
sounds like the heating element is broken. I'd exchange it for a different brand
Thank-you!
You are most welcome!
Why my glue doesn't come out of it but the gun is heating? please help I have brought before two days only
are you using the glue that came with the gun? you might have the wrong kind of glue sticks.
funny, i git the adtech high temp glue gun and multi temp glue sticks and discovered i bought a piece of crap, i wait 5 mins and when i go to use it i get a short burst of an inch or less on the first attempt and then have to wait another 5 mins and i get a few drops the second time, on third try after waiting i got nothing. the gun came with no instructions except for the little bit on plastic wrapper and it didn't specify any type of glue stick other than to say full size so i do believe its going in the trash.
Ad tech has been going down hill lately. If you can return it and get your money back, that's the best option. If the store gets too many returns, it will stop carrying that item. That's usually how manufacturers get the message that people aren't going to support their bad products. 👍
How do I know that my glue stick is high temp or low temp?
It's in one of my videos. It depends on how "clear" they are. Cloudier/opaque means more wax, so low temp. 👍
I don't know which type of glue gun I have. What to do? And I think I?have a higher level of glue sticks than the gun. Just need your assurance
It used to work the glue sticks came with the glue gun but all of a sudden it's not working helpp!
Are you using new glue sticks?
Same problem dude!
@@kirtigarodia6591 Are you using new glue sticks.
How to clean glue gun inside part without opening it
You can't. Get a new one.
My hot glue was working perfectly but it is not working now i can feel heat but the glue is not coming the stick is perfect and some times the glue come from every were help me pls..........
If the glue is coming from everywhere, it sounds like you either have a clog or a problem with the trigger. I have another video showing the inside of a glue gun. ONLY open it up if you are an adult. If you open it up, MAKE SURE it is unplugged. The spring tension may be off. If it's not the spring, then it's a clog on the inside of the heating element. Hope this helps!
There is no problem like clog or in trigger and now the pressing button is not working and i think the hot glue gun is stuck help me pls.............
Hello
Why won't my glue gun light stay on or charge
If it runs on a battery pack, the battery might be dead.
What if its a new gun and you're using the right glue
If you've waited for more than 5 minutes, and you've getting no melting at all, try a different outlet to make sure enough power is coming through. If it's still not working, it's probably the heating element in the glue gun. I'd return it and get a different brand. Hope that helps.
How my glue gun is not getting hot I have tried with my new glue stick plss help me
Try checking on a different outlet. If not, the wires are probably bad. You will need a new one.
@@MakerHighSchool thanks I have tried and why at any time I have to use different outlet
Because sometimes the electricity might be the problem. If the outlet stops getting enough power, it can't start the glue gun.
@@MakerHighSchool ok thanks a lot
My glue gun is heating but the glue stick is taking a long time to melt though it is melting bit it's not coming out its a new gun
Are you using the glue sticks that came with it? If so, then the heating element isn't heating up to temp.
First, try a different outlet, just to make sure it's getting full power. If that doesn't work, I'd suggest returning it, and getting a different brand if possible. (If that one has a defect, chances are the others do, too.)
Thanks
My glue gun doesn't getting bot i plug it for 15-20 min but not littel hot help plZzz
You might want to try a different outlet, to make sure it's getting enough power. Otherwise, the heating element might be toast, and you'll just have to get a new one. Sorry.
Same problem bro
@@marysunil9314 Then I'd suggest the same thing. 👍
That sucks I got multi temp glue sticks with a low temp gun😭 its taking forever
Yep, but once you're done, you know what to get for the next batch. 👍
My glue gun is new and it’s on high temp and the glue still won’t melt
Hmmm...try a different outlet. If it still isnt melting, it's probably your heating element. I'd exchange it for a new glue gun if you can. (Make sure you get glue sticks made for specific glue gun as well.)
I bought another one but still have the same problem mine is a surebonder glue gun
Is it a high temp or low temp gun?
high temp
Ilda Tachim That's odd. I've never had a problem with that brand.
Is it a large or small gun? Also, how long are you letting it heat up before using it? It's not going to be the trigger or the sticks in this case.
large . Once, I left it for over 1hr and it was cold
I would check to make sure your outlet isn't the problem. Have you tried plugging it into a different outlet? If it's still not heating up, the glue gun has to be defective. I'd return it and buy another kind. Not heating up at all sounds like a connected problem to the heating element.
I am waiting for 30 mins but glue does not come out .!!!
You're either using the wrong kind of sticks, or your gun isn't heating up.
@@MakerHighSchool thank you . I went to the shop they said I need to put a little bit pressure in the trigger.
My hot glue gun is taking 10 minutes to complete 2 centimetres
I have a high temp glue gun but still I am facing the same problem
You can try plugging it into a different outlet and see if that helps, or switching to low temp glue. It sounds like your heating element is the problem. If neither of those things work, I'd return it and get a new one.
I tried it but it would not work so I am planning to return it back
The shop from which I bought it was closed so I went to another shop and there the Glue gun was heating but the glue was not coming out so the shopkeeper said that the nozzle is jammed
my hot glue gun is not working and it's of 60 w
Is it getting hot? Is the glue melting?
My glu gun stick melt in inside how to clean
I'm not sure that you can.
my glue gun is not work please help me
That's a little too general to be able to help. I have a whole playlist to help troubleshoot. It should be covered in at least one of the videos.
manelord kit brand new not working
I'd take it back. Probably faulty wiring.
Mine is a dule one
It sounds like the heating element is about to give out. You might want to trying switching plugs to make sure its getting enough power. If that's not the problem, you might want to consider buying a new one.
My hot glue gun first day ok but second day no heat not come the gum
It's not coming
If the video didn't help, sounds like its broken. That sucks. Sorry.
@@MakerHighSchool I am saying that glue is not coming from gun
My hot glue gun first day ok but second day no heat not come the gum
sounds like the heating element is broken. I'd return it and get a new one