Love the video... I was in stitches when we got to the case smashing sequence. I've got a vintage 18 century grand French clock - think you can change the springs in it ? :-)
Yes my friend i can change the springs, dismantling or replaice the bearings , the job for me is too hard.sorry for late replay all the best to you. jose
There's a band in the rubber seal you need to get screwdriver under it without damaging the rubber and pry it. Pig of a design but easy enough when you do it a few times
ElectronicDeLuxe thank for the reply but already solve the problem i have made the repair !works fine so far dont know a long will last but i have use it about 10 times untill now zero leaks!!
Eric M. Check my videos on UA-cam I got a video there similar to the repair that I did its in Russian u see a guy in underwear fixing the machine mine was a little different just one detail
12:00 I tried to open the screw but the t40 bit has broken.. The screw was to tight.. I did remove the water pump and the motor.. I can use the water pump to my fish tank.. And with the motor I'm thinking to build a big blender to make compost from food waste.. 😉
Replacement drum is £130 and its a complete unit. Also the spider on the back of drum doesn't look very strong. Get yourself an older bosch; much stronger drum which is £110 and the drum housing splits in half so you can replace the bearings.
alphatango311 there's tutorials all over UA-cam how to separate the drum. I followed one video and changed the bearings on my hotpoint with the same drum as this one
Most problems with washing machines not spinning or flashing lights refers to an object obstructing the small motor draining water from tumble. This is how to fix it yourself avoiding paying ridiculous money to an "engineers"Remove water manually from inside thee tumble, then remove the front bottom cover of the w/machine, unscrew the plastic cap, removing it completely, prepare a towel to collect remaining water, allow all water to come out making sure there is no remaining loose objects inside. Put the plastic cap back tightening correctly. If after doing that problem remains, then call an engineer.
Mine has the same problem , I was thinking doing the same with mine, what level of DIY you would say this is , I'm not very good at dismantling things, but I'm pretty good with a hammer ? :D
kar volt videora venni hogy hibas a csapagy,azt mar szetbontas szetveres elott tudtuk.Arra lettem volna kivancsi,hogy az ustot hogyan bontja szet,hogy csapagycsere utan hasznalhato mosogepe legyen az ugyfelnek...
ну можно было шуруповёртом мелкие отверстия проделать и за тем лобзиком распилить по месту где он был запаян затем закрутить бяку выбить барабан и за тем бак перевернуть и выбить подшипники и заменить их затем также собрать одеть барабан промазать силиконом сутки подождать и завернуть короткие саморезы и всё поставить его в машину подсоединить и проверить течёт он или нет но лутше новую машинку купить
How did you manage things put back together again?
Love the video... I was in stitches when we got to the case smashing sequence.
I've got a vintage 18 century grand French clock - think you can change the springs in it ?
:-)
Yes my friend i can change the springs, dismantling or replaice the bearings , the job for me is too hard.sorry for late replay all the best to you. jose
Great. You showed everything but the bit I wanted.
How did you remove the rubber from the front door opening?
There's a band in the rubber seal you need to get screwdriver under it without damaging the rubber and pry it. Pig of a design but easy enough when you do it a few times
What model is this washing machine?
Indesit WIXXE 127
Can you please tell me the number of the front bearing? I have almost the same washing machine. On back i can read 6202zz. Thank you
This can be repaider. Cut plastic in 1/4 from back , replace bearings , solder plastic. Price in Poland about 40 Euro.
any way to open the plastic cover that without breaking?i got that problem
Hi, there is no way of changing the bearings in thse without changing the whole drum unit.
ElectronicDeLuxe thank for the reply but already solve the problem
i have made the repair !works fine so far dont know a long will last but i have use it about 10 times untill now zero leaks!!
+Cebola Px Hi, how did you repair the drum unit please ?
Eric M. Check my videos on UA-cam I got a video there similar to the repair that I did its in Russian u see a guy in underwear fixing the machine mine was a little different just one detail
12:00 I tried to open the screw but the t40 bit has broken.. The screw was to tight.. I did remove the water pump and the motor.. I can use the water pump to my fish tank.. And with the motor I'm thinking to build a big blender to make compost from food waste.. 😉
Я думаю,что ломать бак не было необходимости и столь долго показывать отработавшие ресурс подшипники то же.Любой мастер видел это даже не десятки раз.
Replacement drum is £130 and its a complete unit. Also the spider on the back of drum doesn't look very strong. Get yourself an older bosch; much stronger drum which is £110 and the drum housing splits in half so you can replace the bearings.
hi all... thanks for watching my video.that model machine nobody can replaice the bearings only new wole drum unit. new drum cost 150 pounds.
alphatango311 there's tutorials all over UA-cam how to separate the drum. I followed one video and changed the bearings on my hotpoint with the same drum as this one
The Traitorous Gamer
Hi how did you get the drum apart ?
Regards
Davy Thomas
Point taken...not really serviceable is it.
Most problems with washing machines not spinning or flashing lights refers to an object obstructing the small motor draining water from tumble. This is how to fix it yourself avoiding paying ridiculous money to an "engineers"Remove water manually from inside thee tumble, then remove the front bottom cover of the w/machine, unscrew the plastic cap, removing it completely, prepare a towel to collect remaining water, allow all water to come out making sure there is no remaining loose objects inside. Put the plastic cap back tightening correctly. If after doing that problem remains, then call an engineer.
Mine has the same problem , I was thinking doing the same with mine, what level of DIY you would say this is , I'm not very good at dismantling things, but I'm pretty good with a hammer ? :D
with hammer? hahaha, good one dear. thanks for comment, all the best.
Ah there’s no problem that can’t be sorted with a big hammer. 🤪⚒🧨
kar volt videora venni hogy hibas a csapagy,azt mar szetbontas szetveres elott tudtuk.Arra lettem volna kivancsi,hogy az ustot hogyan bontja szet,hogy csapagycsere utan hasznalhato mosogepe legyen az ugyfelnek...
ну можно было шуруповёртом мелкие отверстия проделать и за тем лобзиком распилить по месту где он был запаян затем закрутить бяку выбить барабан и за тем бак перевернуть и выбить подшипники и заменить их затем также собрать одеть барабан промазать силиконом сутки подождать и завернуть короткие саморезы и всё поставить его в машину подсоединить и проверить течёт он или нет но лутше новую машинку купить
??????
да и тем более индезитовский бак запаянный на заводе так что лучше новую машинку купить
I will just throw my machine down the stairs and get a new one save the trouble of wrecking it in my kitchen as in this video
Don't bother fixing to it will just be the same even if you do fix it
You ruind a perfect washing machine.
у меня точно такая же машинка была и та же самая проблема была вызвали мастеров сказали они ремонт обойдёться в 7 тысяч рублей
потшипники расыпались и сальник начал пропускать воду
Why is there so many dislikes?
23:32 didn't spell Bosch proppoly
Прям решил проблему . Расхерачил бак к черту, гений ...ть
А как по другому когда бак паянный? Не всем всралось 200 лет пилить его и еще 200 складывать обратно проще новую машинку купить!
Ah the good old washing machine repair specialist, probably works for curry's
Мастер рукожопый, подшипники изломал, бак расколотил.
I fix cars tol
I think the author dropped a hint... Just buy a new one!
Calm doon neebs
Hit it ha ha
Another person who thinks they can do informative UA-cam videos by just smashing something up. Bloody ridiculous
Why bother posting this video?
This video is a waste of time does not tell you how to dismantle it properly or put it back together again