How to make an Inductor 30Amps 60Amps

Hi friends in this video i will show you how to make an inductor .
It's very simple to make an Inductor . but it is very tricky to get the right amount of inductance . i accidentally used Farrarite Core instead of iron Powder core . and results 10× higher Inductance. so i got not 200uH but 2000uh. so i recommend to use Iron Powder core not Farrarite core . i made this 30A and 60A inductor for High power boost converter. and Buck converter.
#coil #how does an inductor work #inductor basics #inductor inductor circuit analysisinductor coilinductor tutorialinductor voltage inductors in circuits

[@Electronic_For_You]

⚠️ WARNING ⚠️
THE CHOKE MUST BE MADE OF *IRON POWDER* not *farrarite* and the inductance will be 300uH not 3000uH .
*Farrarite* =3000uH ❎
*Iron Powder* =300uH ✅

[@artemisapollo8419]

1 like for his effort on bending those wires around!!!

[@Electronic_For_You]

My fingers are Hurting a lot 🥴

[@Master_Risky]

mantap 👌🏻ungkal 😄

[@user-ko8ed1mf6r]

very good project to make inductor high current

[@Electronic_For_You]

Thanks

[@HypersonicGuy-kr2bp]

👍👍👍👍👍👍

[@MDAsif-jj5lu]

Very nice 👍👍👍

[@Electronic_For_You]

thanks

[@kalashnikov_47z]

Nice 👌🏻

[@Electronic_For_You]

Thank you! Cheers!

[@sanjidaakter1814]

😊😊😊

[@rishad100]

Nice video broo ☺️👍
Make an experimental video link
How much current flows in solt water and in regular water

[@Electronic_For_You]

Nice Idea 🤔
Thanks for the idea .. i will definitely try 👌🏻

[@rishad100]

@@Electronic_For_You 😁👍🔥🔥🔥🔥🔥🔥

[@Electronic_For_You]

😁

[@andribayu8666]

what is the formula for Minimum inductor in design 55v current 30A frequency 39kHz ??

[@Abdullah-vt7ct]

you just earned a sub, I am also making a inductor for my sepic, 20A rms, 25 kHz, If Iron powder is not available in my country, should I use farrite?

[@Electronic_For_You]

If you use a farrite core then the inductance will be 10 × higher . I made the same mistake using Green Cores . Which i got 10 × the inductance of what it should. I got 1000uH instead of 100uh . So i strongly recommend using an iron powder core . From the computer power supply . If you don't have a store to buy

[@Electronic_For_You]

And
Thanks for subscribing
:-)

[@Abdullah-vt7ct]

You deserve it bro♥️..thank you for your suggestion, I actually need to make a 8.45mH, so the number of turns will be much less in farrite core, but I have heard that iron powder works best at this frequency range, that is why I was confused.

[@Electronic_For_You]

Maybe you are doing something wrong!
8.45mH is huge inductance
8450uH
I think You need like 100uH inductance for the 25-50khz range . 8mH will reach saturation. Then it will drow continuous current and blow up everything.

[@alfatihid8901]

how do you calculation,..??

[@Electronic_For_You]

What?

[@leopoldofernandezjr.508]

Name of inductor tester pls?

[@Electronic_For_You]

Multi Transistor Tester

[@SNIPER-69K]

What its for?

[@Electronic_For_You]

For boost Converter

[@SNIPER-69K]

​@@Electronic_For_You
Ok

[@JacquesMartini]

Ok, let's do the calculation for inductor #1
Specific inductance
18 turns, 2.6mH, Al = L/N^2 = 2.6e-3H / 18^2 = 8uH/N^2
ur ~ 12,000!
This is a high permeability core with no air gap, probably ferrite.
No air gap, very low saturation current
Magnetic cross section
Ae = (Da-Di)/2*h = (31-18)/2*6 = 39mm^2 = 39e-6m^2
average magnetic path length
le = (Da+Di)/2*Pi = (31+18)/2*Pi = 77mm
relative permeability
ur = L * le / (N^2 * A * u0) = 2.6mH * 77e-3m / (18^2 * 39e-6m^2 * 1.257e-6) = 12,600
Saturation current
Is = Bmax * N * Ae / L = 0.3T * 18 * 39e-6m^2 / 2.6e-3H = 81mA
"Slightly" below 30A . . .

[@Electronic_For_You]

Thanks

[@sergeypetrov1358]

😂