Great video, helped me install Bosch3000. One question though, you suggest connecting piezo siren to No and Aux, whereas Bosch Quick Ref Guide p.54 wiring diagram says to connect piezo siren to No and Ground. Pls clarify which is correct.
Thanks for sharing this video. By watching your video I was able to replace my fried board of solution 880 with a replacement solution 880 board. I have tested it working with the battery but I could not figure out how to connect the adaptor to the connector as my old cable colours were yellow/green, yellow & yellow. The new adaptor that came with the board has yellow/green, red & white. I can't attach the photo here to the comment but assuming you understand what I am asking for. I do not want to connect the wrong cable and kill the board. Any chance you can help & guide me on which cable goes where? I
No you don't. You can program unused zones as a "Not Used" zone type, and they will be ignored and not visible on the system. Check out our video on Zone Types for more info.
Hi there, thanks for sharing this video. I am installing Bosch 3000 alarm system for first time and was searching some informative videos for wiring up the system from scratch. I want to wire up 6 sensors. My board is same as your upgraded board. I have one strobe light, one hat siren one IP module and 6 sensors. Can you please show or send some pictures of wiring up this system and how to program it ? I would be very helpful for me. Waiting for your reply. Thank You
I've sent through a email for this too. I've also seen you have great prices. I'm looking to also install a 3g module any information on this would be great too. Do you need the b450 unit
The tamper switch connection is in the top right hand corner of the main board. If you don't want to use the tamper switch, just short out the terminals with a small piece of wire or go to menu "System -> Faults -> 8 "Onboard tamper triggers alarm" and turn that off on the text keypads, or Location 0495 = 2 on the icon keypad.
@@CheapAlarmParts Hi, great video, it helped me install the system. But how do you wire the strobe. I cant figure out how to install the LED and the Tamper. can you please help? Thanks in advance.
@@joelchan2403 if you have a horn siren wire the tamper in series and turn on horn monitoring. I use black fir strobe neg, red strobe pos, white fir horn pos , blue for horn neg(output 1).
Hi there,i noticed that you are not earthing the system.Can we do that?And also my cables are blue and white instead of green and yellow.please advise,thanks so much
I think using the grounding mount on the actual metalwork depends on the electrical regulations and telecommunications regulations in your country / state / territory - and if it's connected to a analogue phone line or not. To tell you the truth, I'm not sure. The max voltage in the unit is 18-20vAC from the plug pack, so none of it is 240v. The plug pack does have an earth which connects to the PCB. The earth is usually green and yellow. The other two cables don't have polarity so it doesn't matter which way around you connect it.
Cheap Alarm Parts Thankyou so much. Your. Very very helpful and you have made me extremely happy. I’m going to call up on Monday and order a lot of parts we need. Thankyou again.
Nice hints and tips even for those installing a panel from scratch I.e. loops in wires for identification.
Hi. Great video. Can you please provide the link to part 2? Thank you.
Good job you just made my task a whole lot easier, thanks for posting the vid.
Where is part 2? Seriously interested in purchasing one of these but lack of information is preventing me
Hi, I like this video and I’m going to try and swap my old Solutions 880 to 3000. Fingers crossed it’s as easy as it looks.
Your videos saved my life
We also do CPR at affordable prices!
Thanks for sharing this video but we couldn't find the part 2
Please make a video on how to install and mount the B426-m in the 3000 system
Great video but you didn’t explain where the external siren/strobe tamper cables go in the board. Also would be nice to add the board push tamper too.
Hi Guys Great video Thank you , Will the 2 ch Bosch RX remote panel EDM345F2 work with the 2000 series panel
Great job boss
Great video and very informative!
Great video, helped me install Bosch3000. One question though, you suggest connecting piezo siren to No and Aux, whereas Bosch Quick Ref Guide p.54 wiring diagram says to connect piezo siren to No and Ground. Pls clarify which is correct.
Either. The jumper setting makes the difference.
Glad I found this! My DIY go to!
Please should have mention the codepad will need changing too.
Hello, are you guys ok? Hopefully you can make part 2..
Very infomative video, but did I miss that siren and horn + go to AUX, horn - goes to output 1, but no telling or shown where the siren - goes?
Thanks for sharing this video. By watching your video I was able to replace my fried board of solution 880 with a replacement solution 880 board. I have tested it working with the battery but I could not figure out how to connect the adaptor to the connector as my old cable colours were yellow/green, yellow & yellow. The new adaptor that came with the board has yellow/green, red & white. I can't attach the photo here to the comment but assuming you understand what I am asking for. I do not want to connect the wrong cable and kill the board. Any chance you can help & guide me on which cable goes where? I
Thanks heaps, do you need to zone out 5-8 using resistors.
No you don't. You can program unused zones as a "Not Used" zone type, and they will be ignored and not visible on the system. Check out our video on Zone Types for more info.
Thanks for video,For external siren you have only wired 3 cables,i could not see a yellow cable nowhere ,is it not needed?Thanks
Hi there, thanks for sharing this video. I am installing Bosch 3000 alarm system for first time and was searching some informative videos for wiring up the system from scratch. I want to wire up 6 sensors. My board is same as your upgraded board. I have one strobe light, one hat siren one IP module and 6 sensors. Can you please show or send some pictures of wiring up this system and how to program it ? I would be very helpful for me. Waiting for your reply. Thank You
Hi. If you jump on to our website and go to the contact us page, I'll be happy to send you a cheat sheet which covers all of those connections.
I've sent through a email for this too. I've also seen you have great prices. I'm looking to also install a 3g module any information on this would be great too. Do you need the b450 unit
I second that
Do you know if it is possible to add a B426-M module to an ICP-CC488-SUB board? If not I might be following your instructions here...
nice video, can other brand of PIR sensors connected to Bosch system? will they have any compatible issues?
Yes, you can add other makes of hardwired sensors, as long as they are 12v and normally closed (NC).
I wired mine up as per this video, my siren and keypad are going off, everything lit up on keypad but not responsive.
Any reason this could happen?
Where is the tamper switch connection, and if you do not want a tamper switch how do you overcome that
The tamper switch connection is in the top right hand corner of the main board. If you don't want to use the tamper switch, just short out the terminals with a small piece of wire or go to menu "System -> Faults -> 8 "Onboard tamper triggers alarm" and turn that off on the text keypads, or Location 0495 = 2 on the icon keypad.
@@CheapAlarmParts Thank you very much
@@CheapAlarmParts Hi, great video, it helped me install the system. But how do you wire the strobe. I cant figure out how to install the LED and the Tamper. can you please help? Thanks in advance.
@@joelchan2403 if you have a horn siren wire the tamper in series and turn on horn monitoring. I use black fir strobe neg, red strobe pos, white fir horn pos , blue for horn neg(output 1).
Fantastic
Hi there,i noticed that you are not earthing the system.Can we do that?And also my cables are blue and white instead of green and yellow.please advise,thanks so much
I think using the grounding mount on the actual metalwork depends on the electrical regulations and telecommunications regulations in your country / state / territory - and if it's connected to a analogue phone line or not. To tell you the truth, I'm not sure. The max voltage in the unit is 18-20vAC from the plug pack, so none of it is 240v. The plug pack does have an earth which connects to the PCB. The earth is usually green and yellow. The other two cables don't have polarity so it doesn't matter which way around you connect it.
Brilliant
Does that have a built in receiver
Hi Frank. No you need to add a seperate receiver. The B810 for the Solution 3000; WE800EV2 for the Solution 2000.
Cheap Alarm Parts Thankyou so much. Your. Very very helpful and you have made me extremely happy. I’m going to call up on Monday and order a lot of parts we need. Thankyou again.