I ordered a PTO Cable and it came with only one spring. My PTO Cable came with 2 springs like the one in your video. The new PTO Cable stated it replaces the old one, but the new one doesn’t work or have enough tension. Thanks for any advice. I have the same riding lawnmower.
Ya know by the time Doria married Thomas Markle his 2 kids were teenagers and gone with their mom. However, they had visits with their dad and were very much in Meghan's life. That drama with her dad and half siblings is Meghan's fault for not having a good set down with all 3 of them and explained how things were going to be once her and Harry got engaged. Basically she just shunned them because she felt better than them. Shame on her for that. Integrity isn't about money.
Does the blade idler arm supposed to sit down in between that other piece of metal sticking up or is it supposed to move to the side when the blade handle is moved/engaged?
I just put a new blade on (used a 1/2 impact so I know it’s tight) and I’m sure it wasn’t in the exact spot on the star as the old one. Now I noticed (it could have been there before) a fluttering noise when the blade is engaged. It cuts great but I’m wondering if it’s a belt or bearing/pully issue, or if that noise is normal. The mower is about two years old, stored in a shed and only mows a 1/2 acre lot. Thoughts? And is there any PM that can be performed on the bearings?
I have a craftsman r1000. The issue I'm having is it will not shift and only goes slow. I looked at the shifter on the right side of the steering column and linkage. Still can't figure out why it will not shift to a higher speed. Can anyone help me, please?
The video is helpful but what if the belt is broken and not routed properly, can you show us how to fix our mower when the belt is gone or completely shredded? I have issues that your video didn’t help me with. Like the black lever you say goes up in the frame, mine has a spring and I see the spring on the one you’re working on, my spring isn’t connected to anything and luckily I see yours is mounted under the arm so I’ll see if I can mount mine like I see in this video, but that lever is connected to a pulley and that is also connected to a black piece of metal that has a rubber guide that rides inside the pulley for the blade, when I route the new belt like I see you do in the video the belt contacts that guide and it damaged my new bell I installed myself without seeing any video of on you tube. I fix cars so I figure I can replace a mowers belt, but I didn’t see that guide and didn’t know it was shredding my new belt until it shredded it. I’m getting my new belt today from Amazon so hopefully I’ll be cutting grass again soon. But I sure wish the video would show what to do if the belts failed, not a preventive maintenance video.
Okay my belt just arrived and I installed it no problem and yes this video helped out greatly. I think my mistake on the first install was not making sure the spring the goes under black lever of the tensioner was installed correctly and it caused the tensioner pulley to be in a downward position and by that happening the belt was twisted and getting shredded. Thanks for the video. Now I need one that shows how to adjust the carburetor if there is any adjustments available.
yes 3 bolt belt cover then one moore 10mm bolt belt tenion sleet! that all need take off!!!yes!!!! correct!!! i do mine same way! n 10mm bolt! 4 bolt all need take off mine2015tb30r!
I just want to say THANK YOU!! My belt was shot ran across this, watched a couple of times and I was able to change my belt just by looking at this video.. Great clear instructions...Will be subscribing.. Again Awesome job and thank you!!!
does this mower have just a deck belt or is there another belt? I only see what appears to be the deck belt but manual says there are 2 or 3 belts?? thanks for any feedback
The video has great detail except in the beginning should show us how to remove the pen and the cable removed from the bracket. The whole video did help me. Thank you so much Schultz II
Hi I purchased a used Craftsman 2012 RER1000 and my belt idler assembly looks different. It looks like I have to drop the pulley to get the belt out and that assembly is just floppy there is no spring tension and the bar you show with the black end is not attached 6:42 . Where can I find a parts list for this so I can purchase and get this installed correctly?
Thank you for this, I can not find anything on what I'm working on, it's a Toro 8-32 riding mower, model # 5614 replacement of belts, can you please help me 😢
Hi. My 30" craftsman won't go into reverse when I engage it. Do you know where the adjustment is? It's only about 3 months old, used less than 5x for about 30 minutes each time and doesn't have any obvious transmission noises so I'm guessing it's just an adjustment. I know the front engine craftsmans have a 2 bolt adjustment. thank you!
Either not going all the way in gear or has a chipped tooth on a gear. Check to make sure the idler pulleys for th drive system is good 5hey can make noise when going bad also.
I had to replace my lower drive belt on craftsman R110. The new belt came as a 35" instead of 35.25". Now it does not totally disengage when in netural. It tries to pull a little. HOW do I adjust this clutch issue? Thanks
Great video. I have a problem with the gear speed selector on my mower. After engaging the brake and releasing it the speed selector drops back to first gear all the time. Any suggestions? Thanks.
If you got man hands you gont have to remove the belt guide 🔩 for the idlers 😅 , good help tho . Very in depth , is there a tension for the belt , or is this ajusted with the height . Having slight vibration before and after deck service?
I was doing this the other day and a long spring popped off. It looks like it came off of the brake rod. I think it's the brake rod extension spring but I can't figure out where to put it back. Anyway you could help?
Have the same mower. Recently the thing has really lost power. I have replaced, upper trans belt, deck belt, fuel filter, air filter, cleaned the carb. New blade. Any insight on where my loss of power could be coming from? 6th gear feels like 2nd.
Great video!! Consider a 3M Ryman notched belt & HD dressing ( I know, but a little dab' lol do ya? Quiet, smooth & lasts & lasts. Since 1994 on my 90 , 2 belts & lathe center lube on the bearings & engagement! 😉😀 , Working on the CLU-BRAKE0 ADJUST " to keep the front wheels down & my teeth fillings in? Any idea's 🙏 you've tried? Updated fuel to filters, "T" connectors & a dump valve ( Amazon kit) braided line & I can dump that " moonshine fuel & water" stabill it & go another year? That $23.00 a gallon can gas is obscene ( purt pumps are 70 miles a way & my friend at the airport retired , so no 135 pure octane to mix for a while. ( Got some at EAA this year 4 next but then : BIDUMB corrosives? Yet still a good tube👍
Hello! Would you be able to help me, I removed the Bracket Asm Brake a few days ago to replace another part of my mower. Now I can’t figure out how to put the bracket asm brake back on ? For my craftsman R1000 mower
I broke and replaced the blade belt last year and it broke already. Wayched this video, saw what I did wrong and installed the new one in less time than before. Thanks for the help.
Hi! Really enjoyed this video, a HUGE Thank You! But am stuck, have a troybilt tbr30, my first belt fly off, am replacing it on garage floor. I do not have the strength to lift the back end, can only lower the deck to the lowest position. ANY suggestions please, from anyone out there, to get this new belt on the front pulley? Yep, a girl tacklin' it herself! Thank you in advance.
I still can't get the blade to engage. Where in the world does the Black on the Belt tightner go. I don't se a function for it but to pull down on the drive belt. Not very7 strong. I checked the PTO cable, iT IS TIGHT WHEN i LOCK IT DOWN. aNY HELO WOULD BE APPRICATED.
Thanks for this, It helped me see how I will be inspecting the belts and pulleys. My system stalls as soon as I lower the blade. Had a bent blade so I replaced it but it still stalls when lowering. I by-passed the switch with snap tie and the blade worked fine and the engine stayed on, it is only when utilizing the switch as intended, it stalls. I wonder why it is doing that?
I'm 40 and I have never owned a riding mower. I've done my fair share of work on vehicles but don't know the first thing about riding lawn mowers. This video is super helpful as I have the exact model of mower. I've got floor jacks for cars, a transmission jack, bottle jacks, etc, and several good tree stumps so hopefully I can get it in a safe spot for me to do this procedure. Next for me to learn is how to wash the deck....I see the hose fitting on it, lol. Thanks again.
Thank you so much for taking the time to make this comprehensive video repair. I always wondered how I might lift my mower to do this job myself and now I have a good idea. Very smart using a chain lift and lifting the rear of the mower where most of the weight is. How did you get it up on that work bench table?
Great video. Other videos have you take off the deck, not needed here. Also, you took off the belt cover and keeped it off to put the belt around the engine pulley FIRST , then around the blade pulley, putting the cover AFTER that. Other videos showed putting the belt around the blade pulley, putting on the belt cover, then struggling to put the belt around the engine pully. Your way gives way more space and room to do belt replacement quickly and easily. Thanks. As with other video creators that I learn useful stuff from, I'm sending a few $$ your way by using the "Thanks$" button above. I hope others will do as well to help you bring more useful content in the future. Peace out and God Bless.😎✌🖖🙏🤝
I have the same mower... I recently ran into the problem where the engine dies when I engage the blades. It deos die immediatly. It will slowly putter for minutes before it either revs up and gfoes or just sputters out and dies. Once it dies I cannot start it again. Usually it will take a day before I can get it to start and when it does white smoke goes out of the exhaust. Its not the safety switch as I already had that. Any idea what that might be? I would like to know where to start looking on my own.
my question is how can you raise/lower the cutting deck? Searches don't give me any help. My mower is set on the highest setting "level 5" but is still too close cutting, and setting 4 willl scalp and bog down the engine. I could use a 6 and 7 ! It seems the only adjustment is a hex nut facing forward to slightly raise the front of the deck. Any help out there?
I have a 30 inch R110/TB30 like in this video. My problem is the DRIVE BELT broke. I can't seem to find a video or detailed instructions on how to replace this belt. Any suggestions?
any way you could tell us how you jacked up the rear end to do this? I don't have a pulley or anything - just curious of a way to get it in the position you did for this video. great information btw- thanks for sharing.
Nice video. I got the same mower. My problem is with the brake for the blade. It doesn't move. Could use your experience and knowledge. The handle does not have any resistance when I engage the blade.
I have a Troy riding mower. I left it sitting for two years brand new or you all work and no return over but won’t start someone say I need to dump all the gas out and clean the carburetor. I don’t know can you help me
Thanks for the help! Got my mower fixed. Question for you. I had to add a manual valve to my gas line going to the carburetor. Is there a better was to prevent the gas from getting into the oil when the mower is just sitting? The valve works fine, just seems weird I had to add something that wasn’t from the manufacturer.
Your carburetor needs replaced its leaking from the needle seat. Fuel valve is a bandaid for the actual problem but will work if you remember to turn it off every time.
That bolt that you called a "belt guide," I've lost it and can't find it for purchase anywhere using that description of "bolt guide." Any ideas to help me with the search? Thanks!
I have one of theses and the drive belt broke. I was told that it is a real pain to replace and that it was not worth repairing. So just how do you replace one ?
Hey man, great vid. Subbed. Can you PLEASE help me, that little tensioner bar with the black like plastic end on it, the bar that is attached to the idler pulley, that somehow sheered off in half and I can't find the part anywhere or exact name of it. It's the chrome bar like 6 inches approx long with a 2 to 3 inch like black plastic/hard rubber end with 1 screw and thr very end of it bends in and sticks into the idler bracket, the black end sits against the mower I think. You know what I'm talking about I'm sure. I have to get this mower working asap, thanks a ton man!
@@D-MAN107 will do. Prob needs the whole idler pulley assembly I'm guessing and not just thr bar. I can post a pic of the broken part on your social media if that helps too
Thank you all for the awesome support I hope this video helps someone out👍🔧
What is the size of the belt?
What size belt is that ???
That's the belt for the blades. What about the drive belts?
I have 30 in troy bilt riding mower looks like air line above carburetor came off cant find were one end goes
What is the part number of the new belt you installed? The parts websites are giving me different numbers. Thank you
Thanks, this was the best video online. I was able to successfully change the drive belt and my mower is running like new!
Glad it helped
I ordered a PTO Cable and it came with only one spring. My PTO Cable came with 2 springs like the one in your video. The new PTO Cable stated it replaces the old one, but the new one doesn’t work or have enough tension. Thanks for any advice. I have the same riding lawnmower.
Belt is wrong or cable is wrong.
Great informative video, I’d love to see one on the drive also looks a bit more complicated.
Noted!
What is the size of the belt ?? Part #??
What’s that belt size. Online it says 43.5 x .5 but it’s to big
Ya know by the time Doria married Thomas Markle his 2 kids were teenagers and gone with their mom. However, they had visits with their dad and were very much in Meghan's life.
That drama with her dad and half siblings is Meghan's fault for not having a good set down with all 3 of them and explained how things were going to be once her and Harry got engaged. Basically she just shunned them because she felt better than them. Shame on her for that. Integrity isn't about money.
Does the blade idler arm supposed to sit down in between that other piece of metal sticking up or is it supposed to move to the side when the blade handle is moved/engaged?
What is the lenght or part number of the new belt? Looking on the internet it seems to be a mystery. Thanks
What size is the belt
its a 954-05001 belt
43.5x 1/2
30" I think.
Do you have the model number of the belt. I thought i did but the belt came too small. I have the r1000 as well and need roo chasms this exact belt.
craftsman2 ride-n-mulch 30' cut need the drive belt size
I just put a new blade on (used a 1/2 impact so I know it’s tight) and I’m sure it wasn’t in the exact spot on the star as the old one. Now I noticed (it could have been there before) a fluttering noise when the blade is engaged. It cuts great but I’m wondering if it’s a belt or bearing/pully issue, or if that noise is normal. The mower is about two years old, stored in a shed and only mows a 1/2 acre lot. Thoughts? And is there any PM that can be performed on the bearings?
Perhaps the idler pulley, or spindle bearings.
Hi, I have the Craftsmam version of this mower, r1000, what is the correct socket size and direction of thread for the blade. Thank you.
15/16 socket regular threads lefty loose
I have a craftsman r1000.
The issue I'm having is it will not shift and only goes slow.
I looked at the shifter on the right side of the steering column and linkage. Still can't figure out why it will not shift to a higher speed.
Can anyone help me, please?
Probably has worn out drive belts
The video is helpful but what if the belt is broken and not routed properly, can you show us how to fix our mower when the belt is gone or completely shredded? I have issues that your video didn’t help me with. Like the black lever you say goes up in the frame, mine has a spring and I see the spring on the one you’re working on, my spring isn’t connected to anything and luckily I see yours is mounted under the arm so I’ll see if I can mount mine like I see in this video, but that lever is connected to a pulley and that is also connected to a black piece of metal that has a rubber guide that rides inside the pulley for the blade, when I route the new belt like I see you do in the video the belt contacts that guide and it damaged my new bell I installed myself without seeing any video of on you tube. I fix cars so I figure I can replace a mowers belt, but I didn’t see that guide and didn’t know it was shredding my new belt until it shredded it.
I’m getting my new belt today from Amazon so hopefully I’ll be cutting grass again soon.
But I sure wish the video would show what to do if the belts failed, not a preventive maintenance video.
Okay my belt just arrived and I installed it no problem and yes this video helped out greatly. I think my mistake on the first install was not making sure the spring the goes under black lever of the tensioner was installed correctly and it caused the tensioner pulley to be in a downward position and by that happening the belt was twisted and getting shredded.
Thanks for the video. Now I need one that shows how to adjust the carburetor if there is any adjustments available.
yes 3 bolt belt cover then one moore 10mm bolt belt tenion sleet! that all need take off!!!yes!!!! correct!!! i do mine same way! n 10mm bolt! 4 bolt all need take off mine2015tb30r!
Right on
I just want to say THANK YOU!!
My belt was shot ran across this, watched a couple of times and I was able to change my belt just by looking at this video.. Great clear instructions...Will be subscribing.. Again Awesome job and thank you!!!
Thanks
does this mower have just a deck belt or is there another belt? I only see what appears to be the deck belt but manual says there are 2 or 3 belts?? thanks for any feedback
It has a drive belt for transmission also
The video has great detail except in the beginning should show us how to remove the pen and the cable removed from the bracket. The whole video did help me. Thank you so much
Schultz II
Noted
Hi I purchased a used Craftsman 2012 RER1000 and my belt idler assembly looks different. It looks like I have to drop the pulley to get the belt out and that assembly is just floppy there is no spring tension and the bar you show with the black end is not attached 6:42 . Where can I find a parts list for this so I can purchase and get this installed correctly?
Partstree.com has good diagrams
Thanks it looks like I need a missing spring on mine no bar. So once I get the spring then I need to figure out what it attaches to.
Saved me thNks brodie
What size is the belt
1/2 in x 43.5 in
If possible could you show how to adjust Brake/Clutch pedal so it will lock in place.Mine wi8ll catch a little and then pop up.. Thank, Dick W.
What would cause the blade on a trobuilt tb30r to not disengage?
Belt to tight wrong belt or cable is rusted or linkage is getting stuck.
Belt size?
What is a broken spindle mount? Where is it exactly?
It holds the blade and mounts to the deck
Thank you for this, I can not find anything on what I'm working on, it's a Toro 8-32 riding mower, model # 5614 replacement of belts, can you please help me 😢
Hi. My 30" craftsman won't go into reverse when I engage it. Do you know where the adjustment is? It's only about 3 months old, used less than 5x for about 30 minutes each time and doesn't have any obvious transmission noises so I'm guessing it's just an adjustment. I know the front engine craftsmans have a 2 bolt adjustment. thank you!
Transmission is clickying when put gear
Either not going all the way in gear or has a chipped tooth on a gear. Check to make sure the idler pulleys for th drive system is good 5hey can make noise when going bad also.
How do I adjust the clutch on this 30 “ lawn tractor
Not really any adjustments it's all in the belt. If belt is worn needs replaced.
I had to replace my lower drive belt on craftsman R110. The new belt came as a 35" instead of 35.25". Now it does not totally disengage when in netural. It tries to pull a little. HOW do I adjust this clutch issue? Thanks
Great video. I have a problem with the gear speed selector on my mower. After engaging the brake and releasing it the speed selector drops back to first gear all the time. Any suggestions? Thanks.
Probably has a worn selector
If you got man hands you gont have to remove the belt guide 🔩 for the idlers 😅 , good help tho . Very in depth , is there a tension for the belt , or is this ajusted with the height . Having slight vibration before and after deck service?
I can't get my deck to engage could the belt be stretched
It's either off a pulley or could have broken cable
I bought mine at a garage sale what is the part number for the belt and what's the part number for the blade on The rer 1000 30 inch deck mower
I got the pin off, but my deck won't drop. I can't pull it towards me enough to get it over the "arm" it rests on. ??
I was doing this the other day and a long spring popped off. It looks like it came off of the brake rod. I think it's the brake rod extension spring but I can't figure out where to put it back. Anyway you could help?
Have the same mower. Recently the thing has really lost power. I have replaced, upper trans belt, deck belt, fuel filter, air filter, cleaned the carb. New blade. Any insight on where my loss of power could be coming from? 6th gear feels like 2nd.
Great video!! Consider a 3M Ryman notched belt & HD dressing ( I know, but a little dab' lol do ya? Quiet, smooth & lasts & lasts. Since 1994 on my 90 , 2 belts & lathe center lube on the bearings & engagement! 😉😀 , Working on the CLU-BRAKE0 ADJUST " to keep the front wheels down & my teeth fillings in? Any idea's 🙏 you've tried? Updated fuel to filters, "T" connectors & a dump valve ( Amazon kit) braided line & I can dump that " moonshine fuel & water" stabill it & go another year? That $23.00 a gallon can gas is obscene ( purt pumps are 70 miles a way & my friend at the airport retired , so no 135 pure octane to mix for a while. ( Got some at EAA this year 4 next but then : BIDUMB corrosives?
Yet still a good tube👍
Hello! Would you be able to help me, I removed the Bracket Asm Brake a few days ago to replace another part of my mower. Now I can’t figure out how to put the bracket asm brake back on ? For my craftsman R1000 mower
After putting the new belt on, my blades never disengage. What’s wrong?
I broke and replaced the blade belt last year and it broke already. Wayched this video, saw what I did wrong and installed the new one in less time than before. Thanks for the help.
Glad it helped
Hi! Really enjoyed this video, a HUGE Thank You! But am stuck, have a troybilt tbr30, my first belt fly off, am replacing it on garage floor. I do not have the strength to lift the back end, can only lower the deck to the lowest position. ANY suggestions please, from anyone out there, to get this new belt on the front pulley? Yep, a girl tacklin' it herself! Thank you in advance.
Good luck! It can be done on the floor like your trying.
What size belt is used for this?
1/2" by 43" for the 30" deck models
I still can't get the blade to engage. Where in the world does the Black on the Belt tightner go. I don't se a function for it but to pull down on the drive belt. Not very7 strong. I checked the PTO cable, iT IS TIGHT WHEN i LOCK IT DOWN. aNY HELO WOULD BE APPRICATED.
Not sure what "black" your referring to?
My tr30r won't go forward or backwards it happened 2 weeks ago any suggestions or help would be appreciated...thank you!
Drive belt is off or broken most likely
Thanks for this, It helped me see how I will be inspecting the belts and pulleys. My system stalls as soon as I lower the blade. Had a bent blade so I replaced it but it still stalls when lowering. I by-passed the switch with snap tie and the blade worked fine and the engine stayed on, it is only when utilizing the switch as intended, it stalls. I wonder why it is doing that?
Glad it helped
On the blade pulley does the belt go behind the break
can u make a video on how to replace a drive belt pls
Can't seem to get belt on 42 inch weedeater riding mower
I'm 40 and I have never owned a riding mower. I've done my fair share of work on vehicles but don't know the first thing about riding lawn mowers. This video is super helpful as I have the exact model of mower. I've got floor jacks for cars, a transmission jack, bottle jacks, etc, and several good tree stumps so hopefully I can get it in a safe spot for me to do this procedure. Next for me to learn is how to wash the deck....I see the hose fitting on it, lol. Thanks again.
Right on
Thank you so much for taking the time to make this comprehensive video repair. I always wondered how I might lift my mower to do this job myself and now I have a good idea. Very smart using a chain lift and lifting the rear of the mower where most of the weight is. How did you get it up on that work bench table?
Glad to help
Great video. Other videos have you take off the deck, not needed here. Also, you took off the belt cover and keeped it off to put the belt around the engine pulley FIRST , then around the blade pulley, putting the cover AFTER that. Other videos showed putting the belt around the blade pulley, putting on the belt cover, then struggling to put the belt around the engine pully. Your way gives way more space and room to do belt replacement quickly and easily. Thanks. As with other video creators that I learn useful stuff from, I'm sending a few $$ your way by using the "Thanks$" button above. I hope others will do as well to help you bring more useful content in the future. Peace out and God Bless.😎✌🖖🙏🤝
Glad it helped
Awesome camera work and explanation
Thanks a lot!
What about removing the whole deck shell? That video would be 🔥
I have the same mower... I recently ran into the problem where the engine dies when I engage the blades. It deos die immediatly. It will slowly putter for minutes before it either revs up and gfoes or just sputters out and dies. Once it dies I cannot start it again. Usually it will take a day before I can get it to start and when it does white smoke goes out of the exhaust. Its not the safety switch as I already had that. Any idea what that might be? I would like to know where to start looking on my own.
Sounds like leaking fuel in the oil. Check oil see if smells like fuel.
Where can I find the transmission valve on a 30-inch riding mower
At 1:19 did I miss something? It seems like a step or two was skipped.
my question is how can you raise/lower the cutting deck? Searches don't give me any help. My mower is set on the highest setting "level 5" but is still too close cutting, and setting 4 willl scalp and bog down the engine. I could use a
6 and 7 ! It seems the only adjustment is a hex nut facing forward to slightly raise the front of the deck.
Any help out there?
Not much adjustment on these mowers they are built very cheap
I have a 30 inch R110/TB30 like in this video. My problem is the DRIVE BELT broke. I can't seem to find a video or detailed instructions on how to replace this belt. Any suggestions?
I will post one on the next job that comes in
any way you could tell us how you jacked up the rear end to do this? I don't have a pulley or anything - just curious of a way to get it in the position you did for this video. great information btw- thanks for sharing.
I use a electric winch hanging from my ceiling. But anything can work or even a engine picker
you took off extra just lower deck! dont need take deck off!!! lower allway down how i did mine tb30r 2015!!!
I’m sure he did it so we could clearly see what he was doing. For video purposes only.
I need to replace the drive belt on mine….heard it is a real pain
It's not to bad but it's tight
Nice video. I got the same mower. My problem is with the brake for the blade. It doesn't move. Could use your experience and knowledge. The handle does not have any resistance when I engage the blade.
Thanks for sharing sounds like the cable is broken for the blade engagement.
riding LAWNMOWER RER1000 CRAFSMAN HIT STUMP CUTING UNEVEN NOW PLEASE ADVICED.
Probably has bent blade or broken spindle mount
I have a Troy riding mower. I left it sitting for two years brand new or you all work and no return over but won’t start someone say I need to dump all the gas out and clean the carburetor. I don’t know can you help me
Sounds like the carburetor needs cleaned and fuel system flushed.
How to remove the engine on a troy bult 30r in rear engine riding mower
Great vid. Only thing I would add is to put a dab of anti-seize compound on the belt keeper bolt threads.........
Yeh mine just came out and I can’t find a replacement 🤬
Thanks for the help! Got my mower fixed. Question for you. I had to add a manual valve to my gas line going to the carburetor. Is there a better was to prevent the gas from getting into the oil when the mower is just sitting? The valve works fine, just seems weird I had to add something that wasn’t from the manufacturer.
Your carburetor needs replaced its leaking from the needle seat. Fuel valve is a bandaid for the actual problem but will work if you remember to turn it off every time.
I have an MTD 30" rear engine mower. how does the forward reverse shifter knob come off?
Pulls of or twist
Great video, My gf son in law has one of these mowers, he broke the handle by the pully on the left side, what is that handle for?
Helps keep the idler pulley in line
I'm trying to replace the drive belts on the tb30r Troy Bilt riding mower. Do you have a video?
Not currently but I'm sure we will
My belt keeps coming off, would replacing it fix the issue? Thx
Possible but may have other issues
I replaced this belt on my craftsman R1000, but the belt is still loose.
Should only be tight when engaged
That bolt that you called a "belt guide," I've lost it and can't find it for purchase anywhere using that description of "bolt guide." Any ideas to help me with the search? Thanks!
Lawn mower shop can order one. If not contact us.
@@D-MAN107 alright, thank you
I have one of theses and the drive belt broke. I was told that it is a real pain to replace and that it was not worth repairing. So just how do you replace one ?
It's not that bad really.
Thank you,, Would like to see a vid on replacing or servicing the blade spindle.
Noted!
How do you get spring back on?
What size belt?
selffish ass dude not disclosing the full info
Hey man, great vid. Subbed. Can you PLEASE help me, that little tensioner bar with the black like plastic end on it, the bar that is attached to the idler pulley, that somehow sheered off in half and I can't find the part anywhere or exact name of it. It's the chrome bar like 6 inches approx long with a 2 to 3 inch like black plastic/hard rubber end with 1 screw and thr very end of it bends in and sticks into the idler bracket, the black end sits against the mower I think. You know what I'm talking about I'm sure. I have to get this mower working asap, thanks a ton man!
We can order one just call us at winderoutdoorpower
@@D-MAN107 will do. Prob needs the whole idler pulley assembly I'm guessing and not just thr bar. I can post a pic of the broken part on your social media if that helps too
I have the same mower and it won’t move back or forth. What do you think is causing this?
Drive belt or brake stuck
Need help with drive belt
Great video! Helped me out with a snapped idler rod on my mower. I wasn't sure how it was supposed to be installed and this was perfect.
Glad it helped!
Need photo of where idler rod really goes please, it is obstructed in this video.
Thanks for the video please yo a drive belt one because that seems to be a lot trickier including as best as I can tell removeimg the deck belt first.
Great suggestion!
Watch the torque on the 30 on the blades
what size belt craftsman R 1000
Man i had to replace all the belts on mone about a year ago, i learned as i went wish i had this vid!
when I engage my blades the engine dies. I suspect the drive belts. please do a video on this
Did you figure out what the problem was?
how do you adjust the height of the mower blades , mine are too low, is there an adjusting screw ? Great Vid !!
I that mower there is not much adjustment unfortunately.
Very good instructions. How many belts does that particular mower have and type?
Thanks, just a deck belt and drive belt.
Great video it was very helpful! Thank you!
Thanks
Great Video. Do you have parts or brand name number for the belts you used?
Yes
I’ll finished
6/9/23 this can also be done on the floor. If one is carefull
Definitely
Gracias hombre🤜🤛