All Terrain Ride on Mower - BUILD

Поділитися
Вставка
  • Опубліковано 24 гру 2024

КОМЕНТАРІ • 515

  • @MadeinPolandChannel
    @MadeinPolandChannel  2 місяці тому +82

    Longer and more advanced test in the next video :D
    Some things used in the video:
    amzn.to/482MKlK - Evolution S355MCS 14" Mitering Chop Saw
    amzn.to/3zSiwp7 - EVOMAG42 Magnetic Drilling
    amzn.to/3U951Ip - Gear Rack Pinion

    • @stalbertjocelyn
      @stalbertjocelyn 2 місяці тому +7

      it looks like your PTO clutch was installed with the disc installed over the break tab. when you activate the clutch it looks like its binding.

    • @Nobe_Oddy
      @Nobe_Oddy 2 місяці тому +4

      Isn't that an AIR COOLED engine? ... but it's not gonna get ANY AIR.... and the rear end/transmission getting air from the engine.. it's gonna be REALLY HOT AIR because the engine WILL run HOT.....
      - if it does run too hot, maybe you could put a FAN behind the seat (like the fan from a car radiator, that runs on an electric motor) and use some sheet metal to not separate it from the back of the seat AND channel the air to be drawn in from both side of the seat... and you might be able to channel some of the fan exhaust under the engine to the transmission.. 🤷‍♂
      - - I'm only halfway into the video, where you mounted the gas tank with that big thick sheets that WILL channel all that heat RIGHT ONTO THE BOTTOM OF THE GAS TANK.... SO IDK if you changed anything, or kept the design like this... I'm not a mechanic, or an engineer, but I would think that the heat of the engine is gonna get trapped from those sheets and the gas tank, ESPECIALLY when it's not moving AND because it's probably not going to be moving very fast... but I could be totally wrong of course :/

    • @Nobe_Oddy
      @Nobe_Oddy 2 місяці тому +4

      You should REALLY sharpen the WHOLE LENGTH of you blade.... it's like trying to chop down a tree with a baseball bat instead of an axe.... you don't have to sharpen both side like you did with those tip pieces (which think could end up flying off after a while from the vibrations shaking the bolts enough to become loose, but PROBABLY NOT) but you NEED TO cut grass with a SHARP BLADE..... But if you SHARPEN BOTH SIDES of the blade, then you can just FLIP IT OVER when one side gets dull LOL ..... but you REALLY ought to make it into a proper blade :)

    • @dandahermitseals5582
      @dandahermitseals5582 2 місяці тому

      That's gonna weigh a ton.😮😅

    • @dandahermitseals5582
      @dandahermitseals5582 2 місяці тому +1

      Me too

  • @abdwahid7923
    @abdwahid7923 2 місяці тому +10

    I'm from Malaysia, I've been watching a lot of fabricating works that related to engines, body works on cars/trucks but I've never seen such a professional modification on mowing machine. Keep it up bro. Awesome.

  • @wrightcabin4132
    @wrightcabin4132 2 місяці тому +41

    Beautiful work my polish friend. I am a retired mechanic that worked on all aspects of mechanical equipment but I wish I had your skill set. You create extraordinary pieces of equipment.

  • @MikefromMOMichaelTurner227
    @MikefromMOMichaelTurner227 13 днів тому +2

    Retired machinist here, the thing that encourages me is,,, By building your own mower you have skipped all of the plastic and crappy design. I am encouraged!! Think that I might build one for me 😊 congrats on a job well done 👍

  • @gregmoser2086
    @gregmoser2086 27 днів тому +3

    This dude just like "meh, I need a mower. I'mma make a mower. AND film it!" Keep on creating my friend you do amazing work.

  • @danielrichardson1210
    @danielrichardson1210 Місяць тому +1

    Love the "stitched" plasma lines to fold it easier! I think the shoulder in the center of the wheel hub to enter the rim is fondamental to avoid shearing the studs and keeping the wheel centered at all times without vibrations

  • @maxatherelaxer
    @maxatherelaxer 2 місяці тому +4

    Looks fantastic. My only suggestion would be to weld 45degree plates along the underneath folded edges (internal 90 degree bends) of the blade shroud to minimise debri build up. Keep up the videos I love em and they inspire me to work in my shed on weekends also.

  • @CopperCreekCuts
    @CopperCreekCuts 2 місяці тому +17

    Looks a bit like an OREC. This Florida lawn guy approves!

  • @bigbaby1177
    @bigbaby1177 23 дні тому

    WOW I have watched your builds on and off for several years and this is the first time I have seen you speak. :)

  • @WinchesterWoodWorks
    @WinchesterWoodWorks 2 місяці тому +25

    Mad Max called, he want his mover back 🥰

  • @rickarndt3895
    @rickarndt3895 Місяць тому +1

    I'll tell you one thing that this cats got it going on if you want something built he's the man for the job.

  • @Atlantismonkey40
    @Atlantismonkey40 2 місяці тому +4

    When you’re making the next metal plate with many holes. Take a look at the guys installing tiles. They use a laser pointer. It’s a very simple way to get detailed marks. Well done, looks fun

  • @lorenzoghinelli7018
    @lorenzoghinelli7018 2 місяці тому +1

    Nuoooooooo pazzesco Belluz, quel trattore è rarissimo!!! Non per uso agricolo ma portato a qualche esposizione diventa il Re della manifestazione! Poter mettere le mani su un mezzo del genere è veramente un privilegio! Anche la famosa pompa Bosh la puoi far ripartire, hai bisogno “solo” di un buon tornitore e di una tenuta fatta su misura! Non vedo l’ora di vedere i prossimi video di questo meraviglioso progetto!

  • @MaacAbra
    @MaacAbra 2 місяці тому +1

    Jak zwykle masę solidnej roboty. My mieliśmy pod ręką Wladimirca, więc po prostu zbudowaliśmy do niego kosiarkę na bazie mostu od Mercedesa. I to przynajmniej jest zestaw prawie All terrain, ma konkretną szerokość i wjeżdża nawet w 1,5m chaszcze ;)

  • @kevinmoyle6098
    @kevinmoyle6098 23 дні тому

    Love your shop. The tools are you. And together with your skill set, you are one creative man. Nothing like having the satisfaction of creativity of making you own equipment. Nicely done sir.

  • @vojtahrabanek4185
    @vojtahrabanek4185 2 місяці тому +5

    Made in Poland - meet the masters of CAD: cardboard autonomous design 😂😂. Great build!

  • @kiniakinia1000
    @kiniakinia1000 2 місяці тому +13

    Idzie jakby oporu nie czuła. Bestia nie kosiarka. Lux robota.

  • @AraCarrano
    @AraCarrano 2 місяці тому +17

    Great work as always, Just needs foot controls so you can steer and hold a beer in the other hand.

    • @kirdot2011
      @kirdot2011 2 місяці тому +1

      i noticed that as well. it wouldnt even have the need for pedals if the speeds were fixed like in a standard Husqvarna mower, but here it seems like you have to keep the hand on the lever all the time

    • @Displacement-destroyer
      @Displacement-destroyer 2 місяці тому +1

      ​​I agree.He needs to put notches like he did for the deck height in that handheld speed controller 3 forward Like 2 For when not cutting grass in reversuch as slow and high speed😊

  • @grahamcifuentes4451
    @grahamcifuentes4451 2 місяці тому +2

    You should be proud of yourself! A couple of minor points. I can see that blade bar bending the first time you hit a half buried log or rock, and I think you will find the thing much easier to drive with the forward/ reverse control as a foot pedal, rather than a hand lever.

  • @marcliebich9166
    @marcliebich9166 2 місяці тому +1

    This guy is brilliant. First time seeing this. Wish i could learn from him. Bravo

  • @MultiKelly85
    @MultiKelly85 2 місяці тому +1

    First off let me apologize for seeming greedy. Your video and builds from ground up are phenomenal! I wish they can be done faster but these builds take time. AWESOME VIDEO!!! KEEP IT UP!!!

  • @LaidOffGarage
    @LaidOffGarage 26 днів тому

    The whole world collectively gasped when you broke that tap 😂 Excellent video !

  • @WACRE44
    @WACRE44 Місяць тому +1

    Thanks that’s brilliant ! Better than any thing here in this country 😢

  • @NWMT
    @NWMT 2 місяці тому

    Very nice! So glad to know there are no grass field rocks in Poland.

  • @vannewman4777
    @vannewman4777 2 місяці тому

    you never cease to amaze me with your skill and workmanship another quality job my fried I am so envious

  • @kevinfisher1632
    @kevinfisher1632 2 місяці тому

    Superb piece of kit you have made there, anyone would be glad to own anything that is made by you.

  • @krystianrugowski2935
    @krystianrugowski2935 2 місяці тому +4

    Jeden z najfajniejszych projektów 😊 pozdrawiam i czekam na kolejne projekty

  • @jayburrough4308
    @jayburrough4308 2 місяці тому

    I've been wanting to see someone do this and he did amazing

  • @StefanBlurr
    @StefanBlurr 2 місяці тому +5

    I love the exhaust system

  • @buggyland
    @buggyland 2 місяці тому +9

    Eats grass without a sweat. Looking forward to seeing how well the diffuser works on the high speed tests.

  • @sportytone1
    @sportytone1 29 днів тому +1

    Be sure that the "V" in the tread of the rear tires is pointed down when seen from behind, It is necessary for the self-clearing action of the tread can work. Ask a farmer. Tractors use the same tread pattern.

  • @johncarter9067
    @johncarter9067 2 місяці тому +1

    I couldn't do what you do but I love watching your videos

  • @jeremygreenwood8501
    @jeremygreenwood8501 2 місяці тому

    Fascinating. I wish I had half your skill and ingenuity.

  • @shawndubay4050
    @shawndubay4050 2 місяці тому

    Awesome mower. Sounds and looks great. Only things I would change are I would put on a high lift mower blade and a roll bar maybe a seat belt for uneven terrain. A roll bar can save your life my friend. I personally would have it two feet taller than the rider/ yourself. I call it the non crush zone.

  • @thaiexodus2916
    @thaiexodus2916 2 місяці тому +3

    Just for fun I did some number crunching. 36 inch blade needs at least 5 HP. 6 or 7 HP to move it at a decent speed. So it's right in the sweet spot allowing it to mow at travel speed without breathing hard.
    Now to test the brush crushing. Next video. No doubt you'll be needing to do some more welding and beefing a few things up.
    For a prototype, that's a submission of an engineering degree final exam. Design, fabrication, utility and execution all covered.
    PS I can't get enough of that pneumatic hands free vice. Talk about a time saving frustration eliminator. And the miter gauge on the brake is the cat's meow.

  • @pycoed
    @pycoed 2 місяці тому +13

    Very impressive as usual! Only thing I'd suggest is some 10mm bar to reinforce the edges of the mowing deck - it doesn't take much of an impact to bend 2mm plate into the blade arc...

  • @johngato737
    @johngato737 2 місяці тому

    I learned a new word today. Thanks for leavin in the good stuff. Love this build.

  • @jwfinley7808
    @jwfinley7808 28 днів тому +1

    Your going to get allot of grass pilling up on the bottom?

    • @jwfinley7808
      @jwfinley7808 28 днів тому +1

      allot of build up!

    • @jwfinley7808
      @jwfinley7808 28 днів тому

      Because your cutting is not smuth all way around.

    • @jwfinley7808
      @jwfinley7808 28 днів тому

      only cut dry or you'll run into problem's.

    • @jwfinley7808
      @jwfinley7808 28 днів тому

      Good job!

  • @CoolIdeasDIY-qv1nz
    @CoolIdeasDIY-qv1nz 2 місяці тому +1

    Great performance colleague😊😉🙂

  • @Nobe_Oddy
    @Nobe_Oddy 2 місяці тому +1

    What an EXCELLENT MOWER!!! WOW!! You really are an AMAZING BUILDER!!! You9 make me SO PROUD to be Part Polish!!! :D

  • @tony4metallicaify
    @tony4metallicaify Місяць тому

    Looks like a ole Snapper on steroids! Nice job!!!

  • @dawidiuszwspanialy
    @dawidiuszwspanialy 2 місяці тому +2

    Brawo ! Świetna robota ! Pozdrawiam z Niemiec !

  • @rafalkosciolekk
    @rafalkosciolekk 2 місяці тому +3

    Ale kozak traktorek
    Konstrukcja pancerna nie do ruszenia ale silnik ma co ciagnac ,no i ta srednica koszenia tez swoje robi 👍

    • @MadeinPolandChannel
      @MadeinPolandChannel  2 місяці тому +4

      Powiem Ci, że ten silnik w ogóle nie odczuł tej trawy. Zobaczymy w przyszłym filmie co będzie z krzakami, gałęziami, czy nawet małymi drzewkami :)

    • @rafalkosciolekk
      @rafalkosciolekk 2 місяці тому

      @@MadeinPolandChannel mój traktorek ma 15 koni i ramę lichą strasznie ,osłon trochę z cieniutkiej blachy i plastików a czuję że ma ciężko
      Tym większe brawa dla Ciebie

  • @MesRevesDe
    @MesRevesDe Місяць тому

    A mower with a karting Cross look 👍. Well done, it's very cool

  • @BCHonea
    @BCHonea 2 місяці тому

    No lathe, no milling machine yet you fabricated an amazing machine. Someone donate this man some machines

    • @jerryspence7484
      @jerryspence7484 2 місяці тому

      I was thinking a truck load of steel lol and some axles

    • @XerfThingol
      @XerfThingol 2 місяці тому +1

      He is using a lathe.

  • @rks9612
    @rks9612 2 місяці тому +6

    Do you work from some sort of plans or make stuff up as you go? I am more of the second type!

    • @MadeinPolandChannel
      @MadeinPolandChannel  2 місяці тому +12

      50/50 😁

    • @dimitar4y
      @dimitar4y 2 місяці тому +1

      things never work 100% to plan so.. he's shown in older videos his plan go to £$%^ so he makes plans, and a lot of finnicky stuff he "builds" in-place.

  • @DanKoning777
    @DanKoning777 2 місяці тому

    Not only is it able to cut grass and brush, but I wouldn't be surprised if it was just as fun and capable at a local drag strip, or a hill climb event. 😂
    Nicely done once again-great look/design also. I'd love to see you and "Workshop From Scratch" team up and do collaboration video. 👍

  • @MesRevesDe
    @MesRevesDe Місяць тому

    Hello. Fantastic work It's exciting to see someone work metal with such precision and love of a job well done It gives the feeling that everything is possible for those who know how to buy the right tools and use them. Well done and thank you for sharing. ❤

  • @Evilslayer73
    @Evilslayer73 2 місяці тому +1

    Its aliveeeeeeeeeeeeee!!!!!!!its alive!!!!!!!!!!!!!!!!!!! salutation from Montreal,Québec!!:)

  • @opendstudio7141
    @opendstudio7141 2 місяці тому +6

    That build looked expensive to make, but it appears you are able to make a good profit when sold.
    Excellent video and very entertaining to those of us who understand the complexity and appreciate this level of mechanical skill.

  • @mechanicalcenturyus
    @mechanicalcenturyus 2 місяці тому +2

    It's amazing, the machine works very efficiently!

  • @michelduthu2995
    @michelduthu2995 2 місяці тому

    Qu’elle maitrise chapeau l’artiste , tout ce que tu touches ce transforme en or 😮 ❤

  • @de04609
    @de04609 8 днів тому

    Love this guys c.a.d work!
    If you know, you know.

  • @Lorenzo.Giorgi
    @Lorenzo.Giorgi 2 місяці тому

    More a rocket than an all terrain! Quite cool

  • @bisket2003
    @bisket2003 2 місяці тому

    Just found this channel, but you make this look WAY to easy!! Hahah. Incredible skills man. Beautiful build. Super simple video and gets right to it! Many blessings sent from one Pollack here in the states!

  • @custos3249
    @custos3249 2 місяці тому +4

    Half expected you to retrofit a mower deck to an ATV chassis lol

  • @janwanrooij5365
    @janwanrooij5365 Місяць тому

    Cześć .
    Bardzo ładne spawanie w Twoim wykonaniu, też bym tak chciała.
    Ale nie widziałem, żebyś smarował obracające się części, takie jak mechanizm kierowniczy. Znowu podobał mi się Twój film.
    Pozdrowienia z Holandii

  • @garyjohnson9297
    @garyjohnson9297 2 місяці тому

    A very rugged build , a few suggestions? First, make two fillet plates and weld them in the inside angles on the front axle . Replace the front axle pivot bolt nut with a crown nut and cotter pin . Replace the doubled nuts with lock nuts . And make a full-length weld on both sides of the mower height adjustment selector plate

  • @geraldsundberg3610
    @geraldsundberg3610 2 місяці тому +1

    A nice looking build and a fun project!

  • @vinceianni4026
    @vinceianni4026 2 місяці тому +1

    Good job mister beautifully done

  • @3beltwesty
    @3beltwesty 2 місяці тому

    That is a nice build..it looks roughly the size of my 1985 Toro 11 32 mower

  • @adammickiewicz4093
    @adammickiewicz4093 2 місяці тому

    9:50: CAD - Cardboard Aided Design :D
    Świetnie się ogląda, jak zawsze!

  • @willmaxwell2184
    @willmaxwell2184 26 днів тому

    I would love to see a video of your shop setup, room size, various tools and such.

  • @stevepiechock9234
    @stevepiechock9234 2 місяці тому +1

    Absolutely incredible!

  • @Punkineddy
    @Punkineddy 2 місяці тому +1

    I compliment you on your work!!!

  • @marjukii-ze5vw
    @marjukii-ze5vw 2 місяці тому +1

    From Indonesia 🇾🇪, 👍👍👍....

  • @JamesCopeland-i1j
    @JamesCopeland-i1j 2 місяці тому +1

    45:15 - you'll want dual cables, or install rigid linkage to the speed control. When you're on a hill, the resistance will bind your single cable.

    • @MadeinPolandChannel
      @MadeinPolandChannel  2 місяці тому +1

      it's not a rope, but a steel wire that acts on the sheath and the pulling.

    • @JamesCopeland-i1j
      @JamesCopeland-i1j 2 місяці тому

      @@MadeinPolandChannel - I understand that... but it's still not designed to push with much resistance. I hope you get the longevity you want out of it. Doesn't look like you have many slopes to worry about anyway.

  • @jannie5724
    @jannie5724 2 місяці тому +18

    I to piękne Polskie zaklęcie w momencie gdy pękł gwintownik 😀 Bardzo fajna ta karczownica 👍

    • @zl3434
      @zl3434 2 місяці тому +3

      Slowo: "KURWA" tlumaczy wszystko doskonale ! :-)

  • @sashachubakov94
    @sashachubakov94 2 місяці тому +2

    ⚜️Kosiarka jest dobra, ale można ją było dodać do przedniego zawieszenia para amortyzatorów dla wygody. Dobra robota, dobra robota. Zbierz wypróbuj minitraktor wielkości hinomoto. A z tyłu zrób Frezy do pspashki .byłoby bardzo interesujące .czekam na ten filmik ⚜️

  • @Daniel-n5v5s
    @Daniel-n5v5s 2 місяці тому +1

    Looks like it did a good job 👍

  • @renripari5514
    @renripari5514 Місяць тому +1

    GREAT WORK 👍

  • @johnmcmccormack9203
    @johnmcmccormack9203 2 місяці тому

    Very well done, excellent workmanship. Thank you for sharing. Looking forward to seeing your next project.

  • @kevinstorm2167
    @kevinstorm2167 Місяць тому

    Very nice set up, I am envious of your shop!

  • @rickarndt3895
    @rickarndt3895 Місяць тому

    Some people have just got intelligent beyond measure. How about a double thumbs up.

  • @jonr473
    @jonr473 2 місяці тому

    An absolute beast well done 👍

  • @alevans51
    @alevans51 2 місяці тому

    There you go! Very impressive!

  • @mrdebug6581
    @mrdebug6581 2 місяці тому

    really? is there ANYTHING you can NOT do?
    beside rocket-science you used EVERY skill I know of
    🏅🏅🏅👏🏼

  • @gogigogi5470
    @gogigogi5470 2 місяці тому +1

    Наконец то дождались, есть что вечером посмотреть!

  • @ferg4618
    @ferg4618 2 місяці тому +1

    Very impressive, you are quite a talented fellow.👍

  • @chadsmith9218
    @chadsmith9218 Місяць тому

    15:45 was hard to watch and was surprised to see due to you being a superb fabricator

  • @Jarda_B
    @Jarda_B 2 місяці тому +1

    16:08 That was the most genuine KURWA I ever heard 🤣🤣 almost had me crying

  • @jeff11030
    @jeff11030 2 місяці тому

    You certainly are a master craftsman. I never see you refer to any plans during your project. Did you design this yourself or do you follow someone else’s plans? I’d bet you design it around the parts you have on hand, then get other parts as you need them. But you must sketch it up ahead of time to make sure all the engineering will work.
    Your designing and construction skills are top notch. You have my full respect.

  • @kravanamjesecu
    @kravanamjesecu 2 місяці тому

    Grillo Climber AWD copy,great work!!

  • @janmajitshankar447
    @janmajitshankar447 2 місяці тому

    What a build, bro. I enjoy watching your videos. The perfection you give to your invention is truly satisfying!❤

  • @deki2301fake
    @deki2301fake 2 місяці тому

    In April, I send you message on Instagram that you should build this kind of machine 🤣 I'm so happy you really made it 😅

  • @javilarg
    @javilarg 2 місяці тому

    An amazing project as usual

  • @alainblondelot9707
    @alainblondelot9707 2 місяці тому +1

    Bravo une très belle réalisation

  • @kestutismartinkaitis7586
    @kestutismartinkaitis7586 Місяць тому

    Puikus traktorius 👍👍👍
    Linkėjimai iš Lietuvos 🇱🇹

  • @stevekorup7366
    @stevekorup7366 2 місяці тому +1

    Very Cool Build, I enjoyed the entire Video. you got a new Subscriber from the USA. Keep up the great videos and Stay Safe over there. Look forward to watching more of Your builds.

  • @genesmay6589
    @genesmay6589 2 місяці тому +2

    I want this guy on my fall of civilization crew..

  • @bigchiefbear
    @bigchiefbear 2 місяці тому +2

    Awesome build.awsome video. Thanks for sharing your skills with us. 😊😊

  • @NaturalBBler
    @NaturalBBler 2 місяці тому +1

    you can convert the handheld accelerator to two food pedals. Right food forward and left food backwards

    • @user-neo71665
      @user-neo71665 2 місяці тому

      On bumpy ground they are a PITA. You get to bouncing you will be glad you can use your feet to brace yourself anywhere you can instead of trying to worry about foot pedals. Plus you don't have to worry about your foot getting tired holding something down over long periods.

  • @Energetyk321
    @Energetyk321 2 місяці тому +1

    Całkiem spoko, coś na zasadzie karczownic Orec. Ja osobiście używam traktorka Stiga Villa (kosisko z przodu, tylna oś skrętna, gaz i hamulec w pedałach) i wydaje mi się to najlepsza opcja... Mega manewrowe i nie ugniatasz tego co kosisz przednimi kołami. Oferowali fabryczne rozwiazania zamiast przedniego kosiska (kosiarka bijakowa, małe pługi do "orania", pług do odśnieżania, zamiatarka ). Myślę osobiście o dorobieniu glebogryzarki... Może zainspiruje Cię takimi pomysłami do kolejnego projektu :)

  • @gonzalo7130
    @gonzalo7130 15 днів тому

    Excelente !!!!
    Saludos desde Argentina 🇦🇷💪

  • @kymmarshall1116
    @kymmarshall1116 2 місяці тому +1

    That’s a great looking build 👍🏾🇦🇺

  • @przemysawfojcik1932
    @przemysawfojcik1932 2 місяці тому +3

    Fachowa robota, pozdrawiam.

  • @domelodi
    @domelodi 2 місяці тому +2

    Good work, clean workshop, I like that. What is the model od the transmision? Cheers Mate!

    • @MadeinPolandChannel
      @MadeinPolandChannel  2 місяці тому +3

      I don't know the name, but I got it from allen commander turf trooper 2 🙂

    • @domelodi
      @domelodi 2 місяці тому

      @@MadeinPolandChannel Thank you.

  • @KarapuzkinYouTuber
    @KarapuzkinYouTuber 2 місяці тому +12

    Красивая осень! Красивая работа! Классный аппарат!!! Вы хороший инженер!!!

  • @simonallan9941
    @simonallan9941 Місяць тому

    What a mean machine 🤗 awesome job bro

  • @varinotbruno1401
    @varinotbruno1401 Місяць тому

    Magnifique, travail de professionnel, très ingénieux 👍👍👍👍👍