Eibos Cyclopes + Eurus Review - Filament Dryer and Storage Solution

Today I'm reviewing the Eibos Cyclopes Filament Dryer and Eibos Eurus vacuum which should hopefully dry your filament, improve your print quality and keep it nice and dry during storage. Let's find out!
0:00 Intro
0:36 Eibos Cyclopes Specs, Cost to run
1:18 Why you need a filament dryer
2:14 Printing with dried vs undried filament
2:30 Pro's
5:32 Con's
11:25 Quality control issues
11:49 Eibos Cyclopes Conclusion
13:10 Eibos Eurus Review
3D Printed Roller Extensions - www.printables...
Eibos Cyclopes: aliexpi.com/IO0h
(US) amzn.to/3X9eIpY | (UK) amzn.to/3IIq1AN
Eibos Eurus: aliexpi.com/EBap
💚 Support me 💚
Patreon - / thisdesignedthat
3D printing moisture-laden Nylon
• 3D printing moisture-l...
---------
GEAR USED:
CAMERA (US) amzn.to/3pONh5M | (UK) amzn.to/3TfULfs
FAV LOW LIGHT LENS: (US) amzn.to/2QT7aJ5 | (UK) amzn.to/2v7HbRr
FAV MACRO LENS: (US) amzn.to/2VcOa6O | (UK) amzn.to/2V12pPA
GOOD VLOG MIC: (US) amzn.to/2Sdr12I | (UK) amzn.to/2DfVyHU
AMAZING LOW COST LIGHT: (US) amzn.to/2ElMJxg | (UK) amzn.to/2v8A23u
120CM QUICK SETUP SOFTBOX: (US) amzn.to/2IAOBDf | (UK) amzn.to/2F6jcrd

[@michaelculbertson7065]

Great review! It was very helpful to see the filament sag test and the impact of the heater location.
The new version of the dryer you mentioned is from FixDry not Eibos, however. I was hoping they fixed these issues but the apparent no response your you reaching out to them makes me question their service and support as a company.

[@DubElementMusic]

Very good high quality and informative, thanks.

[@ThisDesignedThat]

Glad you enjoyed it!

[@mrjayd]

the new model you showed is not an Eibos brand. It is made by Fixdry.

[@childintime7]

Again very nice and informativ Video! Thanks for your work!

[@FalseDeities]

Great review man. Just ordered the aliexpress one. Hope it has that heater fix.

[@ThisDesignedThat]

Hope you enjoy it!

[@davidsh331x]

BE AWARE - These Eibos bags have a very high failure rate. The valves leak like crazy. If not on first use, then on second or third use. The company ignores complaints and requests for replacements. They just go in the trash. The USB electric pump works fine. It's the valves in the bags that fail. Buyer beware...

[@ThisDesignedThat]

thanks for the update, I have had any leakages yet but i dont use them all that much, only to store filament long term

[@nonameextra4342]

Can you provide a link for the big rollers, please?

[@ThisDesignedThat]

www.printables.com/model/366983-eibos-cyclopes-extension-rollers you are probably better off printing a big roller that spans the entire width of the original roller as these are a bit finicky to place the spool onto but I was trying to save filament so that why I designed it this way. Hope it helps.

[@nonameextra4342]

@@ThisDesignedThat thank you! I thought so and will make it longer when I get the time. Never had an issue with filament being close to the heater, but better be safe than sorry.